How to Replace Blower Motor 09-14 Ford F-150
VloĆŸit
- Äas pĆidĂĄn 14. 11. 2018
- Buy Now!
New Heater Blower Motor with Fan Cage from 1AAuto.com 1aau.to/ia/1AHCX00322
1A Auto shows you how to repair, install, fix, change or replace a bad or broken blower motor. This video is applicable to the 09, 10, 11, 12, 13, 14 Ford F-150
This process should be similar on the following vehicles:
2009 Ford F150 Truck
2010 Ford F150 Truck
2011 Ford F150 Truck
2012 Ford F150 Truck
2013 Ford F150 Truck
2014 Ford F150 Truck
đ§ List of tools used:
âą 7mm Socket 1aau.to/oQC/1AXAA00017
âą 8mm Socket 1aau.to/oQC/1AXAA00017
âą Ratchet 1aau.to/o4n/1AXAA00016
Subscribe: / @1aauto
Check out our playlist:
Ford F150 2009-2014 12th gen: âą Ford F150 2009-2014 12...
Ford Auto Repair Videos: âą Ford Auto Repair Videos
For More Info visit us at 1aau.to/h/ajc/
â DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video. - Auta a dopravnĂ prostĆedky
â *Watch the Video*
â *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto
â *Do it Yourself*
â *Save Money*
Fantastic
I'm no mechanic but I was done start-to-finish in less than 20 minutes. Making sure I had the right tools ahead of time makes all the difference. Thank you!
+Michael Rogers Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-1AAuto-c
Great Video. My 2014 F150 Plati has same issue. Used all OEM parts for resistor, blower motor, Bussman 40A vinyl fuse, and relay and harness is good. Blower stuck on high. Upon removing the blower motor, there was a 1ââ cylinder piece of plastic inside the fan scroll rolling around. Stuck phone camera in there and took pics, but can not see or feel where this piece broke off. When I feel inside where the BM connnects, there is a plastic half moon shape door with 2 pivot points - this rotates about 60-90 degrees to allow airflow. The broken piece has hole/fitting with notchesâŠ.I am think it is a pivot point for this fan switch speed selector actuator- . Gonna search and come back with deets on what I find.
That back screw is, no joke, the hardest part of the job.
You guys are the best ! Especially this lady because she's very detail oriented and thorough and fast, the absolute best ! Thank you.
I think Iâve learned more from Sue than my actual instructors when I was in mechanic school!
Youâre fast. Took me a considerable amount of time longer than 7 mins
Thank you for the video. I am not mechanically inclined but was about to get it done because of this video. It was a pain to get the new one in but got it done no more blower motor sounding like a jet taking off lol. No to mention my dealership wanted to charge me $525 for parts & labor smh. I got the part for $170 saved myself $355 that is a lot of money with everything going on in our world today.
great video. Thanks for these. I was imagining a nightmare of twisting my hands into knots and this was super helpful.
Bought the blower motor for $100 bucks followed ur directions and saved alot of $$$ ! Thanks!
Very thoughtful for this video. Doing diagnostic on a 2012 f150 and determined it was the blower. Will definitely buy from you.
Replaced the switch and the blower motor. Not a technical job but a tight spot to work in.
I could not fit under the dash to undo the screws so had my son take care of them.
Glad to have AC and heat again.
Thanks for the video
I was thinking I may have to take it to the dealership to get it fixed. But this looked somewhat easy. Like u said, be patient. Great video like always.
this video made it easy for me to replace the blower in my 2014 Ford F150 and buying from you or saved me a ton of money. Thank you so much.
It' s much easier if you pull back the layers of carpet and padding, Dont need to remove them. Much less struggle
Thank you! I purchased a 2010 F150 XL two years ago. Got a great deal on it but always annoyed by a noisy blower fan. Just took it out, cleaned it (plastic wrapper was in there), and put it back. Noise is gone! If it ever goes out I know how to replace it quickly and cost effectively.
+Learning Developer Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-1AAuto-c
Awesome video! Anyone know what the carpet trim called that she removed from under the glove box first?
Just finished resistor and motor. Both work. Thank you.
