Installed New Blades and Still Cuts Uneven
Vložit
- čas přidán 27. 08. 2024
- Lawn mower will not cut even. How to straighten mower deck that is bent.
Installed a new set of blades and still cuts uneven.
Slide Hammer. amzn.to/3y2QmnX
Deck Leveling Tool. Stens Deck Level Gauge 750-442 John Deere AM130907 link; amzn.to/3y7Fd1I
Dude has more talent in a single hand than most their entire bodies
An actual right to the point video without the history of lawnmowers and origins of manufacturers. You get what you need and a perfect demonstration of how to do it. Best video ever.
Through the years you have help me so much with your videos. You saved me at least 600 to 700 dollars on this one alone. It took me little longer but I was able to straight up my jd deck also. Thank you sir, thank you very much.
Glad to hear! Thank you for watching my videos and happy they are saving you $$$
another way to check level, before removing pulleys, is to place straight edge across top of hub pulleys to see if they align one hub to the other.
I’d give you two thumbs up but …well you know.
Seriously, great video, here’s why:
1. No music!! Yes!!!
2. Excellent camera angles.
3. Clear explanation of what you are doing and why.
I just subscribed.
LOL! Thank you for the kind comment and supporting my channel!
second the no music! great video
Thank you! I've been working on my mowers for years and never saw this technique.
Its not pretty or easy but it will save you from having to purchase a new deck or even a new machine. Thank you for watching, the kind comment and supporting my channel!
Three years ago I bent the mower deck on my John Deere d130. They said there was no way to fix it and they wanted $1100 for a new deck. My solution to the problem was to take that $1100, add $1800 to it and get a Husqvarna zero turn with a fabricated deck. I still have the John Deere deck in the cellar, and now I know how to fix it. THANKS!
So traded one piece of junk for another? Haha.
Most things commissioned to be made for the purposes of profit will be of poor quality. Welcome to capitalism.
I bought my D130 new in the spring of 2015. We're almost into fall and my D130 still runs and cuts great and I've never did anything but routine maintenance. It's a great machine cutting it's 9th season so I'll have to disagree with the D130 bashing. It's the best mower I've ever owned
@@chuckiebrown1494 it's a good mower until you hit a small tree stump with it and bend the blades and the deck.
I'm bashing the repair people. I'd like to...
@@tomstepanowicz6191 I actually did hit a few things but was lucky enough that it's still straight.
i'M a 72 year old gal that still wrenches. So glad I ran into your videos - they are straight forward and easy to follow. So even I can do it LOL Thanks bunches
Awesome! Glad to hear. Thank you for watching and the kind comment.
I ran into this problem myself with uneven cuts. New blades didn't fix it. So I just cut uneven. Now I have new info. I'm going pull my deck. This is probably exactly what is wrong with mine. Thank you sir!
I hope this video helps with your issue and you will be cutting straight again! Thank you for watching and the kind comment.
Straight forward, good troubleshooting advice, practical cost saving discussion! I appreciate you taking the time to film and explain! Great video!
I’m glad it was helpful and thank you for the kind comment.
Thank you. This has been my tutorial for today. Thanks.
I'm glad it was helpful! Thank you for supporting my channel and the kind comment!
Not only do you know your doing you do it very well and better than most people with two hands. Very nice video showing how to save money. Thank you for sharing.
I appreciate that! Thank you for watching and the kind comment.
Thank you for the information.
I have the exact mower and deck.
I also have a 52 inch deck both with the same problem.
My fault I hit some old stumps. Mowing where I should not have been.
I'm glad it was helpful! Thank you for supporting my channel and the kind comment!
Thank you 🙏 so much. Any time I can save money doing things myself I try too and watching your channel is a blessing of knowledge .
I'm glad my videos are helpful. Thank you for watching them and the kind comment!
Solid DIY tips on doing it right and under budget! Keep em coming!
Thanks! Will do! Thank you for watching, commenting and supporting my channel. It is greatly appreciated.
There has never been a time that I’ve watched you and not been blessed. Thank you so very much, and again God bless you.
Thank you for watching and supporting my channel!
I've been searching how to find where it's bent. This is a perfect explanation
Excellent video tutorial! You taught an old dog a new trick! Thank you right on my birthday!
Happy birthday!
Best explanation I have seen on why the deck does not cut evenly. Especially since this is the deck I just replaced after 12 years. One tip on this deck if you have to replace it, it is cheaper to buy a complete deck through sales ($900), rather than a bare deck through parts ($1100).
