Deck belt issues 101. Common reasons why deck belts fail.
Vložit
- čas přidán 17. 07. 2024
- In this video I go over the most common issues I see with deck belts on residential and Commercial mowers. Keep in mind these are not the only reasons you may be having deck belt issues these are just some of the most common issues and causes that I see.
Thanks for watching and don't forget to subscribe!
Residential mowers deck belt keeps coming off deck belt breaks, deck belt snaps, lawn mower deck belt. - Auta a dopravní prostředky
Wow, good catch on that rusted surface wearing out the belts.
Neither lender nor borrower be. I don't have any more friends, but all my equipment is in top shape.
Great video. Ive learned some of what you covered the hard way. Plus i learned something new about the pulleys. Thanks
This was tremendously helpful. Thank you
Very well explained and great advice
Hoping people will learn and appreciate what you have done to help them save money and time 😊
Thanks!
If the pulleys are rusted, you can use a wire wheel on a battery impact to clean. Those chunks of metal were too much on the ones you showed, so good catch in replacing them.
We have a JD 777 Zero Turn mower it is a 2006 and I believe we have replaced the deck belt once. But the mule drive belt has been replaced numerous times, a little stick or pine cone fragment will lodge in a pulley. While it is running it does fine but if you shut it off and then start up again when you engage the blades it will pop the belt.
Also slow down for fire ant hills and heavy clumps of grass.
The one thing I have thoughts on this matter is blades need to be replaced/ and keep them Sharp
I’ve only had to replace one belt and that was because it put it back on wrong and didn’t get it behind the belt holder so it rubbed the belt till I could smell it.
Nice video your opinion on blade engagement half throttle or full? Been told engaging at full throttle puts a lot of tension on the belt too
i ran my husqvarna riding mower for 10 minutes when I heard some rough noise, turns out one of my blades was not tight for those 10 minutes. I tightened it again and about 5 minutes later the belt shredded. it was a belt only a couple of years old. Could the out of balance blade have caused issues with the belt?
Mechanical Mind
I Can See That Spindle Brake Has Adjustment, It Should Be More Flat On The Spindle Pulley
Thats Why The Belt Has Marks On It
I actually noticed that myself while filming this video 🤣. I almost mentioned it but I try hard to make the videos short and to the point. If not I'll ramble on and the video will be 18 hours long. Thanks for watching 🍻
Hey thanks for the video. Do you have any recommendations for grease gun? My grease gun always get stuck.
Lincoln brand is what I use and like the best
I have a brand new 2023 s100 with 15 hours on it total. My belt fell off yesterday in the middle of mowing. I got it back on.no problem but when I activate the lever, it makes a loud screeching noise before engaging
The new S models are having some deck belt issues left and right.
Check out this video I just did about deck belt issues
czcams.com/video/8bwvkn9LdDs/video.html
Some belts are 15/20 years old when you get them
Look them over good for signs of age and return them if tiny cracks appear
I need to do a video about the new belt they are using on the S100s. Many of them have a bump in the belt on the outside. It hits the belt guide around the engine crank pulley and makes a loud noise. Sounds like the engine is knocking. I have to search through several new belts to find one that doesn't have a bump in it. Manufacturer defect
Thanks heaps. Question: my Belt is vibrating a lot and eventually throwing itself off. Hasn’t broke the belt yet, but is damaging the belt each time it comes off. Can’t find any reason for so much vibration
I would remove the deck to be able to fully inspect it. Vibration can be caused by damaged blades, sometimes wrapped up in the blades, or bad bearings in a spindle or belt idler.
When those things happen it makes it harder for the belt to turn whatever damaged pulley or spindle and that will cause the belt to jump of that pulley or spindle.
Also you most likely going to need to replace the belt after you have fixed or replaced the issue. Often times once a belt has gotten twisted or jumps off often, it gets damaged and will never preform right again.
Not sure what mower you have but this video should help regardless.
czcams.com/video/WIQG4FkWmWA/video.html
While spinning the spindles and idlers, you should not hear any noise or feel any roughness in the bearings.
👍👍
Will a bad belt cause heavy vibration? I replaced the blades and the belt jumped off after two passes around the yard. I put the belt back on and it still vibrating ver bad. Any thoughts would be greatly appreciated!
Hey Terry, the belt usually does not cause vibration unless it has a large chuck missing. Normally vibration on the deck is caused by a bad spindle or the blades. The blades might have something wrapped up around them or a blade might be bent or damaged causing it to be out of balance.
I recommend to remove the deck and spin all the spindles and idlers. In good condition they should spin smoothly and make no noise. Here is a video that might help
czcams.com/video/3S3XHxICmcc/video.html
@@Mechanical_Mind thank you very much for your response. I did notice that the pulleys were a little lopsided, or tilted. Is that normal?
@terrybrennan2534 That is not normal. You found your problem.