Tyrant Designs Glock 17/19 Gen 3 Lower Parts Kit Install Guide
Vložit
- čas přidán 13. 06. 2022
- Compatible Models:
- Glock Gen 3 - 17 or 19
- PF940C or PF940V2
Look no further than our Lower Parts Kit for Gen 3 Glock 17/19 frames and p80 pistols! Made to be a direct drop-in and within OEM specifications our parts kit goes through extensive quality control.
www.tyrantcnc.com/lower-parts...
This kit includes:
- Slide Lock Spring
- Trigger Housing Spring
- Trigger Pin
- Locking Block Pin
- Trigger Housing Pin
- Slide Lock
- Magazine Catch Spring
- Trigger Housing w/ Ejector
- Trigger Bar
- Connector - Sport
Thank you for the install video! I bought a lower parts kit, extended slide release, extended mag release, and new trigger from Tyrant Designs. I can't wait to put it all together!
I've purchased Tyrant Design components in the past. Absolutely love them! It's an affordable way to go Gucci or Beadazzle your build. Keep up the great work!
"Put the peace in the place where it needs to be".... If we knew where the pieces need to be we wouldn't be watching a video this makes it more confusing than it has to be.
Like the one I got from yall a while back, wish it didn't pinch on every pull, but it not doesn't hinder
No discussion of the orientation of the take-down lever? They do have different fronts and backs, right? I know the factory ones do.
Great video. Thanks.
All ready for the range!
Except for the part where you didn't put the mag release back in. 🤣
Would it kill ya to actually use the camera zoom? I feel like I'm squinting at every "piece" and "this"
I wonder if you could have filed this from space?
Thank you
You're welcome!
For anyone watching this video. the front takedown bar is actually directional. it DOES NOT work both directions.
there is a "hooked" end on one side, and the other is smooth. if its backwards your gun WILL malfunction.
Yes, the hook must face the rear of your frame
Yeah this video 🤔🤔
Your video is very informative, but it’s very difficult to see closely which way the springs and everything go. Maybe I would suggest a better camera angle directly over top of the items.
Thanks for the feedback!
Great informative video! So, do the 17 and 19 use the same kit?
They do not - www.tyrantcnc.com/lower-parts-kit.html
A roll of tape works at a frame support block for punching pins through
This is an elite tip.
Someone help,
Whenever I cock the slide back the trigger doesn't go forward (ready to fire)
Like it's supposed to.
What's the problem? Do I need to replace lower part kit?
P80 g17
With a P80 there can be a few things that may cause this. If you need help with parts purchased from us or are looking for more info on our lower parts kit, contact us at info@tyrantcnc.com
On the rear section of your G19, the triangle piece in the grip. the side will have a metal tab. make sure it has some spring to it.
many lower parts kits (the cheap ebay ones) dont come adjusted correctly.
also. the slide release with the little metal wire looking thing on it,
make sure that little metal wire is above the fat pin, but below the small pin.
if its above both itll be wedged into the metal guide
if you have any questions feel free to PM me directly. ive built a boatload of P80 G19/17
@@dannyipwn1203
Thank you greatly appreciated the tips, I will, try it out later this week.
@@dannyipwn1203
I took my g17 to a gun shop and even they couldn't figure out why my trigger won't reset. It's not my lower part kits or slide, it's been tested.
Very well done video, explanations are straightforward and the production value is fantastic. Thank you!
how to remove the serial number in lower receiver in Glock 17?
Just contact your local ATF office!
@@tyrantcnc that's a solid reply right there
The angles are off for the camera. Should be more close ups. Had to stop half way through the video as I couldn't see what you were doing. Need overhead cam view
We're elite engineers, but still not quite elite cinematographers.
Thanks for the feedback!
Can’t see any detail lol
You guys needed to zoom in so we can see what you’re doing.
Thanks for the feedback! We'll be re-shooting some of these to improve them and get more detailed close ups of the install.
Love the part where they just assume we know how to put a piece in and don’t show how to assemble the takedown spring altogether thanks for that👍
11:30 ish minutes
It is idiot proof only goes one way and if you can't figure it out we don't want you shooting a gun.
@@barefootbob1269 the most ignorant comment you could’ve put up…the video is meant to be and advertised as a full install guide and it doesn’t show start to finish….as I’ve never put together a frame from scratch you kinda need to see it from start to finish moron
@@ozsholin9933 Sorry your butt hurt But it does in fact show 99% of it but for that spring which when you look into the frame it will be very obvious how it goes.
@@barefootbob1269 not obvious for someone that’s never done it before guy…which is the whole point of the video
@@ozsholin9933 Sorry man not trying to be a dink. No that spring part is really simple there is a pocket it fits into and it will only fit in one way. Check out this youtube video in the search box type in Replacing the Glock Slide Lock Spring.
Wait does this make the weapon untraceable??
No, man... It's just upgrading the lower parts to more reliable ones. To make it "untraceable" (stupid name for it) you need to stamp in fake numbers into the serial number and then grind it down. Stamping in the fake numbers makes it so that if someone uses chemical wear to find the compressions from the original stamping in the ground metal, they will also see a bunch of fake stampings there as well.
Zoom in bro
Now i don't know how to install the spring he left behind. Some of us don't have one to start with from the factory. What a poor guide. At least show how you would install it. 12 mins in then reveals this isn't a complete install guide SMH
Thanks for the feedback, we'll be re-doing some of the videos to make them more complete and have some more specific steps.
If you use a hammer to remove Glock pins……😂
!!!!!!
Donate me a lower
God why does every gen 3 video suck so hard do people not know how to explain and record a video
Terrible
If you're gonna make videos to educate. Do a better job filming. Can't see 75% of what you did.
This is a terrible video. They don’t zoom in on anything that you’re doing whatsoever you give very vague instructions and you’re not showing anywhere near the amount of things you need to show to inform people of anything to expand their knowledge or understanding of what they are working with