2.1 Bluetooth speaker build part 1 // Kerfing plywood
Vložit
- čas přidán 29. 08. 2024
- 2.1 Bluetooth speaker build part 1 // Kerfing plywood
Part 2 coming soon.
Parts used:
Subwoofer: amzn.to/2Dl2qBM
Front speakers: amzn.to/2Ds1ijh
Amplifier: rover.ebay.com...
Power supply: rover.ebay.com...
Switch: rover.ebay.com...
Camera gear:
Nikon D5600 body amzn.to/2CmNsLd
Lens 50mm amzn.to/2CRpKYx
Lens 18-70mm amzn.to/2CT9vu9
Samsung NX300 amzn.to/2lTrl7Z
Microphone: amzn.to/2Co01G2
Tools:
Makita Impactdrill: rover.ebay.com...
Makita Drill: rover.ebay.com...
Makita Charger: rover.ebay.com...
Holzmann Table saw: rover.ebay.com...
Dewalt Mitre saw: rover.ebay.com...
Makita Router: amzn.to/2qpIhbA
Hole punch: rover.ebay.com...
Bosch jigsaw: rover.ebay.com...
Scheppach belt sander: rover.ebay.com...
Makita Drill hammer: rover.ebay.com...
Pocket holejig: rover.ebay.com...
Forstner bit: rover.ebay.com...
Router bit kit: rover.ebay.com...
Music: Sappheiros & Cash - Dear Candle
Love it, i actually did this on a much bigger scale making a hifi unit 1.8x0.5 using the kerfing method. I was actually thinking about doing this for a bluetooth speaker today and wholla here it is :) Great work again.
Thank you! :)
Excited for part 2!
I will upload it within 2days :)
Love The idea! Waiting for part 2!
Ooh, nice! I'm planning a similar build and was trying to think of some way to round the corners, this looks promising. 😊
+moghrid yeah, and it is not that hard
Amazing!! I didn't know we can do that. Thank you
'WE" ?
Very satisfying video and your masterpice work
Thx, part 2 coming in a few days, stay tuned :)
Beautiful work man, I can't help but think you should get your logo made into a brand and burn it into the ply, would look great!
David Mitchell thank you! :)
Well done Erik, amazing work. Can't wait for the 2nd part :)
+sahat keshiyev thank you
Fantastic!
Waiting anksiously for 2nd part
The finished piece is very pretty, I like the use of different wood, and the natural finish, rather than shining it up.
The kerfing wasn't done tightly enough in the beginning, probably could have done a few less cuts on each corner in order to get a tight fold with the slits.
How the hell did i miss the part of you kerfing? after doing a dozen kerfed projects, i just saw how you used water, heat and tape to get it into position, then glued. Great work. Normally i cut, spray the bended surface with water, glue, then bend into position, which i think is more difficult as the gaps fill quickly and attempt to fight you get it to the curve you need.
Stodoys has a very large project base.
People seem to like ur speaker build lots of views
Coolest box build I ever seen liked like always, and subs are going up good luck and keep up the good work👍
+Elevier Beltran thanks!
Check out Kirby meets audio. same kind of channel
Yeah I know about that channel :)
Me too, that’s how I got here:)
Awesome Job!
Damn the music is dope
Love your vids. Subscribed!
Hi, is there any application where the measurements of the woods appear?
What were you brushing on the wood as you were bending it? Also can a heat gun be used instead of a torch?
Yes Im sure a heat gun would be enough, I even think you would be able to bend it just using boiling water. I brushed on some hot water otherwise I would burn the wood.
Nice Just change that song
speaker must have clipped on the outside, but not from the inside.
Hur gjorde du falsen? Sågade eller fräste?
Runt högtalarna? Fräste :)
@@Erikdidit Menar inte runt högtalarelementen. Menar delen som du tillverkar i början av filmen. Du sågar spår i plywooden för att kunna böja plywooden för att få runda hörn på högtalarlådan. Sen har du gjort en fals både på fram och baksidan för att kunna fälla in front (baffeln) och bakstycket. Dom falsarna menar jag. Du hoppar över det momentet i filmen. 🙂
@@markojarvinen aha! Jo det gjorde jag med bordssågen innan jag böjde ihop allt :)
@@Erikdidit Okej. 👍 Så här efteråt, hade det varit enklare att såga ut falsen innan du sågade spåren för dom böjda hörnen? Menar att plywooden är ju inte lika sladdrig då. 🙂
Det har du säkert rätt i, minns inte vilket jag gjorde först :)
are you inspired by kirby meets audio?
Yes, at least my design
Beautiful.Because im making one speaker sooner or later.
GUARD THE TABLESAW
when will you upload part 2? :)
+Max van Andel as fast as i can, but I'm sure it will take at least one more week. Sorry for the delay.
intro music?
Sappheiros & Cash - Dear Candle
Really like the video, but waiting for you to cut your hand or fingers is ruining it for me. For goodness' sake, use a sled or something!
Don't make the cut if you aren't comfortable with it.
Your lack of guards and safety at all times just makes my stomach clinch. Love the work though...
Thank you!
Part 2 :
czcams.com/video/c8b84PxXC-w/video.html
Who disliked, hater