Linear Hall effect on E-Bike Throttle - Understanding & Testing

Description: In this comprehensive tutorial, we'll show you everything you need to know about e-bike throttles. From how they work to how to test and disassemble them, you'll learn all the essential information you need to diagnose and repair problems with your e-bike's throttle. Our expert instructor will guide you through the process, breaking down each step into easy-to-follow instructions. By the end of this video, you'll have the knowledge and confidence to troubleshoot and fix throttle issues on your own e-bike, saving you time and money in the long run. Whether you're a seasoned e-bike rider or just starting out, this tutorial is a must-watch for anyone looking to take their e-bike maintenance skills to the next level.
----HALL sensor SIMPLE comparison (Bipolar x Unipolar)--------------------------
• HALL Effect Sensor Com...
----LINEAR HALL Effect sensor (Analog sensor)---------
• Linear HALL effect SEN...
----HALL sensor TRIPLE comparison--------------------------
• HALL EFFECT SENSOR Com...
---HALL effect experiment theory--------------------------------
• HALL EFFECT THEORY Exp...
----HALL unipolar model A3144-------------------------------------
• HALL EFFECT SENSOR - B...
---Linear Hall effect on E-Bike Throttle---------------------------
• Linear Hall effect on ...
#ebikeThrottle #hall #halleffect #hallsensor #ebike

[@BCNomader]

Thank you! Just the information I was looking for. You made my day.

[@engthink]

Nice!

[@jbhawkster]

Very well done. Thank you for this.

[@engthink]

Thanks!!!

[@normanwray1341]

Hello dear friend thank to give me your good advice off that throttle, very interesting 😅😊

[@engthink]

Thanks bro!

[@anpatron4439]

Very nice video! Very useful info about the mixing up of the wires in the connector. Do you have a vid about the way each wire is held inside the connector and how it can be released so the wires can be rearranged inside the connector?

[@engthink]

Thanks, good sugestion I will try to make soon.

[@Lobo-mv2ml]

I have a Phantomgogo R1 36v scooter. The make and model are Sine wave brushless controller 2HM-0. When I tested the 5v red wire coming out of the controller I found that the 5 volt Red Wire is pushing 17.44 volts. I am afraid of connectiing the.controller to the throttle because I do not want to damage the throttle. Is this high voltage normal or is it a defect? Will it destroy my throttle?

[@misoo83]

Hi, i have thumb throttle that have start idle voltage 1.33v and when full run 3.42v, is this ok voltage, is this throttle ok and will this throttle work fine with such voltage values?.
Thanks 🙂

[@vijayakrishnannair]

Nice 👍

[@engthink]

Thanks.

[@LuanaSantos-ol7vy]

Valeu!

[@engthink]

Bons estudos!

[@marvindeximo3709]

Thank you!

[@engthink]

Welcome!

[@NormanWray-hi8cu]

How could you use a baizifu conversion kit brushless kit moto sensor that as wire's red black and yellow 😊😅

[@engthink]

Red = positive, Black = negative, Yellow = throttle proporcianal signal

[@pasqualemacheda]

nel mio acceleratore ci sono 3 fili ,BIANCO ROSSO E NERO .LA MIA BICI E UNA 250 (MARCA VIVA) SENZA LA PREDISPOSIZIONE X L'acceleratore COME LO DEVO COLLEGARE ALLA CENTRALINA .CIAO E GRAZIE SONO CONDOR 69

[@engthink]

Dai colori dei fili dell'acceleratore dovrebbe essere il seguente:
rosso positivo.
nero negativo
segno bianco
Cerca il manuale del controller per sapere dove collegare ciascun cavo. Buona fortuna.

[@plig88luthierandelectronic63]

If I give on the signal , more than 5 volts dc , the motor goes Above the max speed ? .. I have an urbanglide escooter and I search how to unlock the max speed ,, my scooter have 25 km/h top speed , but I don’t know where I unlocked ,, it’s from dashboard or from controller ?

[@engthink]

Its depends how they block the max speed. I am not sure tha the limitation is in the 5Vdc signal from the accelerator.

[@plig88luthierandelectronic63]

Ok for this ,, I have one problem now ,,, I put on rear wheel a onother motor from other escooter , so the front wheel work from the controller 1 and dashboard 1 , and the rear wheel work from second controller and the second dashboard , I take only the signal throttle from first dashboard and I put it on the second dashboard throttle ,, it works perfect , but yesterday, when I give throttle the rear wheel spins backwards as fast it can !!! For some reason , I don’t know , I’ll check all connections and the cables and the phases , all!! I’m thinking to turn the wheel upside down , but the speedometer do not work , because the motor going to the wrong way ,, do you know what happen ? 😢

[@sohagsowdagor2809]

This sensor number please

[@richardbaynham8689]

Cannot see anything screen too low

[@engthink]

Strange, maybe issue in your screen.