I changed the rectifier plate in my old Snap-on battery charger model ya16-7 b and now it works I didn't know what the part name was or what to fix until I watch this video thanks very helpful video
Hello Nice video I’m looking at a used 6006 fleet charger. What’s a good price to pay. It looks in good condition. I will test prior to making an offer. Thank you
Would like to ask this expert if there is a rectifier kit with more capacity than the 610110 that I can use on my Associated 6001A?. Thanks What about the 610364?
my forklift charger is 20 yrs old working good, getting a new forklift w new battery, should I change the charger also, to protect my investment, does the charger technology as evolved since to charge a 36V 750ah battery?
I picked up an ESS6008MSK for almost nothing, and it charges on all 3 settings but i think at a lower amperage than intended. shows from 5-15 amps depending on which setting its on. in the crank boost setting the amperage never increases, stays around 20 amps or so. can the rectifier partially fail?
I have a Lincoln charger and while charging a car battery the leads touched each other and arc'd . Now doesn't work but has sound so power is coming in..when I tried to hook up to another car battery the positive cable sparked when I attached it. This happened when the charger had not been plugged in yet. Any help appreciated.
Hello i was wandering if you know how to repair a forklift 48 volt battery charger i accidentally hooked it up to 480 volt, 3ph power but the charger was wired for 240 volt 3ph so when i turned the power on after about 1 min. the charger made a loud explosion sound and it smelled like burned but the breaker didn't go off is it fixable would we need to check rectifier or replace the transformer control starter? any advice would be appreciated..
I HAVE A CHARGER 6/12 VOL BATETERY STARTE SOLAR 360 MODEL 141-225 THE PROBLEM IS THAT IT SMELLS ON THE PARTS LIKE WHICH YOU ARE CHANGING AS YOU CALL ARE THEY THAT CONNECT WITH THE TRANSFORMER THANK YOU.
Thanks For the Video, Very Helpfull My Old Snap-on charger has the same test results but with no available parts. I took the Rectifier apart but I don't see anything "burnt". Could you be very specific on what exactly is burnt. All of the diodes are loose and testing each one individually tests good.
Snap on chargers are made by Associated. I am almost sure you will find the part with them. The people that made this video also sell associated charger parts. check with them.
drj Westfield Wisconsin where can I buy a new rectifier kit for a chacago electric 100/200amp battery charger #46944. Also can you put a larger rectifier in so that it could handle the load or am I just stupid , don't know anything about electronics.someone said it needs a rectifier kit where can I get the kit and for how much.thank you for your help David Jones. C
Hi Pete, Awesome,you helped find the problem.I have a snap-on charger with bad rectifier plate..Snap- on says they don't sell the replacement part.Where can I get the plate from? Thankyou.
Great video... My Snap on charger model YA167B is working but the output voltage (on the clamps) is only 10.5 VDC, is this a rectifier plate issue as well? Thanks
So the main transformer on this is Aluminum, not Copper? Curious also if the rectifiers on the US20 model are similar and how much they cost to replace?
I'm debating which to purchase right now. It doesn't look like the US20 has the same heavy duty rectifier or the vacuum sealed transformer of the higher end models. But right now it's 180 bucks vs the next model up being around 450. Having trouble deciding.
@@ClaytheBMXer Apparently @automaticrepair doesn't answer questions... I lost confidence in the associated chargers after seeing this. Got myself an old used Schumacher dirt cheap, did some minor repairs and it works like a champ.
@@Jerseyhighlander I've actually tried to buy several used chargers now, but either been ghosted or the seller refused to let me see it functioning first. Our shop has a couple of older wheeled Schumachers. I was originally going to buy one of the same models, but then found they didn't have that model and nothing manual. No luck finding used manual mode Schumacher chargers around me for a reasonable price. Ended up with a small DSR "pro" series that is utterly useless. May not reflect on older models, but it's put a sour taste in my mouth. I haven't looked so far, but are parts available for the older Schumachers? Might end having to repair ours at the shop, both are finicky. One charges at 18V on 55A mode, so we only use it on 20A mode (automatic never ever worked). I tried to buy an old Associated 6010 (no suffix), and when I emailed associated they actually found me the old diagram and parts listings and I verified I could get replacements.