Good to know! Thank you
Man am I ever glad I watched this video. I've watched several of your videos which gave me excellent tips as far as doing work on my LA130. Now this video is giving me ideas on why my Wheel Horse 52" deck is shaking so badly after I hit a raised patch of ground in the ditch by our house. It hit pretty hard and this may be what happened. I very much like your simple no nonsense approach to repairs rather then throwing a ton of money at the problem. Thank you
Check your blade hub shafts and blades. I’m sure one or more will be bent. You also may need a new blade belt due to; if the deck stopped turning when you hit the mound and the engine was still turning the blade belt, the belt can get a bad spot in it and that will cause a bad vibration also. Good luck! Thank you for watching and the kind comment!
@@JohnsonsSmallEngines noted and many thanks for the additional tips. I'll be 70 in a week so you are teaching an old dog new tricks! :) thank you
You got the job done. Without costing the customer much money. Looks great from my porch. Job well done. 👍👍👍👍
Thank you!
With new decks starting at 750 bucks and UP, it was a cost effective way to fix a bent deck....
Very clear and concise. Just subscribed!
I'm glad it was helpful! Thank you for the kind comment and supporting my channel. Please share my channel to help it grow. It would be greatly appreciated!
Awesome advice! Your directions were right to the point and easy to follow. I was afraid that I was going to have to shell out a lot of money to fix, but thanks to you...heck, I'm ready to give it a go.
Thank you so much.
I hope it helps straighten you out! LOL. It does take some patience and time but it’s a lot cheaper than buying a new mower deck. Also, check your blade shifts to make sure they’re not bent.
@@JohnsonsSmallEngines Will do 👍, and thank you, again. Like you said, it does (may) take some patience and time, but it's a lot cheaper than buying a new mower deck.
Very interesting 2 thumbs up on this video. Great advise on taking spindle out before the frame straightening. Excellent work.
I'm glad it was helpful and thank you for the kind words.
Thanks for the great video! I own a John Deere 285 that I have restored. I just purchased a mower deck for it and am trying to figure how to attach it. Your videos are very helpful.
Thanks I have the dame issue . ill wait till the end of the season when I clean and sharpen and scrape the deck . thanks
Its not easy but it works! Thank you for watching and the kind comment.
That was amazing! I would have never suspected a bent deck... Good job!
Thank you!
I know you’ve heard this a million times. You are an inspiration!
I hope this inspires people to realize how capable they can be with two hands.
Every project I encounter from now on will make me ask how would you do it. No more “ I can’t, it’s too difficult”!
Thank you.
LOL! Its all good. Thank you for watching my video and commenting.
Great job! He must have hit something really hard to bend the deck that bad! Thanks! 👍👍
Thanks Tony, I see this more than you would think. Most of the time it is from the cap on a water pipe or sewer pipe or stumps that grow in the yard, LOL
Lots of helpful information. Fortunately, I haven't had that problem. I have had decks get weak from rust. Cut it out, and weld new metal back in. Works fine.
I ran over a small cedar tree stump with my JD X33O 32" deck last year. The second time last year I tried to destroy that mower. Anyway, the second time, I bent both blades. After installing 2 new blades, I found out they were meeting in the middle, tip to tip. Ended up trimming about an eighth of an inch off each blade. Not kosher, but it was crude and effective. I've got to look each side again to see where I bent the deck.
I have come across aftermarket blades that would touch in the center but the old blades did not so I had to do what you did. As long as the deck is cutting good and grass looks good, I wouldn’t worry too much about it.
@@JohnsonsSmallEngines Thank you for the reply. I ground some clearance on one blade, used marker like dycum blue , them ground to match.
I sure am glad I found your videos. They are very helpful.
Hi Steve, Thank you for watching and commenting! I'm glad they are helpful. Please give the thumbs up, subscribe and tell your friends to help my channel grow. It would be greatly appreciated :).
Thanks!,never thought about the deck being bent.
It does happen. It is not a easy repair but it is cheaper than buying a new mower deck!
Thank you so much for the solid info. I need to look over my entire setup now after all the info you just dropped. This is how you make a diy video.
Hi Will, I'm glad it was helpful and thank you for the kind comment. Please give this video a thumbs up, subscribe and tell your friends about my channel to help it grow. It would be greatly appreciated!
Great videos, thank you. If you continue to teach everyone how to fix everything so well with these great videos you are gonna put your shop out of business !!!
Thank you! LOL:) I thought the same thing but still very busy:)
Another informative and well done video from Johnson's, thank you man, excellent work.
Thank you:)
This video kept me from having to buy a new mower deck. Thank you so much for a great video.
Hi Bill. I’m glad it was helpful and I hope you make out ok. It’s a little more involved but well worth not having to replace your deck. Please give this video a thumbs up and tell your friends about my channel. It would be greatly appreciated.
Excellent information and instructions. I am having the same problem. Now I know how to find and fix this without replacing the deck. Thank you very much sir I appreciate it.
I’m glad it was helpful and thank you for the kind comment. Please give this video a like, subscribe if you haven't already and share my channel to help it grow. It would be greatly appreciated!
Great information. Thank you for posting.
