Video

My sproket ie stuck

You can offset the spacers on the deepwall impacts to give it a little more front to back stability.

Could you give the sizes of the stickers I would like to remake them myself?

You can buy a file cleaning hand brush. It is flat (maybe 2", 50 mm wide) with many properly spaced short (1/4" tall) metal "hairs" standing up and these hairs fit into the grooves in a file. Works great on fine and coarse files. Drag the brush across the file ata slight angle in the direction of the grain of the file. You may even feel the brush as it glides across the file cleaning the low area of the file (between the file's teeth). A couple passes then move along the file to a new section until you cleaned the complete file or the dirty area.

Hello there I have a question? I have this same atv and my question is of the rims, would the Yamaha moto4 warrior aluminum rims fit on your or my atv??? Please let me know. Cause I want restore my moto4 by updating its look too.

Great vid best I have seen

Brilliant, thanks for the tip!

Old school big bore she's tierd

Hey man I lost the spring for one of the lines to the carb do you know where to get one

I have a 1990 Polaris Trail Boss 350 4x4, I need to do this very fix... won't retract. I love these old machines, but sometimes working on them is a test of a guy's patience.

Which carb did you calibrate the syncpro to? The closest one to the handle bars or the one where the carb is below the seat?

I'm having trouble with the big o'ring on the bottom of the cylinder. I squeezed out and ruined the base gasket. It doesn't seem to have enough room.

You’re a life saver man! Great video

Great! I have installed a reverse case on my Skidoo Formula czcams.com/video/nLHg05zDGzI/video.html

Great video. My 4 stroke 03 trailboss 330 uses a different system. It had a diaphragm on a spring and has a flap that opens. It also doesn’t appear I can take out near as many jets.

Where can I get that part at

It was a good time can't wait till next year

I just bought a new caliper with pads installed for 45$ and put it in took maybe 20 minutes

Awesome video!! Is there any chance you know where the VIN number is located? I have the same bike and can not find it. Thank you!

I just had front sproket catastrophique failure, destroy case, water pump ,clutch push rod in pieces and just realize looking at pictures that the shafts end is destroyed was beat up by the sproket and still in the front cover case . RiiP 2007 Yzf600r with 36k 😢😅 ...

so my bike wen going lurches like a skip would this be it

What did u do to remove the old spray paint thanks!

That old bike brings back some memories. We have one on the farm. It was very reliable and would go through just about anything without getting stuck It would pull a loaded hay wagon as long as you could get traction That super low would pull. We still have it but it's sitting outside in the graveyard probably seized at this point. It had a rough life. It definitelyowed us nothing.

I assume its the same for the 1400

I’m thinking I might just use the pull start lol don’t know

great job!

Hey good job! Where did you find that seat cover. Also a good way to patch up the seat foam is with carpet foam. 👍

thanks, ive just replaced the timing chain on my tw200 (its the same engine) I didn' t remove the top sprocket though, just sort of derailed the chain off of it after removing the tensioner it worked fine, I put the new chain back on the same way👍

Seems like having a 3D printer would pay for itself.

Is there No gasket for the middle drive gear?

So the flywheel is located on the key way on the shaft?

25:21 bruh.... Your neighbors dont want to see you do that in the middle of your yard.

After rebuild was done did you have to do anything to prime oil injection? or maybe mix first tank of gas?

Another part for this series! Excited to see you back on this project

How many turns did you do around the white plastic piece and the coil??

Where can i find adapters for the sync ports on the carb ???

I can not get my cam bolt to loosen up to get it out Any tips would be great!

Awesome! Did your new piston hold up in your old bore is the machine running today? Also did you ever do a compression test after this top end rebuild was done and machine up and running? Im debating whether to get mine bored out or just change out the piston i have minor cylinder wall scuffs on my cylinder..

Thank you so much this was easier than I thought! Very helpful

any chance that you could give the link to the kit?

Thanks 💯

Thanks for the video. Helped me clean the carb on my 2005 Rubicon. Almost identical disassemble and reassemble.

Organizers just make a nice color box look so full 🔥🔥 this dope tech!

So are the holes on the flywheel to put the puller bolts in metric? Are the bolts that came in that harbor freight kit metric? I would have guessed their imperial?

I have a 1990 Polaris trailblazer, I was riding it full throttle and suddenly I could hear the intake sound over the exhaust sound if that makes any sense. It slowed down and died and now it’s got 60psi compression. Gunna give it a top end rebuild thanks for the video

Thanks for the great video and all of the tips to make it easier to accomplish.

I have that exact fourwheeler. Probably use it at least 4 or 5 times a week. Very reliable!!!!