Trying to get my battery charger working mine is a Chicago electric the big 200 aunt rose around kind what it's doing is it has continuity even when it's unplugged from the wall
Looks like a great video. I’d love to give it a thumbs up. But after reading the comments I see he does not reply to the videos. Can’t give a thumbs up
friend I have a battery charger that has damaged the rectifier diodes and the transformer booted me a voltage of 24 volts I could make an adactation with another type of rectifier, because it is 250 amp if I adapt several rectifiers would do it in parallel to get at 250 amp thanks.
Im nervous to work on my charger when I saw there was a Transformer inside.. Are there parts inside the charger that we shouldnt touch with our hands to avoid getting shocked to death? My charger stopped working.. I heard a pop and smelled something burning. I opened it up and saw there are four wires running to each terminal on the rectifier plate. noticed three of the four wires were broken off their connectors to the terminal.. im guessing its the positive terminal.
Christopher Jones it’s always the capacitors that you don’t want to touch..you have to short them to discharge them with a screw driver or something ..even when it’s unplugged the capacitors could shock you
What a terrible design, they should have fuses that burn out before the diodes cook, and I don't mean the fuse plates on the diodes, that once the first one burns out it places 25% more load on the rest then when the second one burns out it puts 50% more load on the rest.
I don't want to buy a whole rectifier plate assembly, couldn't anyway as parts for my TOP DOG model 750 are not available. Just replacing all the button diodes is much cheaper. My charger is an older model that does not have the fusible links. Diodes are mounted directly on an aluminum plate in two lines of 6 diodes per line. I took photos of the diodes showing direction of polarity for each line but of course the hard drive on my laptop died and I lost the photos so need help determining the diode polarity for each line. I can send photos of the outside and inside of the charger if I knew where to send them.
Very flimsy construction thease diode plates! Y would have modyfied it whith bigger single bly diodes, the also use in mig welders, there mutch more rugged , and mutch more amps resistand.
where do you find this diodes yo mention here. My battery charger uses the 610100 diode plate replaced in this video. I understand they are about 500 amps plates.Thanks for your answer.
any good electronic store , or just brouse internet, dont know how it is in the states, but here in holland we can order for instance at Conrad, or a special electronic parts site.these are diodes with a mounting thread on it, just dril a hole , and put a nut on it. its mutch more rugged, and they last forever.
MrBugsier5 Thanks a lot for answering. This plate has 10- 25 amps diodes,I will look for diodes of more than 50 amps capacity at 60 volts AC. Hope I can find them.
hi everyone ,if anyone else trying to find out how to recondition batteries try Knewreck Rapid Renew Guide (do a google search ) ? Ive heard some extraordinary things about it and my friend got great results with it.
*interesting points ,if anyone else trying to find out how to recondition used car batteries try Panlarko Recondition Planner ( **lovy.biz/zrsy** ) ? Ive heard some super things about it and my m8 got great results with it.*
Michael it’s not a cheap design go look at a Schmacher battery charger most have only 2 diodes,as you can see associated battery chargers use a lot more !
It's nice to hear an expert at work. No wasted words,, no bad sound , no shakey camera. Just solid advice, thanks
This is the best repair video I have seen yet on how to repair a large shop battery charger.
Straight forward and easy to understand- good job.
Straight to the point , no bull . Just right . Excellent . Thanks . Well explained .
I have 6 of these things. Because of you I fixed them all. Thank you.
just got a new job repairing battery chargers, Great vid, I started at ac side , got yelled at , had one diode flipped , got yelled at
Great video, straight forward!
From Persia
Thanks for the Instructions to test the Charger, I would Love to see what GOOD Diodes look like compared to these bad ones......
