Peugeot 3008 1.6 turbo petrol, P0299 and P2261 no power and limp mode. Fault finding and repair.
Vložit
- čas přidán 23. 04. 2021
- Consider to support my channel and all the hard work put into it at / lmautorepairs
Thank you
Hi
This car Peugeot came to me with the engine light on, very under powered, and if pulled over 3.5-4k RPMs, would go into limp mode..
A few things wrong with it, and ultimately, found both, the problem, and what caused the broken part to fail...
Follow me on this video to find out what was the problem and how to resolve it.
Hope you enjoy the video.
Any questions or comments put them below.
Like always, thank you for watching! - Auta a dopravní prostředky
No fuel most of the time when customer bring the car in. Here in my place is the same thing. Exspecialy when the car needed some more test driving. But if the fuel tank have to be drop, then the fuel tank will be full. 😆
Thank you for the video Luis. 👍
🤣🤣
👍👍👍
Thank you for watching!
What a nightmare! Thankfully you persevered until all issues resolved. Well done for an excellent job!
Thanks!
👍👍👍
Wish every country to have smart people like you that's showing us how the thing's work :) thank you mate and wish you happy day's
😊
Thanks... for watching and for your comment!
There were some things I wanted to write but in the end you did a fine job Luis and didn´t change anything that wasn´t necessary . The non comm with the ECU was a bit strange but than again , it has happened to me also . With a charger connected weird things and with a new battery all OK . Never second guessed it .
Over time I realised that low or weak batteries will provoke all sort of weird things...
Some cars are more affected than others though...
👍👍👍
Excellent video Luis. I like your honest work. U so lucky with customer who understand the problem is normally not just 1 issue. Excellent result well done.
Not always...🥺
In this case yes... was that or not having the car fixed...😋
Thanks, for watching and for your comment!
👍👍👍
As a home Mechanic find your videos helpful and informative thanks
😊
Thanks!
Luis perfect Job. Thanks for your Video, all good for you and your Family.
😊
Thanks!
I have the same problem with my 308 turbo, same engine. See your video give me some ideas to check. Thank you very much. 👍🏻
😊
Thanks!
Hope you find the issue!
🤞
👍👍👍
LUIS, AWESOME video and information fixing this car with logic step by step one thing as i do always with turbo problems/ boost power i use smoke machine to check for any leaks first with all the plastic they are using those days as u know they crack with time and other thing it was good to see fuel trims pids that would show 100% lean mixture because of that leaks as always enjoyable to see the master working thanks for sharing brother. cheeeeers
👍👍👍
Now that's a good repair video :). Loved it. Thanks !
😊
Thanks!
👍👍👍
Hi mate, nice video. Exhaust gas pressure check procedure helps to diagnost a bad cat. But this time camera make a good job. Thanks for video.
Marius.
Very true...
I don't have one of those gauges... might need to get one...😋
Thank you for watching!
Thanks for the video gives me lots of hint .i really appreciate your effort 👌 well done
😊
Thanks!
👍👍👍
good job, under difficult conditions, and no wasted money is a bonus, working nights as well ... respect man
😊
Thanks!
👍👍👍
Great work !! As always appreciate you taking the time to make these videos 👍🏻
😊
Thanks!
@@LMAutoRepairs hi I got a peughto 207 gti on a 58 got a p0087 code low fule pressure rail it's spluttering and popping and banging I've changed the fule pump in the tank and the one on the engine changed the fule sender spark plugs put loads or money spent on car and problem is still the same
Have you tested the pressure sensor?
👍👍👍
@@LMAutoRepairs that's new to mate that was the first thing I've changed
@@LMAutoRepairs were u based to may be I could bring my car up to u and I pay u for fixing it I'm 3g in to car oready mate 🤔
great job ,as always. keep up the great work
😊
Thanks!
Great content as always
Thanks!
👍👍👍
Thank you for another great video!!!
😊👍👍👍
Thanks a lot for the video I have same problem with my car 3008 1.6 thp 2011
😊
👍👍👍
Good work.thank you.wondering why that ecu significant blocked exthaus system instead of turbo preassure?there are 2 sensors on cat in and out to measure that but no any fault code.if you put filters like dpf,cat,egr onto exthaus systems that will reduce engine power in long therm usage 2x2=4
Was the poor mixture due the broken intake... As I briefly explained...