Extremely helpful. Very detailed. Thank you.
Thank you gonna replace my blower this weekend. Great video đ
Great video!! Thanks so much for the video placement and quality. Your explanations are simple and to the point, and I love how you showed that you tried different tools. Well done!! Cheers from Innisfil Ontario Canada!!
Thank you for the great reply. We love to empower our customers by showing you how-to perform your own auto repairs while installing our high quality auto parts. Have a great day! 1aauto.com +LOUDROWDSTROUD
I just successfully completed this procedure. The aftermarket part works great! She makes it look a lot more easy in the video! I really had to struggle to remove the old part and insert the new part. There is no extra room! The 8 mm ratchet wrench for the far screw was key! Nothing else fit in that space.
+Justin B. Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-1AAuto-c
The dealership will charge you $400 just to do this. I know because I just had it done to me. Good thing I had a wrap warranty. Dealership mechanics are crooks.
This was very helpful! Thank you!
ok I will check y'all out next time for sure. I already had purchased my part. thanks for the video
+78 Stankin Lankin Thanks for checking us out and taking the time to comment. 1AAuto.com
Perfect video!
Sue always come through when I need to learn how to do something on my ford!
A1, can you provide a part number for that felt liner? I have a friend that needs that part for his truck. Thanks.
The short ratchet used at 2:12; I don't see a link for it. Never seen one like that before.
Perfect!!! Thanks so much!!!
This is great! Couldn't find anything close to this.
Took an hour but I dropped a socket in the body....GRRRRR! Good video. Thank you.
Thank you very much for posting this video! My blower was roaring and the shop couldn't fit me in before this weekend's single digit lows set in. I pulled the blower and found what looks like some sort of broken spacer/fastener in the squirrel cage. Put the blower back in and everything works just fine. I'm curious about what that loose piece is, though. Anyway, instead of $250 for parts and labor to replace my blower, I spent just $12 for an 8mm ratchet wrench.
You're welcome! Thank you for the feedback. +Mark Stoltzfus
That would be part of your recirculation door to your actuator
ETA for when these are back in stock on your website? Thanks for all the great videos!
Thank you. I watch another video for this and the guy must of removed about a dozen bolts, I did not want to do that. But when he took the blower fan out it had a plastic cap thing in it that he said was probably from the Recirculate door/hinge ... I watched YOUR video, and it showed a much simpler way to remove the fan. THANKS, oh and mine had the same plastic cap thing in it. I don't care about recirculate but NOW the noise/vibration is gone and all is well. IT was Hard getting that back bolt off and on, but patience was the key. * I used a small 8m wrench on the back screw, could only rotate about 1/4 at a time *
THANKS !
+James White Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
i nee o know if my f150 xlt 2012 uses or not a cabin filter cause is not under the compartment someone helpme please
So she did another video replacing the blower motor resistor. My clamp to the connector is broken. Can I order that part?
I need a blower motor, and I appreciate the mention at the end about your replacement ones having balanced squirrel cages. Do ALL your blower fans come balanced or only certain models? You have a LOT of blowers available but I don't see any mention of them being balanced or not, and all the pics I clicked on are generic and show none in the blades of the fan.
Awesome! Thanks much. This is the best video on YT for this. I didn't need a new part; just had some debris in the fan cage. Removed the debris, reinstalled the blower, all is good.
23rd 3ÂłÂłÂŸÂłe 3
I just replaced mine. Thanks for this video. I ended up going to Autozone and spending $200 for a Duralast one but HEY...IM IN HOUSTON AND ITS HOT...I NEEDED IT TODAY!! LOL
Can you see the evap coils with the blower out?
Very good instructions! Thank you. Chiltons should call you, because they don't have a clue!!!
+Gary Kipfer Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
Is there a way to tell which part is bad? Either the motor itself or just the resistor? Not sure on which to order from yâallâs website
Well done video!
Is this the same for the 2014 Ford Expedition, my AC just died out today. đ
Can a leaky quick connect cause air not to blow?
Do you have to take that felt off to get it out ?
Thank you so much friend!