Great job, I've never fixed a rectifier plate before, now I can't wait to fix one lolol :) Thanks
U Work like a professional
Thanks for video.
nice work
Thank you Pete for the video...I have voltage but no amperage,is this also a diode problem ? thanks.
what do you mean cranking the unit too long? Like have it on without any load? I want to know cus we have 2 dead chargers. Attempting to fix one
Would it be difficult to get a transformer for a charger like this. Or a larger 24v one, ? Thanks..
I changed the rectifier plate in my old Snap-on battery charger model ya16-7 b and now it works I didn't know what the part name was or what to fix until I watch this video thanks very helpful video
Free Davidson where did u order it from? i have a fast 420 i need to do the same thing with
I just Googled rectifier plate for Snap-on battery charger model ya167b .Century tools and equipment shows part list
Free Davidson ok..thanks..I'll give it a try
Hello Nice video I’m looking at a used 6006 fleet charger. What’s a good price to pay. It looks in good condition. I will test prior to making an offer. Thank you
great job ! keep it simple
professor as it is called that piece that is disarming where the transformer cables go and how many are the rectifiers for a 360 amp charger
Awsome. Just what’s I was looking for. Thank yiu
I have a 6001a which is a 6 and 12 volt charger, could it be easily converted to also charge 24volts by possibly just adding to what's there?
Thank you!!!!
Would like to ask this expert if there is a rectifier kit with more capacity than the
610110 that I can use on my Associated 6001A?. Thanks
What about the 610364?
my forklift charger is 20 yrs old working good, getting a new forklift w new battery, should I change the charger also, to protect my investment, does the charger technology as evolved since to charge a 36V 750ah battery?
Hi saw your video and it help a lot , thank you . I have a question, how much ripple charge is acceptable from a battery charger?
I picked up an ESS6008MSK for almost nothing, and it charges on all 3 settings but i think at a lower amperage than intended. shows from 5-15 amps depending on which setting its on. in the crank boost setting the amperage never increases, stays around 20 amps or so. can the rectifier partially fail?
thank you
I have a Lincoln charger and while charging a car battery the leads touched each other and arc'd . Now doesn't work but has sound so power is coming in..when I tried to hook up to another car battery the positive cable sparked when I attached it. This happened when the charger had not been plugged in yet. Any help appreciated.
Hello i was wandering if you know how to repair a forklift 48 volt battery charger i accidentally hooked it up to 480 volt, 3ph power but the charger was wired for 240 volt 3ph so when i turned the power on after about 1 min. the charger made a loud explosion sound and it smelled like burned but the breaker didn't go off is it fixable would we need to check rectifier or replace the transformer control starter? any advice would be appreciated..
The paper with the new parts does not tell me which direction the printed diodes are supposed to be any help here?
I HAVE A CHARGER 6/12 VOL BATETERY STARTE SOLAR 360 MODEL 141-225 THE PROBLEM IS THAT IT SMELLS ON THE PARTS LIKE WHICH YOU ARE CHANGING AS YOU CALL ARE THEY THAT CONNECT WITH THE TRANSFORMER THANK YOU.
Thanks For the Video, Very Helpfull
My Old Snap-on charger has the same test results but with no available parts.
I took the Rectifier apart but I don't see anything "burnt". Could you be very specific on what exactly is burnt.
All of the diodes are loose and testing each one individually tests good.
Snap on chargers are made by Associated.
I am almost sure you will find the part with them.
The people that made this video also sell associated charger parts. check with them.
Where can I buy a Schumacher rectifier at? Been looking all over.
drj Westfield Wisconsin where can I buy a new rectifier kit for a chacago electric 100/200amp battery charger #46944. Also can you put a larger rectifier in so that it could handle the load or am I just stupid , don't know anything about electronics.someone said it needs a rectifier kit where can I get the kit and for how much.thank you for your help David Jones.
C
PROFE AS THE PART IS CALLED THAT LOOKS LIKE TWO DISCS AND WHAT IS ITS FUNCTION
Okay what about a Schumacher charger I don't see a rectifier a play in that or is that the aluminum plate it's a automatic charger
hello. its 2 diode rectifier? or bridge?
