Thankyou so much for this, attempting to use this type of pedal to control a solenoid graver me and my wonderful subs are working on, this is a great help even better if I was clever like you blokes :) . What one has the smothest control. Got a few cheap one form ebay to experiment ,Cheers Shaun
Is it the same as magnetic throttle? I have a twist and thumb throttle from 2 different scooters. The thumb throttle only has 2 magnets and a sensor not sure if I want to open the other yet. But yeah, are all electric 3 wire throttles compatible with all 3 wire controllers and is it the same for 3 wire breaks? Sorry for the long message and thanks again.
Hi, i have thumb throttle that have start idle voltage 1.33v and when full run 3.42v, is this ok voltage, is this throttle ok and will this throttle work fine with such voltage values?. Thanks 🙂
So I have a question. If a throttle advertises that it's Voltage is 12-99v, does that mean it's compatible for anything between 12 and 99? So if my bike is 36v, it's not going to blow it?
I have a controller. It has 4 wires to 1 jst-sm. 2 pins for the brakes. And 2 for the throttle, which is a julet 3 pin which the connected julet 3pin cable is only 3 inches long. If I get a longer julet 3pin with open wires on the end. So I am wondering how I connect them ? I bought them from Fiido. They are a matching couple for the L3 bike. Would I wire the green and red together ? Or would I wire either the green or the red one or the other with one of the brake wires ?
I have a controller. And on the controller is a jst-sm 4 pin connector for both the brakes and the throttle together. 2 are for the brakes and that leaves 2 more pins which are of course for the throttle. But, the throttle has 3 pins. I dont have a multimeter and I have never used one. So,, if I switch the pins around to figure out which pin goes where. Could that harm my bike in any way ?
I had no idea that throttles have levels depending on how hard your thumb presses it... I’ve been pressing the throttle so hard no wonder the battery dies
Hi. Your advice please. Samebike L026 350w motor. After about 10mins ride lose (thumb) throttle power. Sometimes occasionally returns. When starting from rest again similar situation. Thankyou.
Hi , my aventure throttle only grabs at eight miles an hour, half the lower speeds are missing, should this be like this? Its made by aventon Thank you in advance
what i want to know is, can you just connect the signal wire to the positive wire? just to get home, like today my ebike has stopped, if i knew ii could just connect the sig to + i might have been able to get home, with no throttle control ofcourse.
@@truth.speaker oh my friend, i know what is the situation now, you need a button battery which is 5volts, you then connect 2 of the 3 wires to each side of this battery, thn you hav throttle. since then ive moved on to a gas powered china doll engine for long range!!!
Help my scooter controller has green, black, red, gray, orange. The new throttle LCD and has red, black, green, blue and yellow. Red to red, black to black green to green...... gray and orange? And blue and Yellow?
Hi, please, I replaced pedal assistant sensor with a throttle on my ebike and it not working. How do I fix the issue. The controller doesn't have separate wire for throttle connection. Greetings from Nigeria
@@ballaratebikes287 I have a great question for you, I am interested in a twist throttle that starts you off slow, because I notice that all the cheap $15 twist throttles that I a have used, knock you off the saddle as soon as you barley turn it to its minimal activation point, I am looking for a throttle that starts off very slow and gradually starts accelerating to full speed. Please refer me to one either through amazon link or a model and model number, I will subscribe to your channel upon you response. thanks
☠️ I've been experiencing extremely dangerous episodes of the motor not stopping as soon as I turn the throttle , related to high humidity conditions ! I think it's because the humidity increases conductivity of the hall sensors in the throttle . can you recommend a good throttle ? I think the manufacturers are going to have to make them water proof. I experienced the same issue with a different throttle , battery and controller. just using the bike after a rain storm is enough to cause the issue. We must have a throttle will a switch to cut power ! ☠️ Also stop using hot glue on the Hall sensors ! It melts were I live ! And make the throttle not Fall apart so easy , and they need to be made with softer grips or made to accept normal grip's.
Thank you!
This is the kind of knowledge I like to hear :D Real knowledge!!
Made me smile when I saw the banana USB.
Is there a way to get these throttles to work with a potentiometer type motor controller. I think the call them pwm?
Thankyou so much for this, attempting to use this type of pedal to control a solenoid graver me and my wonderful subs are working on, this is a great help even better if I was clever like you blokes :) . What one has the smothest control. Got a few cheap one form ebay to experiment ,Cheers Shaun
Is it the same as magnetic throttle?
I have a twist and thumb throttle from 2 different scooters. The thumb throttle only has 2 magnets and a sensor not sure if I want to open the other yet.
But yeah, are all electric 3 wire throttles compatible with all 3 wire controllers and is it the same for 3 wire breaks?
Sorry for the long message and thanks again.
thanks a lot
Hi, i have thumb throttle that have start idle voltage 1.33v and when full run 3.42v, is this ok voltage, is this throttle ok and will this throttle work fine with such voltage values?.
Thanks 🙂
So I have a question. If a throttle advertises that it's Voltage is 12-99v, does that mean it's compatible for anything between 12 and 99? So if my bike is 36v, it's not going to blow it?