+gaming with trigger Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
Thanks, youâre the best
EXTRA TIP! Take off the fuse panel cover on the side and pull the carpet back a bit once you're ready to take it out/replace it.
Great video đ
Thank you!!!
Great video would like to offer a tip on those push clips if you do it fast and not slow it will just pop right out rather than bend the mount
Can you get replacement ones anywhere u know of?
My 2011 150 works on 2/3 then shuts off after several seconds.. tried the resistor but still does the same.. 1 doesnât work.. 4 works for about 10 seconds.. ac air smells weird
My blower motor wonât go in no matter how much force I put in. Have any suggestions?
For years I called it a hamster wheel which I think sounds better compared to the design but if you donât learn something new your not doing it right. Great video đđ»
Put new front blower motor in 2011 Expedition. Cut a 1 x 2 4 inches long and jammed it under motor to support it, both during removal and new install, made it much easier. Also to remove and install motor I rotated motor about 180 degrees to get it up into opening and then turned into proper alignment.
Does this part work for a dual climate 2010 f150 platinum?
+Shannon Tuttle Thanks for checking us out! Yes, the product in this video is listed to be a direct fit for the 2010 Ford F150. Please let us know if you have any further questions, thank you!
Looks nothing like my 2013 Ford F150 XLT. There is no carpet piece for one, under the glove compartment there is just a black casing. I can't find a single video or diagram claiming to be for a 2013 that matches the duct fan layout for my truck. Everything works but it just started making a racket like the fan is hitting against something. Can anyone tell me if the black casing I am seeing is what I need to open up? I'm old but capable of doing this just can't afford to tear it down if it's not what I need to be doing.
A lot of time the motor sounds bad but it isn't, a part on the blend door breaks and falls in the motor, more common than the motor going bad.
I agree. I was on the F-150 owners forum with this problem (fan making a thump with every revolution). I was quickly educated about the actuator and pieces breaking off and falling into the fan.
im betting thats what happend to mine when i run the fan it makes a humming sound and at lower speeds it gets quieter on the humming
I just replaced the blower resister the fan will only work on high same thing ?? Could it be in the windings of the motor ?? Only 1 speed I hate to yank it for nothing u gave no symptons of the motor. Did it completely stop working/ ?? Is there a speed set up in side ??
Try checking the blower motor! +Dave Wilson
It's winter here and I had my heat on at the second setting. It stopped working while I was driving and now can only get it to push air at the fourth level setting, would this be a blower fan or something else?
blower motor resistor
Drawing too much amps if it keeps blowing then
My fan would stop working in the last two high settings. I bought a new blower motor resistor first to see if that would fix the issue and it did not. Will be trying to replace the blower motor next:/ hope it fixes my issue!
When installing, was there any worry about pressing too hard and breaking the cage?
Thanks for checking us out! As this part is plastic there will always be the chance of damaging it if too much pressure is applied. We would advise just to be careful when installing. Hope this helps you out! +cspears101
Perfect. I was able to fix it in 30 minutes
+Donnie James Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
I have a 2013 F-150 with a very annoying squeak coming from that far passenger air vent. I ONLY hear it when the air is on, and only on fan speeds 1-3. Iâm guessing replacing the blower motor would fix this? If the air isnât on, I never heard a peep. Thanks!
+Peyton Willoughby We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
Put new front blower motor in 2011 Expedition. Cut 1 x 2 4 and 1/4 inches long and jammed it under motor to support it, both during removal and new install, made it much easier. Also to remove and install, I rotated motor about 180 degrees so vent tube faced towards front of car, to easily get it up into opening, and then turned it back into proper alignment. Put wood support under it and fastened bolts.
I have a 2013 FX4 with the dual climate. I get an intermittent squeaking noise from it, and it goes away when I shut the system off. It does not get worse as fan speed increases.
Ya'll think this is the blower motor or something else? Swapping it out seems really easy.
Letâs go, Sue! đȘđȘđȘ
Make sure you buy this fan online every part store wanted $150+ vs $40-$120 online the $120 was a OEM motorcraft
Does anyone know where the cabin filter is on the 09-12?