I know this is old but
Can you still get DC voltage but no current (amps) with a bad rectifier
Thanks
tendrias lo datos del nucleo el diagrama de conexion de la maquina
i have a 6010 a which way does the diodes go
this guy is the nuts ..
the reifiers that mycarrier uses are similar to that
how much A/C in the presence of D/C is acceptable? my charger is putting out 36 volts with about 6 volts A/C
Would this be the problem if the charger won't charge but engine start works?
You know of any charger units that are for sale
Hi Pete, Awesome,you helped find the problem.I have a snap-on charger with bad rectifier plate..Snap- on says they don't sell the replacement part.Where can I get the plate from?
Thankyou.
Great video... My Snap on charger model YA167B is working but the output voltage (on the clamps) is only 10.5 VDC, is this a rectifier plate issue as well?
Thanks
Was wondering if u have fixed ur charger and what was wrong with it, I got YA165 and I get only 10.2 volts
PROFESSOR GOOD VIDEO YOU CAN PUT IT IN SPANISH THANK YOU.
So the main transformer on this is Aluminum, not Copper? Curious also if the rectifiers on the US20 model are similar and how much they cost to replace?
I'm debating which to purchase right now. It doesn't look like the US20 has the same heavy duty rectifier or the vacuum sealed transformer of the higher end models. But right now it's 180 bucks vs the next model up being around 450. Having trouble deciding.
I looked up the parts on one of the parts websites and the US20 parts have different descriptions and pictures.
@@ClaytheBMXer Apparently @automaticrepair doesn't answer questions... I lost confidence in the associated chargers after seeing this. Got myself an old used Schumacher dirt cheap, did some minor repairs and it works like a champ.
@@Jerseyhighlander I've actually tried to buy several used chargers now, but either been ghosted or the seller refused to let me see it functioning first. Our shop has a couple of older wheeled Schumachers. I was originally going to buy one of the same models, but then found they didn't have that model and nothing manual. No luck finding used manual mode Schumacher chargers around me for a reasonable price. Ended up with a small DSR "pro" series that is utterly useless. May not reflect on older models, but it's put a sour taste in my mouth. I haven't looked so far, but are parts available for the older Schumachers? Might end having to repair ours at the shop, both are finicky. One charges at 18V on 55A mode, so we only use it on 20A mode (automatic never ever worked). I tried to buy an old Associated 6010 (no suffix), and when I emailed associated they actually found me the old diagram and parts listings and I verified I could get replacements.
@@Jerseyhighlander I'm actually relying on a very old craftsman manual 2/10A charger and 50A jump unit right now. Works great, but need more juice ha
Trying to get my battery charger working mine is a Chicago electric the big 200 aunt rose around kind what it's doing is it has continuity even when it's unplugged from the wall
I have a Jegs charger....can I get parts??
where to you buy rectifier?
Hello, can i use that unit for a multiple charging around 4 batteries?
Sure ,long as connected properly negative to negative ,positive to positive. I had 8 charging no problems , must be ventilated for safety
Looks like a great video. I’d love to give it a thumbs up. But after reading the comments I see he does not reply to the videos. Can’t give a thumbs up
FRIEND AS YOU ARE CALLED THAT PIECE THAT YOU ARE CHANGING TO THE CHARGER
THE NAME OF THE PIECE THAT IS CHANGING PLEASE THANK YOU.
i need to know where to get a Sun BC 160 Rectifier...anybody know??
friend I have a battery charger that has damaged the rectifier diodes and the transformer booted me a voltage of 24 volts I could make an adactation with another type of rectifier, because it is 250 amp if I adapt several rectifiers would do it in parallel to get at 250 amp thanks.
16 v out ..isn't that gonna damage battery?
very good video teacher you could translate to Spanish to understand better thanks.
where to buy the diode only not the whole rectifier
sir any one can help? i have a transformer 12amp.. 13vDC what value of rectified diode i will used? & the value of a capacitor tnx guy pls help?
