How To Replace Top End on a Yamaha Moto-4

In this video I take you on a step by step guide on how to put a fresh piston and rings in your Moto-4 200. I try to cover everything that you may run into when doing this job!
If you like what we do here at Toy Shop and would like to support us here on the channel then be sure to check us out on Patreon! www.patreon.com/Toyshop9665?u...
Below are affiliate links that will also help the channel out if you click on the link and make a purchase!
Valve spring compressor: amzn.to/3Efyp7N
Valve suction cups: amzn.to/3xwiuhV
Feeler gages: amzn.to/3ka00AF
Slide hammer: amzn.to/3VA34CR
Piston Kit: www.ebay.com/itm/401620276373...
Gasket Kit: www.ebay.com/itm/115319802043...
Intake Valve: www.ebay.com/itm/195388896080...
Rocker Arms: www.ebay.com/itm/234189206032...
Motion Pro Tools to make your life easier on this job
Valve Adjuster Tool: www.motionpro.com/product/08-...
Valve Seal Tool: www.motionpro.com/product/08-...
Visit us at www.toyshop9665.com to see what we're up to and to check out everything Amsoil has to offer!

[@timothytoy1191]

Good explanation! Very helpful.

[@michaelrathman7305]

Great video love the detail

[@jacobyork9536]

Great video man

[@fomoco1454]

Great detailed video man!

[@ToyShop9665]

Thank you!

[@isaacruiz7834]

great video 👍🏻

[@corymacdonald383]

I'm having trouble with the big o'ring on the bottom of the cylinder. I squeezed out and ruined the base gasket. It doesn't seem to have enough room.

[@ToyShop9665]

Did you get it figured out? Sorry just saw this. I don’t remember having this issue on mine 🤔

[@corymacdonald383]

​@ToyShop9665 I bought a smaller o'ring going to try it again. The parts diagram doesn't show an o'ring on the right rear head bolt hole, but it looks like it takes one. I have to do the valves and seal too, just waiting on parts.

[@bradleyhayes2727]

Would love some tips to get mine redone

[@ToyShop9665]

I’ve got lots of videos to help tackle a lot of different issues on these! Check out the playlist!

[@baileyrivers1772]

I can not get my cam bolt to loosen up to get it out Any tips would be great!

[@ToyShop9665]

I just gave her the ugga duggas and it came off. Make sure the timing chain adjuster is still installed because putting an impact on it isn’t the most ideal thing to do and that should help eliminate some of the unnecessary torture to the chain and sprockets. Also make sure you’re going lefty loosey. If you don’t have an impact maybe stick a screw driver in the sprocket teeth and let it come around until it binds under the chain and the use a ratchet. I wouldn’t use an impact on it this way though.

[@bobhemphut4011]

How much of a bear was the Allen heads for the exhaust ? Mines superrrr tight

[@ToyShop9665]

A lot of times they will seize in. I had to use vice grips to get mine off because the allen head was stripped out already

[@ngoose511]

How similar is this to a bear tracker?

[@ToyShop9665]

That I have no idea. They’re all pretty similar but I know the timing chain adjuster is different. Flywheel probably is too

[@vernonfale9135]

Bear tracker has, same basic engine design, only difference is flywheel and chain adjuster. Bear trackers have an auto chain adjuster.

[@ThePaparue]

Why didn't you set the end gap on the piston rings?

[@ToyShop9665]

They were good enough. 🤷🏻‍♂️ I didn’t have to

[@donnierowland3677]

They are preset

[@randomlystupid]

Thanks 💯