I'm glad it was helpful! Thank you for the kind comment and for supporting my channel! Please share my channel to help it grow. It would be greatly appreciated!
Well done. Many people will benefit from this video.
Thank you for watching and the kind comment.
Thanks. I have a pretty serious bend happening somewhere. I need some of those anti scalp wheels as well. I don't have those.
I really hope this channel does well and you can get a modular adapter for your arm so you can attach a bunch of different tools to it. Not only would that be totally awesome, it would definitely draw in a ton of views xD
Good luck!
John Deere makes
reenforing ring to bolt to top of the
deck.
Wow man been trying to figure out why my blades were not even.good job explaining what to do.Thanks
I’m glad this video was helpful and thank you for the kind comment. Please give this video a like and share my channel with your friends to help it grow. It would be greatly appreciated.
Thank you so much for this video! My mower is now cutting perfect!
Glad to hear! Thank you for watching and commenting! Please give this video a thumbs up to help my channel. It would be greatly appreciated.
Excellent video!! I was surprised how easily and quickly you could bent it back. Good job. Thanks.
Thanks T O, I’m glad it was helpful and thank you for the kind comment. Please give it a like and tell your friends about the channel to help it grow. It would be greatly appreciated! Thank you for watching:)
Great work you are very good
Thank you for the kind words William. :)
Thank you for the blade tip. I never really paid that much attention to them before. I guess I can check My deck by measuring it to see if it's level on all sides. I hit a root with the edge of my deck, But I see no difference with the grass after mowing. Great job as always, I almost always learn something or am reminded of something. So thanks again.
Hi Steve, You most likely did not hurt your mower deck when hitting the root. It takes a good hit and most of the time the tractor will stop dead in its tracks when the deck get bent. Thank you for commenting!!
Loved my little john deere. Its older than dirt but kept going until recently. Replaced all the belts, serviced it and all. 2 weekends of broken springs, thrown belts and lack of patts availability i gsve up and bought a new mower. 54 inch deck makes quick work compared to the little 38.
Really smart and great job! Never ran into the slap 🔨 hammer before and just ordered one. Have a Kioti tractor with 4 foot tires on the back, and this tool should be able to break the bead if needed. Nice work 👍 and thank you! 😄
I'm glad this was helpful and thank you for the kind comment. The slide hamm a nice addition to have for multiple reasons as you stated!
I cut my yard and walking trails for 20 years with a STX-38. I got a new S240 and the first time around the yard I hit a root. Bent the blade and the deck. My brother in law had a Bolens and got the S240 too. First time around the yard, he hit a stump and bent the blade and deck. We both had mowed our yards the previous week without.
I continued to hit stuff I never hit before. I replaced the deck cause I had bent it back into shape so many times the metal got fatigued and wouldn't stay straight. I got a Accel deck and the first time out I hit a root. It stuck so hard in the root I had to pull it off with my truck. And it bent the blades and deck. This deck is heavier and harder to bend back. A few weeks later I hit a stump and really bent the blades and deck. I am tired of buying blades and pounding on the deck. And I need a bigger hammer now.
I never bent a blade on the old STX 38. I bent the hell out of the deck (Black deck) over the years hitting stumps rocks roots, the blades would cut holes in it when doing so, it rusted and my buddy welded it back together multiple times, we beefed up the parts that would bend.
I was working on the STX as I still use it and noticed the blades are tucked up inside the deck quit a ways. HMMMM The blades on the new JD's are almost level with the bottom edge of the deck. Could this be why I used to bend the front of my old mower's deck and not the blades and deck, and now hit shit with my blades and consequently bend the deck??? I think it is a design flaw.
When I bend my deck back I use a chunk of wood on the opposite side of the hole cause it looks like it is bent all the way through. One side down and the other goes up.
Good tips. I've BFH'ed a few decks over the last few decades and in some cases welded extra steel to beef them up.
This was my favourite video on the subject, I flipped my deck over and one side of the blade was even with the other then the other side of the blade was over an inch higher. This proved it wasn't the deck or spindle and just a badly.bent blade. I hit a paver that was on my lawn a while back
Funny you mentioned that. I have a Cub Cadet with the same issue, both blades line up in the middle, same height, but if I spin the blade on the chute side 180 degrees it's a little lower than the other blade. If I spin it again 180 degrees it lines up. So it has to be the blade. If the deck was bent the blade would still be lower (out of alignment) even after spinning it 180 degrees and it wouldn't fluctuate in height like that. If the spindle was bent the height may fluctuate but most likely go from too high to too low on each 180 turn. Not lined up and then low. I replaced the blade and the new one does the same thing. I'm thinking the blade on that side is bowing a bit when I tighten the bolt. Nothing else makes sense. The cut looks fine so I'm not going to worry about it. I never hit anything that would bend the deck or spindle. I had an older mower that definitely had a bent spindle and deck at one point and the blades would never line up when I swung them 180 degrees, they remained equally out of alignment, until I replaced the spindle and fixed the deck.
