Full Tilt's Mustang II IFS Install Part 2
Vložit
- čas přidán 26. 09. 2013
- Part Two of Two - How to install Full TIlt Street Rod's Hub-to-Hub Mustang II IFS Suspension Kit, including crossmember, upper and lower control arms, rack and pinion steering, spindles, rotors and brake kit. More info at fulltiltstreetrods.com
- Auta a dopravní prostředky
Looking forward to installing your kit
Awesome videos. I've been looking to do this for my 66 mustang and was curious about the work of installing this.
Very informative!
MAGNIFICENT YOUR WORK !
VERY NICE !
Man that's badass. When I get that far in my truck I'll definitely give you a call I like that thanks
VERY NICE!
Congradulations!
You sir did it the white way, all these videos and nobody hangs a fender and puts a wheel on before welding it .. nice job sir👍👍
Thanks for the awesome video! Your product seems amazing! I'm just wondering if you would have a front end kit for a 1967 Ford F250. I find lots of front end kits for older Fords and for the F100 - but not the F250
Nice setup
I have a 1931 Lasalle, i would love to change out the front end with this kit.
Yes Sir, can this kit be installed with the motor in place. ? Thanks. Great video.
How do you get the alignment close?
Hi ,great kit ,wish i had one ,do you carry basic crossmember kits for getting started ,i.e for folks on a budget ? I have a '52 Ford f1 project that I'm building, and i came across some upper control arms for a race car in my garage ,that's why I'm wondering if i should go this route ,as opposed to a straight axle i beam front front end ,also how much if you do carry starter kits ,thank you !
What is the O D & I D measurements on yourFrame Rails? is the crossmember made where there is Adjustment ?
how do u find the centerline for it
You have a kit for a '36 Chevy low cab pickup?
If you marked off axle centerline from the factory manuals, would you wheels sit right without fitting fenders? Someone might not have fenders just yet😅 but wants to have a rolling chassis. Also, do you guys offer a top mount that uses shims instead of t-bolt design?
Got anything that works with an actual mustang 2? I have a 78 mustang 2 and I want tubular control arms but all the aftermarket stuff doesn't seem to work with an actual mustang 2.
Looking for a kit for a 1963 nova wagon
How do you determine if you'll have the correct caster angle in the vehicle?
On any of these systems, there is more than enough adjustment room.. just need to make sure you have the ball joints aligned fore/aft and that the spindle is perpendicular to the ground.. should be close enough to 0 camber/caster that you can set where you want.. drag racers will stagger left and right side a bit too :)
I like the information my question is I have a 51 Ford truck , would it be safe to use a bolt on mustang 2 kit or the weld in thanks.
I'm a fan of weld on over bolt on thanks
@@FullTiltStreetRods Thanks I am trying to decide whether to use a chassis already design for my 51 because I don't do any welding an my body is in great shape any suggestions would be appreciated.
Is it ok to move everything forward a bit on a 56 f100 so the wheel is centred? Factory has the wheel set back off centre in the wheel opening.
Yep. That what you want to do to center the wheel
@@FullTiltStreetRods thanks for the quick reply, I’m looking to get rid of the original. straight axle .. what’s your opinion about power steering? Is it worth it? The truck has a 312 Y block and I’m not sure if I could find a power steering pump setup for it..
Hey man, how much is a kit for a 59 apache with air bags?
Gono Lara 2150.00 plus shipping let me know
Hi, can you give me a price for this, for a 58 apache panel please?
I have a 58 apache suburban i love it was going to put this in it but im putting it on my 06 tahoe 4wd chassis! Good luck with your project