Seen it more than once...
👍👍👍
Hello louis, good job, in diagnostic we should know the basics of mechanic 😊😊,
😊
Thanks!
👍👍👍
@@LMAutoRepairs you are welcome
one thing I have seen a few times now with the THP prince engine that is a easy fix but hard to find and the symptoms are very similar to this the air pipe to the throttle body pushes itself off and because it is held in place by the bolts on the plastic part of the pipe every thing seems to be ok until the turbo kicks in and pushes the pipe away from the throttle body
👍👍👍
Low fuel🤣🤣🤣. Good vid and fix👍
😋
Thanks!
👍👍👍
The catalytic converter can be cleaned. Usually the companies that sell replacement catalytic converters want the original part back to re-manufacture it most likely.
Not in this case...
Thank you for watching!
Good job
Thank you!
You're right. When the cover fails it blocks the exhaust. These engines are turds. Always seems to be same scenario though, knackered battery, no fuel, no love care and attention. Tight owners.
😊
👍👍👍
Very tight...
Seems to be a PSA thing, the diesels have the same issue when their PCV or EGR system fails it starts crudding up the diesel particulate filter.
Awesome video, thank you so much, I have Peugeot 208 GTI with same engine, I have a similar issue but if I switch the car off and return to it after some time it runs perfect for about 5 mins and then I feel a loss of power. Have the same code p0299. It has only 28k so cat shouldn’t blocked. Any ideas would be appreciated it.
The cat can block easily if the car has been running with issues...
Check for intake leaks etc...
Thank you for watching!
One of tree things is check cat. Put hand on exhaust, if is cold, cat is 90 % block. I made tool for this. Manometer, pipe and fit. O2 sensor out and put tool. On high rpm, about 3000, presure must be under 0,3 bar.
👍
I don't have a sensor...
Thank you for watching and for your comment!
I am not a mechanic but removing and putting the hose back in place is normal. Charging the breakage is ok for me.
But very kind of you.
That's
😊
👍👍👍
Peugeot/Citröen needs extra love. Anyways, down pipe is life. Remove that catalytic crap.
😊
Thank you for watching!
👍👍👍
I think that battery would cause the system to go haywire what was that broken off thing for
Why such ecm don't have lean condition monitor? Cheaper production to design without a MAF? Or something else I'm missing!?
It is French... lol
Who knows...
👍👍👍👍
Been looking at the wife's 3008 thp as it seemed to be down on power. Just a heads up, the diverter valve is a weak point and the bmw mini one fits, is cheaper and stronger too! Handy! The rear pcv can be blocked with a Peugeot part as they realised that the breather causes massive carbon build up. I'll be checking the cat tomorrow though as she only does 5 miles a day commute..... Awesome video and thanks!
😊
Thanks...
Hope you get it sorted!
🤞
Super knock triggered on the fault codes... Hope this isn't another cam chain.. 😳
🤞
any ideas about p2192 code?
Just a thought how come the rear lambda sensor didn't report any fault code for Cat like (P0420) code any idea...?
🤷♂️
It is a peugeot...
Everything is possible...
🤣🤣🤣🤣
Thank you for watching!
👍👍👍
I have a citroen c4 loeb eith same error foult. No power too rich mixture.Well the next step is to take the catalyst out and replace it.
Thank you for the very informative video. I have a 207 turbo with the p0299 error code after revving more than 3500 rpm for 3 seconds. I have checked vacuum, changed the electric valve. How can I check if I need to replace the valve cover? Is it possible to verify if the valve cover have failed?
Watch from minute 29:00...
You can also smoke test (which I never done on this video), if any leaks the smoke test should highlight them...
Then the valve on the cove as I've also explained...
👍👍👍
@@LMAutoRepairs the valve on the back of the cover should be open if the pressure is low and close if the pressure is high, I assume. That makes the smoke test more complicated.(at least for me, I am a noob).
@LMAutoRepairs Thanks, I have the same 2 codes as you have at 29:00. I suspect the air pressure just escapes through the valve cover back into the low pressure side If the back valve stays open.
Can't figure out how to test if the valve closes under pressure?
