How To Replace Wiper Arms 04-09 Audi A4
Vložit
- čas přidán 30. 11. 2015
- Shop for New Auto Parts at 1AAuto.com 1aau.to/c/24/4/windshield-wipe...
1A Auto shows you how to repair, install, fix, change or replace a damaged, bent, or failing windshield wiper arm. This video is applicable to the 03, 04, 05, 06, 07, 08 Audi A4
This process should be similar on the following vehicles:
2004 Audi A4
2005 Audi A4
2006 Audi A4
2007 Audi A4
2008 Audi A4
2009 Audi A4
🔧 List of tools used:
• Flat Blade Screwdriver 1aau.to/oSF/1AXAA00013
• 16mm Wrench
• 16mm Socket 1aau.to/oR7/1AXAA00015
• 2 Jaw Gear Puller
• Ratchet 1aau.to/oWb/1AXAA00016
Subscribe: / @1aauto
Check out our playlist:
Audi A4 2004-09 3rd Gen (B7): • Audi A4 2004-09 3rd Ge...
For More Info visit us at 1aau.to/h/acI/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video. - Auta a dopravní prostředky
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto
√ *Do it Yourself*
√ *Save Money*
Great explanation - thank you
Thank you for the video i have the same car 👍
You're welcome! +Julio Rodriguez
Where can I find a 2 Jaw Gear Puller? Thanks
Hi! I'm Mr. Thusharapriya Perera from Sri Lanka here again and my question for you all responsible and accountable persons is that what is the actual size of the two - jaw bearing or otherwise gear puller which you have been employed to remove the stubborn and stuck wiper arms from its respective shafts in this CZcams video of the wiper arms removal and replacement of Audi - A4 saloon or sedan? Furthermore, the reality is that it is difficult to get the use of a two - jaw puller which has a greater jaw thickness and greater in size with the small recces in the wiper arm fitting hole on the windscreen lower portion and the two - jaw puller must be 3" inches in jaw reach or length to get done the job or task effectively and efficiently. I would like to think you may reply or respond positively, comprehensively, and on a timely manner for my matter or concern above clearly mentioned. I would also like to wish you all the very best for your future endeavors and best wishes or kind regards from Mr. Thusharapriya Perera here from Sri Lanka. See you soon or later with another automobile repairing fruitful video until then good - bye. Thanks a lot.
Whats the pull or pull arm thing
where I remove right nut arm will not release.
+raymond ramirez Thank you for watching. You will need to use some force, or a prying type tool to release this. After sitting so long in the one position these tend to be frozen temporarily in their position. 1aauto.com
Hey, in the video it says you need a 2 jaw puller after you take the nuts off.