I have a controller. It has 4 wires to 1 jst-sm. 2 pins for the brakes. And 2 for the throttle, which is a julet 3 pin which the connected julet 3pin cable is only 3 inches long. If I get a longer julet 3pin with open wires on the end.
So I am wondering how I connect them ?
I bought them from Fiido. They are a matching couple for the L3 bike. Would I wire the green and red together ? Or would I wire either the green or the red one or the other with one of the brake wires ?
I have a controller. And on the controller is a jst-sm 4 pin connector for both the brakes and the throttle together. 2 are for the brakes and that leaves 2 more pins which are of course for the throttle. But, the throttle has 3 pins. I dont have a multimeter and I have never used one. So,, if I switch the pins around to figure out which pin goes where. Could that harm my bike in any way ?
I had no idea that throttles have levels depending on how hard your thumb presses it... I’ve been pressing the throttle so hard no wonder the battery dies
Hi. Your advice please. Samebike L026 350w motor. After about 10mins ride lose (thumb) throttle power. Sometimes occasionally returns. When starting from rest again similar situation. Thankyou.
Do you know how can i run a mosfet irfz44n with this throttel?
My thumb throttle wire snapped but wires are so small would I need to just replace it?
Do you install throttle on emtbs
Hi , my aventure throttle only grabs at eight miles an hour, half the lower speeds are missing, should this be like this? Its made by aventon Thank you in advance
So, and if lcd display have hall wire its using for connection signal wire?
I have female plug in, how I get thumb T for my bike
Now I want to power my ebike with a bunch of bananas.
But if throttal volt from 0.8v to 3.6 v is it ok or not thanks
Can I use this thing on a ride on 12v lead acid battery.ATG?
So it's a potentiometer
I need help reconnecting my ebike. Could you help me?
what i want to know is, can you just connect the signal wire to the positive wire?
just to get home, like today my ebike has stopped, if i knew ii could just connect the sig to +
i might have been able to get home, with no throttle control ofcourse.
That's my question
@@truth.speaker oh my friend, i know what is the situation now, you need a button battery which is 5volts, you then connect 2 of the 3 wires to each side of this battery, thn you hav throttle. since then ive moved on to a gas powered china doll engine for long range!!!
I had a feeling they are magnets
Is there a way to bypass it with a button
Help my scooter controller has green, black, red, gray, orange. The new throttle LCD and has red, black, green, blue and yellow. Red to red, black to black green to green...... gray and orange? And blue and Yellow?
Wish you knew/explained how to connect that 5 wire display/switch throttle. The blue&yellow wires have me stumped
By any chance have u figured out what to do with the blue & yellow wires yet. They got me stumped
The blue, and yellow is for the ignition, or Power locks...
Hi, please, I replaced pedal assistant sensor with a throttle on my ebike and it not working. How do I fix the issue.
The controller doesn't have separate wire for throttle connection.
Greetings from Nigeria
Someone please show how to do an install on a bike that does not have one....
Is it waterproof
how to connect simple thumb the three wires black green and red on controller six color display socket red black white green brown yellow
Hi I have a Ktm e-xc which has a really long throttle action is there a way of making it shorter (less movement to full throttle)
Quick turn throttle
How too bye this
My throttle is not engaging my motor. Wiring is correct. Brand new bike, motor and controller are good. Any suggestions?
If it isn't working still, battery voltage?
great video , my gf wants to know where she can get a banana like that one.
Can you use this throttle in a 24v or higher scooter?
Maricel Simpauco every controller sends five volts to the throttle regardless of the battery’s voltage.
@@ballaratebikes287 I have a great question for you, I am interested in a twist throttle that starts you off slow, because I notice that all the cheap $15 twist throttles that I a have used, knock you off the saddle as soon as you barley turn it to its minimal activation point, I am looking for a throttle that starts off very slow and gradually starts accelerating to full speed. Please refer me to one either through amazon link or a model and model number, I will subscribe to your channel upon you response. thanks
Sir the second throtlle which has 5 wires please tell me how to connect this type throttle to 24v 250w speed controller....
Sagar Choudhary please ask your supplier. Anyone who supplies goods without support needs to be held to account.
MAGNETS. HOW DO THEY EVEN WORK
Hey are you on insta I need to ask for advice please
☠️ I've been experiencing extremely dangerous episodes of the motor not stopping as soon as I turn the throttle , related to high humidity conditions ! I think it's because the humidity increases conductivity of the hall sensors in the throttle . can you recommend a good throttle ? I think the manufacturers are going to have to make them water proof. I experienced the same issue with a different throttle , battery and controller. just using the bike after a rain storm is enough to cause the issue. We must have a throttle will a switch to cut power ! ☠️ Also stop using hot glue on the Hall sensors ! It melts were I live ! And make the throttle not Fall apart so easy , and they need to be made with softer grips or made to accept normal grip's.
Stop copy and pasting this
warninggg i copy your face and paste in google 👍🏻
Haha!! Banana! LOL!!
I thought these were potentiometer based... turns out that there is more than 1 type...