👏 Well done, there good cars if looked after
👍👍👍
Thanks!
My Peugeot rcz is having the same problem now. My first guess is to change the air intake since it's somehow damaged. I think I might have to check the CAT too. How much did the client spend in total?
I can't remember now... sorry...
👍👍👍
Hey Buddy, did you solve the issue with your RCZ? I have the 1.6 THP 200 and got P2263 (Turbocharging air circuit, pressure too high - intermittent) following with P0299 (Turbocharging air circuit, pressure too low - permanent)
Hello sir .. i have a fiat bravo 2010 with 1.4 turbo engine .. the engine would not start before couple of days .. i tried to make it run by adding fuel remove the negative cable .. now the engine is running but the rpm wouldn't exceed 1000 revs at idle .. even the car doesn't want to move .. no dtc .. tried to change the throttle body but still i have the same problem even the turbo valve doesn't open ... And no revs .. any ideas .. does it have a bad ecu ?
Thanks in advanced for any help 🙂
It is possible... but check live data... your answer is more likely to be there...
Thank you for watching!
Dud battery, no fuel, no road tax. Yep, that sounds about right! Nevertheless, good outcome :D
😊
Thanks!
👍👍👍
Sounds perfect haha.
🤣🤣
Oven cleaner , works all the time!
Hi
I have tried some "home" recipes, and even "professional" products in the past, with some mixed results...
In this case I just didn't want it to come back later with the CAT blocked again...
Thank you for watching and for your comment!
👍👍👍
Can you please inform me , what kind of engine oil do you use for THP ENGINE ? Thanks
Here in the UK, I would use 5W30 fully synthetic...
Thank you for watching!
@@LMAutoRepairs thanks , cause we are suffering from engine oil matter
Would an overboost situation that drops the turbo until you restart the car be caused by a blocked catalytic converter?
VCDS error P0234 on a 2010 VW Touran 1.9TDI BXE 105BHP engine with close to 170,000 on the clock.
Turbo is on the back of the engine at the bottom and it is labour intensive just to inspect, so just trying to compile a list of possible issues.
I have just had the camshaft and lifters replaced and there was a severely worn cam and a few lifters were severely worn.
Usually indicates that the wastegate is stuck closed which builds too much air pressure inside and it can cause big engine damage.
@@blackops2376 but it only seems to happen temporarily and randomly. I was beginning to think there could be a wiring loom issue it was so unpredictable since it happens in all seasons (weather/outdoor temperature), happens rarely, happens with hills but also on the flat.
It’s so bad when I’m stuck behind a car doing 30 in a 50 I daren’t take on any over taking manoeuvres unless it’s clear for a long stretch in case the turbo drops.
Thanks for the feedback, where exactly is the wastegate and does it have any other names?
I thought on my car it was part of it close to the EGR valve?
@@blackops2376 also would this have anything to do with poor starting in colder weather? I know about the usual diesel glow plugs and 3 out of the 4 are working from what I was told, the fourth wasn’t removable without dismantle the head according to the garage.
It’s almost like the car starts to turn over and some blockage or lack of fuel sensing occurs, but, if I remember on a cold morning, I can over come this by pressing the accelerator while it turns the engine on and it forces a smoky throaty start every time.
@@Infiniti25 the wastegate is at the exhaust part of the turbo usually left sife of it its big, attached to it is the actuator but your diesel problems might be because of the EGR get someone to disable EGR it only causes issues
@@blackops2376 I have VCDS, but I would need a remap surely
Quick question @lm auto repairs. Does the ecu from a pug 207 need to in the car to be reprogrammed or can I just send you it to download file for my car and reprogram? Asking here as got no reply from your forum. Thanks in advance
What exactly are you trying to do?
@@LMAutoRepairsthe fan won't come on at 105c as it should and after checking all the loom for a short to + .diagbox says cooling fault integral to ecu I can only assume a driver has failed inside ecu at this point .but oddly the fan comes on after I switch engine off. So this why was asking about programming another 207 ecu thanks
Strange...
If you activate the fan with the diagnostic tool, does it comes on?
@@LMAutoRepairs yes slow and high speed and obvs workes when the air con is on. Inless iv missed something on the loom .it must be a driver in the ecu . This is why I was asking a spare ecu can be programmed out of the car .or dies it need to see the bsi and key ring fir security reasons??thanks for replying.