From what I know they donât got one
Omg....I just replaced mine! Such an awkward position to work on. FYI anyone if you pull back the carpet and thermal pad the fan goes up in there easier.
+Fancy Name Thanks for the tip!
Is this what makes the hissing sound every now and then?
Thank you! Repair fixed! Pain in the butt whoever designed that setup thankfully it was only 3 screws!
Excellent video. Be careful when removing the three 8mm bolts though, and go reverse and forward a few times on your ratchet if they don't want to come out (they get caught in the plastic somehow). I broke the 8mm bolt closest to the fuse box on mine by using an electric ratchet on it at first, trying to get it out in one swing. Now the new blower motor is held in place by 2 screws only, as there isn't room to drill out the broken off / stuck bolt. What a crappy design!
thatâs ford for ya lmao
How did you know the blower motor was bad? Mine would intermittently stop blowing but would then come back on a few minutes later and not nothing. This is my guess.
Okay
Clockwise or counter Clockwise wise
Just replaced the blower motor controller With a brand new one and fan speeds (1-5) seem to work just fine, but, when you put it on the highest setting (6) the blower motor completely quits, could this be a problem with the blower motor pulling too much amperage. I.e. could replacing the blower motor fix this issue? 2014 F-150 Platnium
jerry church high speed relay
Sounds more like a resistor issue. Did you find the issue out?
@@jarretgrasse2599 Mine did the same thing, worked on all speeds except the highest setting until finally all speeds quit working, just replaced the blower motor resistor and it didn't help. Where is the high speed relay located?
Maza Mike should be in the fuse panel under the hood
@@mazamike this is my issue currently. Did you solve this problem?
This is the same thing for a 2014 f150
So Carla from Cheers left the bah to become a mechanic? What's a cah?
I'm guessing a stinky mouse nest is in the fan or the channel to the outside vent. Thx
Clean the evap coil while the blower is out!!
Just replaced the resistor to no avail, I have no idea what I'm doing or what I'm looking at, but I hope this worksđ€Ł
Just replaced mine and it sounds louder than the air coming out of the vents. Like a whirling sound. Not as quiet as original part
My fan will not come on at all is this the part that needs replaced? 15 degrees out I need my windows defrosted
+Kristi Burr Thanks for watching! It could be a dead motor, but it could be other issues like the resistor or wiring.
is it me or its litteraly the same blower in the S197 mustang ?
Thanks.
+@mortneff438 Thanks for checking us out. Shop for high quality auto parts on 1AAuto.com:
1aau.to/m/Shop-1AAuto-c
Question for anyone. Whenever I turn my heat or AC on, the whole truck starts to shake when the fan is running. Anybody know if replacing the blower will fix my issue?
Mine started making an awful rattle yesterday. I watched this video, pulled blower out, found a plastic part broken (other website said it was non essential - fingers crossed), removed it from blower, put blower back in, no more noise/rattle.
FYI... You don't have to remove the panel as it doesn't provide any more access. I also did it with a regular socket wrench, a 45 and an extension.
+Keith Strang Thanks for the feedback!
My replacement blower had a broken fan when it arrived. Sorry to say that A 1 Auto did not seem to help me with the return. I purchased another blower for less from a different company.
Good video, I completed this project from the video, lemme just tell you Ford has the absolute worst engineers whoever decided to put it in this position, had me cursing at myself for an hour
what exactly does the blower motor do does it let the air come out softly or when you turn it up to four it comes out more rapidly?
Itâs going out
It controls your fan speeds
Clink on da link!
+Phack Em Thanks for checking us out. Shop here for high quality auto parts: 1aau.to/m/Shop-1AAuto-c
That accent though....
New Orleans?
Dealership wanted $445.00 to replace........Thanks
Parts are always out of stock
+B T We try very had to get our parts back in stock as soon as possible. Please check back again soon.
ECđâ€WAX,
Guys this is alot harder than the video shows i really had no way to get a tool on the back screw so i had to use a universal socket because theres no room to get to it and it turned into a 3 hour job and my advice people let a mechanic do this itll save you alotta physical pain