Hope 30mm Bottom Bracket
Vložit
- čas přidán 25. 06. 2016
- A look at a Hope Tech 30mm (Threaded)Bottom Bracket
Get your Hope 30mm Bottom Bracket here: tidd.ly/5c32f17f
www.hopetech.com/product/botto...
Tool - HTT188
SUBSCRIBE - bit.ly/2zS1N13
Instagram: / jedmtb
Twitter: / jed_mtb
Facebook: / jed.mtb9
#hopetech #hopebb #hope30mm - Sport
I ride a set of 24mm ones of Hope for 10!!! Years without replacing it... Says a lot about quality. Also 3 years a set of hope wheels without issues
Absolute brilliant Vid mate thanks. Although just installed mine and its quite stiff without using the preload adjuster??
Hello ) Where you buy this key ?
hi, how has the durability been with this bracket, I'm getting tired of buying the shimano ones lol
Hi Michael, I find the durability great on the 30mm ones, Wheels Manufacturing also make a good bottom bracket.
Hi
Are you sure about the seal ring installation? I wonder if the flat face should rather go in front of the bearings
It works both ways, I did find if I use the flat face over the bearing it would rub off the green from the seal.
Why no bearing/spindle sleeve? My BB shell is always coated with dirt whenever I check my BB, and without the sleeve the bearings would be toast in a couple months at best.
The 30mm bearings sit outside the bb shell that's why you don't need a sleeve
How will I know if I need to use the spacer rings ?
Yan Mills Hi, generally you will need to use one on the drive side, I always start with one then check and add more if needed.
Is it save installing bottom bracket in frame without tube bb? I mean from dirt, water, mud, etc
It depends if your bike frame has an open BB design, my frames all have sealed BB's so have no need for a tube.
Are These Reliable and Durable Bottom Bracket?
Bomb Proof?
is there a Park Tool counterpart or alternative for the HTT188 tool?
I'm not aware of any from Park but the OSBB "HP" from Abbey Bike Tools works www.abbeybiketools.com/collections/tools/products/bottom-bracket-socket-osbb-hp
How many spacers did you use? I have a boost.
I use one spacer on the drive side with my boost frame.
Where to buy the specific tool (HTT188)?
UK: tidd.ly/dc7799b6 US: www.fanatikbike.com/products/hope-bb30-bottom-bracket-wrench-htt188
Do we have to buy this . When we buy Crankset ?
Yes unless you already have a 30mm bottom bracket on your bike.
sir you didnt put or install the bb sleeve protector in the frame?
Anthony Sy I don't use a sleeve protector, thanks for watching I appreciate it.
It says stainless I'm assuming that is the ball bearings and the body is made of aluminum?
Yes that's correct.
Races and balls are steel in a SS MR2437 bearing used on hope.
There is no need for a sleeve because the 30mm bearings sit outside the bb shell and the spindle should spin WITH the bearings not On them so there should be no wear on the spindle aside from where the bearings are seated
Is your bike boost ?
Yes, it will work fine on non boost bikes as well.
@@jedmtb I got GX SRAM boost crank 30mm spindle. Spindle goes through BB no problem but It gets jame tight and crank wont spin as I tight up that 8mm nut. Then there is no clearance for crank it hits frame. I posted that hope bb back and went with dub instead
@@Phen0mable SRAM don't make 30mm cranks they only make DUB ones which are 29mm just to make things confusing for everyone, glad you got it sorted :)
@@jedmtb they do. Look up sram gx bb30 its 30mm spindle
then they do dub 28.99 and standard size
@@Phen0mable I should have said they don't make 30mm cranks which work with external threaded BB like the hope as the axle is too short because the BB30 uses press fit.
2:14 - I thought same thing: "Hey, I can use the old TL-FC32 to install my BSA30." Wheels MFG. didn't send me a wrench, but I goddamn well bought American, just can't install American until I buy another $20 dollar wrench that I will most likely never use again. Good on Hope for including the wrench if that was the case.
the 30mm spindle basically takes up all the space inside the BB shell. There is no room for a sleeve.
the RaceFace bb30 has a sleeve... but it doesn't help, the bottom bracket is widely known to be a piece of crap. I wonder if this Hope version is any better?
@@forestyforest it is. Hope BB is very good. You can remove bearings and buy them separately
Without an sleeve, the aluminum 30mm spindle wears out quickly. Not good.
That's a standard bottom bracket tool fella
TheOracleCyclingChannel Hi are you referring to the hope tool?
jed Mtb yup. Standard size as far as I'm aware
TheOracleCyclingChannel It does look like a standard one but the diameter is larger
Luka Gorjup Very true :)
its a tool specific to this bb. Hope part number Htt188. Standard tool does not work
Overpriced shiet :D