Video

Just got one for free. Gone to rebuild it.

i have a 6010 a which way does the diodes go

16 v out ..isn't that gonna damage battery?

great job ! keep it simple

where to buy the diode only not the whole rectifier

Does anyone have an idea why the charger produce only 10.2 volt. It's an old snap on ya165 with brand new diods,

hello. its 2 diode rectifier? or bridge?

What's the little cup at the top center of the cylinder tube-barrel? I'm not familiar with and my Lincoln All American has a plastic cup appears, that the hydraulic fluid can come out of and does if the jack is placed on it's side. Wondering what that part is supposed to be and if not open as-found, what's the replacement part?

I have a Jegs charger....can I get parts??

Do you guys still repair these cylinders?

Where can I buy a Schumacher rectifier at? Been looking all over.

This is the best repair video I have seen yet on how to repair a large shop battery charger. Straight forward and easy to understand- good job.

I have a Lincoln charger and while charging a car battery the leads touched each other and arc'd . Now doesn't work but has sound so power is coming in..when I tried to hook up to another car battery the positive cable sparked when I attached it. This happened when the charger had not been plugged in yet. Any help appreciated.

Hi my name is Richard I have a CD600 BATTERY CHARGER THAT IS NOT CHARGING MY BATTERY PLS HULP

how much A/C in the presence of D/C is acceptable? my charger is putting out 36 volts with about 6 volts A/C

This looks identical to my Lincoln USA2000 jack. Thanks for the video!

I know this is old but Can you still get DC voltage but no current (amps) with a bad rectifier Thanks

drj Westfield Wisconsin where can I buy a new rectifier kit for a chacago electric 100/200amp battery charger #46944. Also can you put a larger rectifier in so that it could handle the load or am I just stupid , don't know anything about electronics.someone said it needs a rectifier kit where can I get the kit and for how much.thank you for your help David Jones. C

I have a 6001a which is a 6 and 12 volt charger, could it be easily converted to also charge 24volts by possibly just adding to what's there?

Google the name and model ask for rectifier plate.may come up.wish me luck.Have 2 Schmacher chargers to fix

Looks like a great video. I’d love to give it a thumbs up. But after reading the comments I see he does not reply to the videos. Can’t give a thumbs up

just got a new job repairing battery chargers, Great vid, I started at ac side , got yelled at , had one diode flipped , got yelled at

Not sure what I just watched.

where to you buy rectifier?

how long is to long on start mode that it burns out?

has anybody had diodes check ok but no voltage just pulled two 6002s assoc. down only 10volts link ok new bridges work ok nneed to figure this one out

You have any low profile shoulder screw

What to do if both wires are touched pastive and igative Plz

Straight to the point , no bull . Just right . Excellent . Thanks . Well explained .

Would this be the problem if the charger won't charge but engine start works?

I picked up an ESS6008MSK for almost nothing, and it charges on all 3 settings but i think at a lower amperage than intended. shows from 5-15 amps depending on which setting its on. in the crank boost setting the amperage never increases, stays around 20 amps or so. can the rectifier partially fail?

Hi saw your video and it help a lot , thank you . I have a question, how much ripple charge is acceptable from a battery charger?

Great video... My Snap on charger model YA167B is working but the output voltage (on the clamps) is only 10.5 VDC, is this a rectifier plate issue as well? Thanks

Hello i was wandering if you know how to repair a forklift 48 volt battery charger i accidentally hooked it up to 480 volt, 3ph power but the charger was wired for 240 volt 3ph so when i turned the power on after about 1 min. the charger made a loud explosion sound and it smelled like burned but the breaker didn't go off is it fixable would we need to check rectifier or replace the transformer control starter? any advice would be appreciated..

You know of any charger units that are for sale

Great video, straight forward! From Persia

I have an issue with my 2 ton tank cylinder ... there is something on the bottom and I am not sure if that is normal or some sort of seal that is just stuck there and needs to be remove and replace on the piston? Any advice on how I can pull it out?

what is inside the cylinder? Can you show the inside of the cylinder on your next you tube presentation? Thanks.

Awsome. Just what’s I was looking for. Thank yiu

I put it in my pool. It gets rid of all the slow weak kids that aren’t strong enough to swim away from the suction. Natural selection at its best

That song is my JAM!!!!

Okay what about a Schumacher charger I don't see a rectifier a play in that or is that the aluminum plate it's a automatic charger

I have 6 of these things. Because of you I fixed them all. Thank you.

Hello Nice video I’m looking at a used 6006 fleet charger. What’s a good price to pay. It looks in good condition. I will test prior to making an offer. Thank you

Great job, I've never fixed a rectifier plate before, now I can't wait to fix one lolol :) Thanks

How much to repair a hydraulic unit?

*It's is truly a low profile jack=>>**share4.photo/pCarJack?R44** It went right under my e90 BMW 335i, and coupled with some jack stands and chocks it made the work very straight forward. I saved enough on labor to easily justify the cost.*

*The jack works as intended as a low profile floor jack=>>**share4.photo/pCarJack?H34 ** The hydraulic pump is comparable to a regular size floor jack and is not a "quick" jack style so, expect to take a little more time than expected on the floor while jacking your vehicle up.*

U Work like a professional

I don't want to buy a whole rectifier plate assembly, couldn't anyway as parts for my TOP DOG model 750 are not available. Just replacing all the button diodes is much cheaper. My charger is an older model that does not have the fusible links. Diodes are mounted directly on an aluminum plate in two lines of 6 diodes per line. I took photos of the diodes showing direction of polarity for each line but of course the hard drive on my laptop died and I lost the photos so need help determining the diode polarity for each line. I can send photos of the outside and inside of the charger if I knew where to send them.