You can possibly program it out of the car, by clone the ecu, using k-tag or similar...
But, if you can actuate the fans with the diagnostic tool, and they work, then I doubt is going to be the ecu... the control side is the same, whether you actuate them with the diagnostic tool, of they come on when the temp gets to the set point...
Your problem will most likely be something else... I am not completely rule out the ecu, but if is the ecu, is a different circuit...
Can you see the coolant temperature on the live data?
You are boss $$$$$$$$
Hi mate i need some help i have a laguna II ph2 2006 2.0 dci 173bhp.
A mechanic deleted by mistake my injectors, I document my self on the internet and I managed to rewrite the injector codes then I had to reprogram my glow plugs and the car works flawlessly apart the black smoke that comes out from the exhaust(before it dident use to smoke at all!!) I had a look at the injectors correction data ppl say they work properly, I had a look at the egr and it's not clogged, I checked all the intercooler/air/vacuum pipes they are all ok.
once the car lost power just like in one of your renault traffic videos when you press acceleration and notthing would happen but then i put it into reverse and works since then. Cand you suggest me somewhere to start looking? today I'm going to replace my MAS AIR FLOW sensor but I'd need more advice as I'm just a car enthusiast thank you in advance!!
Hi
In which order did you programmed the injectors?
It is common for programming them in the wrong order... double check that if you are not 100% sure you did it correctly...
👍👍👍
@@LMAutoRepairs I took first injector from timing chain side
I am pretty sure on renault injector 1 is the gearbox side...🤔
@@LMAutoRepairs Should I try the other way around then? my engine code is m9r760
Nothing to lose...
😋
Hi.. can egr cause low boost ...?
In some cases. If the EGR is stuck open and it's mounted on the high pressure side, any boost will just blow out the exhaust. Also, if the EGR doesn't work properly, the filters downstream (cat or DPF) can get clogged and this would cause the turbo not to spool.
apple looks nice and clean but the worm was inside :D
😅
👍👍👍
Is the oil change really exceeded by 5,600
🤷♂️
Looked like...
@@LMAutoRepairs That's crazy when you said no road tax and 0 range I knew you where in for a treat they probably gave up on it.
😊
I have way worse ones on the way...
Stay tuned...😉
@@LMAutoRepairs LOL, how low can you go? Love it.
Did you ever have to break a door window to get into the car because the battery died
Never happened...
🤞
😋
@@LMAutoRepairs That's good Louis
Hi, you make nice videos. Please make shorter videos & explain the problem and possible solutions in the video description. Thank you very much.
The videos length is dependent on the problem...
Simple problems are usually shorter videos, bigger or more complicated problems, longer videos...
👍👍👍
Cat at 70.000 needs checking
Prince engine is real royalty in maintinence cost! Bad engine design. Stay away from it in any case!
😊
Worst modern 4cyl engine its possible to buy, Junk from day one.
Peugeots. This one from video is not that bad.
I can remember first 1.6 hdi 16v diesel engines. They was so bad designed and everything fails on these engines. Turbo, oil dillution, dpf, egr, injectors... you name it
All Prince series engine's are garbage not helped by the owners neglecting even the most basic maintenance but the amount I see with timing chain failure running faults carboned up or with HPFP failure is ridiculous.
Bom vídeo...e esse problema de conexão da VCI com a ECU do motor (no grupo da PSA) também acontece por vezes na máquina de diagnóstico da TEXA...e já reparei que primeiro entro na BSI e assim já comunica com a ECU ...não sei se é do próprio sistema do carro ou da máquina de diagnóstico!
Interessante...
👍👍👍
Another one with no fuel and dead battery
😊
Where to take time to work in night shift, repair cars and make videos for CZcams? Do you have 25 hours in your day? 😁
Is it a secret what is your another job?
I sometimes actually wish that days would have 25 hours... 😋
👍👍👍
I just can't understand why does high level specialist not work in proper conditions? Why do you have to work outside in the rain, frost and etc.? In my country you can easily rent or buy a garage and work in it.
You deserve better working conditions!
😊
It is a part time... for now...
👍👍👍