I've been researching into fixing a car battery and discovered a fantastic website at Magic Mender Wizard (check it out on google)
Does anyone have an idea why the charger produce only 10.2 volt. It's an old snap on ya165 with brand new diods,
AND IT WILL BE THAT YOU CAN TRANSLATE TO SPANISH THANK YOU.
Im nervous to work on my charger when I saw there was a Transformer inside.. Are there parts inside the charger that we shouldnt touch with our hands to avoid getting shocked to death? My charger stopped working.. I heard a pop and smelled something burning. I opened it up and saw there are four wires running to each terminal on the rectifier plate. noticed three of the four wires were broken off their connectors to the terminal.. im guessing its the positive terminal.
I recommend You do not work on the charger while it is plugged in.
Christopher Jones it’s always the capacitors that you don’t want to touch..you have to short them to discharge them with a screw driver or something ..even when it’s unplugged the capacitors could shock you
What to do if both wires are touched pastive and igative
Plz
has anybody had diodes check ok but no voltage just pulled two 6002s assoc. down only 10volts link ok new bridges work ok nneed to figure this one out
FRIEND THAT VOLTAGE VOTES THAT TRANSFORMER AND IF IT IS IN AC. O DC.
TOM PIPPS . FOAM - BATON ROUGE LOUISIANA USA . HI HELLO .
What a terrible design, they should have fuses that burn out before the diodes cook, and I don't mean the fuse plates on the diodes, that once the first one burns out it places 25% more load on the rest then when the second one burns out it puts 50% more load on the rest.
I don't want to buy a whole rectifier plate assembly, couldn't anyway as parts for my TOP DOG model 750 are not available. Just replacing all the button diodes is much cheaper. My charger is an older model that does not have the fusible links. Diodes are mounted directly on an aluminum plate in two lines of 6 diodes per line. I took photos of the diodes showing direction of polarity for each line but of course the hard drive on my laptop died and I lost the photos so need help determining the diode polarity for each line. I can send photos of the outside and inside of the charger if I knew where to send them.
I got my button diodes from Amazon
Hi my name is Richard I have a CD600 BATTERY CHARGER THAT IS NOT CHARGING MY BATTERY PLS HULP
Google the name and model ask for rectifier plate.may come up.wish me luck.Have 2 Schmacher chargers to fix
Very flimsy construction thease diode plates! Y would have modyfied it whith bigger single bly diodes, the also use in mig welders, there mutch more rugged , and mutch more amps resistand.
where do you find this diodes yo mention here.
My battery charger uses the 610100 diode plate replaced in this video.
I understand they are about 500 amps plates.Thanks for your answer.
any good electronic store , or just brouse internet, dont know how it is in the states, but here in holland we can order for instance at Conrad, or a special electronic parts site.these are diodes with a mounting thread on it, just dril a hole , and put a nut on it.
its mutch more rugged, and they last forever.
MrBugsier5 Thanks a lot for answering. This plate has 10- 25 amps diodes,I will
look for diodes of more than 50 amps capacity at 60 volts AC. Hope I can find them.
There is a loud noise coming from my transformer
fuck that, put 2 big 'stud rectifiers diodes' problem solved forever.....$15 dollars shipped free, aliexpress
In my "DIY 6A charger" I used Д-161-320 (320A diode), X4 :D
Associated not happy.
don't try this if your a goober you will hurt yourself ijs.
hi everyone ,if anyone else trying to find out how to recondition batteries try Knewreck Rapid Renew Guide (do a google search ) ? Ive heard some extraordinary things about it and my friend got great results with it.
*interesting points ,if anyone else trying to find out how to recondition used car batteries try Panlarko Recondition Planner ( **lovy.biz/zrsy** ) ? Ive heard some super things about it and my m8 got great results with it.*
I am somewhat exhausted; I wonder how a battery feels when it pours electricity into a non-conductor?
Solar and Storage Battery Reconditioning
Cheap design. Expected results. Failure.
Michael it’s not a cheap design go look at a Schmacher battery charger most have only 2 diodes,as you can see associated battery chargers use a lot more !