How to split a tractor. Ford 4610 clutch removal
Vložit
- čas přidán 22. 08. 2024
- We split our Ford 4610 to figure out what's going on with our clutch.
SEASON 2 episode 2
Automatic Garage does not own nor claim the rights to any songs in this or other videos.
Composer Name: WAVETOYS Song:INNER FIRE IPI number: 00861760815
Music from CZcams Audio Library [Aka YAL]
Music provided by RFM: • Video
Musictoday80:
/
/ musictoday80
/
www.youtube.co...
Music from Soundcloud
Music provided by RFM: • Video
Music from CZcams Audio Library [Aka YAL]
Music provided by RFM: • Video
Appreciate the video. My Ford 2120 has a similar problem.
I knew what the jumper was for as soon as I saw it. My neutral safety switch is toast so I just connected the two wires without the jumper.
Hey there , I’m from UK , I have a 1984 Ford 7610 , and it done the same thing! All I did to fix it was , there is a rod/bar connected to the clutch pedal and it has a threaded section , basically I spinned the female threaded bit down the thread going away from pedal, connected it up again and problem was solved! Only needed to do it once and no problem since! Apparently the rod/bar sort of stretches through time and has the adjuster to tighten it! It pulls on a lever which you can see at side of engine, when it stretches it can’t pull said lever far enough to disengage the clutch There’s nothing wrong with the clutch! 😊 sorry I’m late in seeing this! It’s literally a 5min job
My problem was the cooked and sticky tractor fluid from the trans seal leaking. It was like molasses on the clutch and flywheel.
good mornig and nice tractor in my pakistan 1978 ford 4610
Been around tractors my whole life. Pilot bearing at end of motor crankshaft is the problem. Pressure plate might be stuck but i doubt it. Good luck
Pilot bearing was perfect.....the hydraulic/tractor fluid was so sticky on the friction disk it wouldn’t release....had a leak...watch the second video...thanks for commenting
Helps to take the fuel filters off before removing the starter
Not really, using the extension and swivel gets you way past the filters anyway. But thanks for leaving a smarta$$ comment.
No problem… must be because I replaced my starter with a front end loader bracket in place so access was tighter. BTW, interesting fact, 4610s were built in England.
Mine has a cab and it always intrigues me to see how much simpler working on dry climate tractors that just have a canopy is! Although I guess the cab doesn’t have to be removed to split the tractor- something I’ve not had to do yet. It’s also nice to see your tractors don’t rust - much - compared to ours in damper climates. Like here in the UK.
I’ve had my 4610 4WD for about ten years and I think it’s a great tractor - no electronics to go wrong!
Thanks for the informative video.
Clutch stuck on my 7600 tied clutch pedal down for a day or two went back and it had released worked fine ever since but I always tie clutch pedal down if I'm not going to use tractor for a few weeks.
This would release if you hammered the brake but soon as you let off would get stuck again. The cooked on tractor fluid was all over the clutch from the leaking input shaft seal causing it to stick. It was leaking oil in the bell housing causing the sticking. Tying the peddle down wouldn’t have fixed or changed my problem. Thanks for watching.
I’m sure you wish people would watch video before commenting. How many times did you tell people what the real problem was.
Ford is gold ✨💛👌
Amazing job !!!
No explanation of why it wouldn’t release. “Sticky stuff on flywheel or Pressure plate makes no sense. So what was the problem? Adjustment?
The problem was the cooked on tractor fluid as I mentioned in the video. It was like molasses on the flywheel. The seal that I showed replacing on the input shaft of the transmission was the one leaking. Of course the clutch material was ruined from being impregnated with all the sticky oil so it had to be replaced. Thanks for watching.
Thank you for this vedio sir!
I am splitting my Deutz Fahr 85. I got stuck with the Huydralic hoses. Especially those Hose to Metal pipes connections. Can't separate them although the bolts are off.
Common ford 4610 issues. Most would have removed inspection plate and soaked it with wd40. Then never store tractor with clutch released.
Not a common 4610 issue or any tractor for that matter, it is common for the clutch to stick if the tractor sits but this tractor didn’t sit. The input shaft seal was the culprit, in the video I showed how sticky the flywheel was from the fluid getting cooked on the flywheel.
What was the cost of rebuilding the clutch vs buying new?
I can’t remember now except for that it was slightly cheaper but better quality than most the garbage made now
What about the pto clutch is it next to the rearend?
4610 has independent PTO, meaning when it’s engaged it’s engaged. There is no PTO clutch.
Hi there any update what was the problem in clutch thx
Video coming stay tuned....been busy with trucks coming in and out to work on...good problem. I have 3-4 videos worth of material I gotta get edited and up. Thanks for following up. Should be up in the next week or so. Stay tuned.
@@AutomedicGarage thanks for reply been watching lot of your videos , good material ,just little more detail on repairs & fitting & setting up data , your videos are clear & nice good base for learning Regards 🙏👍
It’s probably something else broke in there
Do not try this at home
I would recommend anyone with basic mechanical knowledge to try it, wasn’t a bad job.
Took way to much off you made it way harder
Such as? Nothing was removed to do the clutch that didn’t have to be.