I’m the least handy person on earth and trying to fix that…. I watch a ton of videos. You are great at talking it through. Felt like a buddy just giving me the run down. Keep it up!
Thanks Ryan, I'm glad my videos are easy to follow. Thank you for watching and the kind comment. I will keep them coming!!
One of my kids hit a stump and bent the end of one blade 90 degrees. Put new blades on and I’m getting about an 8 inch strip that’s high. This is definitely going to be my issue and you gave me the fix. Thanks
I'm glad it was helpful. When you take ther deck off, make sure you spin the blade shaft to make sure the shaft is not bent. A 90 degree bend is a bad hit. I'm sure you will need the "deck adjustment" in this video but also make sure your blade shaft is ok. If it is bent It may be easier to replace the entire hub bit it depends on what you think.
Best video I've seen on this subject...
Great video! Now I have a plan for this weekend to try and fix my uneven cut issue.
My son hit something with the cub cadet and not only did it bend the deck but it cracked the corner of the spindle. For the life of me I could not get it to cut even until I remove the spindle and saw the bent deck. I used a small air hammer and a heavy duty mallet with a piece of wood and it worked. Wish I would have seen yours earlier
enjoyable video, I love learning. Thank you!
I'm glad it was helpful and thank you for the kind comment
Very helpful. Thanks brother man.
I'm glad it was helpful and thank you for the kind comment. Please give this video a like and share my channel to help it grow. It would be greatly appreciated.
I have the same JD 42" deck. The crossbar under the discharge chute broke off, it slammed into the right blade, are now the cut is messy. Of course the stability of the entire deck is also compromised. Nonetheless, this video was a major education, starting with the blocks and the level pully analysis. Anything can be fixed. Thank you!
Thanks to my lawn mower angel!
JSE now I have one less question....neither the actual problem nor the fix is intuitive. I jacked my mower up the other day and the blades looked fine, as much as I can see. It's a seriously old Craftsman and as you know getting the deck off that thing is a pain in the butt. I had smacked into a protruding tree root that I thought I had taken care of. Boing! Got untangled and the mower cuts uneven forevermore. I never woulda figgered out the problem. Very sneaky! Your video sorta floated to the top this morning and ya just musta nailed it. Wonky deck. Wow!!! Thanks JSE! Ya done good!
Your fan over in Alabam,
Norm
I’m glad this video helped answer a question or two for you! Thank you for watching and the kind comment.
Thank you for your time the best explanation on these lawnmowers and why they don’t cut even thank you very much
I'm glad it was helpful and thank you for the kind comment. Please give this video a like/thumbs up, subscribe and tell your friends to help my channel grow. It would be greatly appreciated.
This is a cool video. Im going to diagnose mine tomorrow. Something tells me mine is going to be bent too lol.
Been having this issue with my Husqvarna and now I know what needs to be done, because I’ve replaced the spindles and blades and it still cut uneven and after watching this video I check where the blades meet and boom figured out my deck was bent. Thank you guys for this great video
I’m glad it was helpful and thank you for the kind comment.
I use a short level when I straighten the deck around the pulley's
If you weld a pole to an old spindle hub, maybe you could straighten these decks with leverage.
Awesome! I call it a slide hammer.
I have hit so many things with our mower and really need to do this.
It it a nice tool to have in my shop! Its not for everyone but its nice to have when you need it. Thank you for watching and commenting. Please give video a like to help the channel! Thank you for watching.
@@JohnsonsSmallEngines One of my older cousins when I was a kid had lost an arm in some farm machinery. He was a small engine mechanic for years afterwards.
Great stuff! Excellent point about the anti scalp wheels!
Thank you! I’m glad it was helpful and thank you for the kind comment. Please give this video a like and share my channel with your friends to help it grow. It would be greatly appreciated! Thank you for watching:)
Great job god bless
I'm glad it was helpful and thank you for the kind comment! Take care.
That’s awesome, thanks so
Much, been going crazy trying to fix my uneven deck
I'm glad it was helpful and thank you for the kind comment.
Genius!!! The kind of knowledge you have only comes from experience, that and you have a good eye and sharp instincts. All of this together is what we call talent. Along the way you've discovered things you'd never find in any repair manual, you ought to be writing them down and one day write a book. Your other talent is the way you explain things, you are a very articulate and effective communicator. I don't think you understand the value of what you know and what you do. I can tell you love what you do but one day your body will tell you it's had enough. A book such as I suggest would nicely finance your retirement. I don't know how far you went in school but you could have easily been an engineer. The men who built America didn't just attend the finest polytechs but were also blest with a gift for whatever engineering discipline they were schooled in. Today we call that thinking outside of the box, you may not know it but that is what you do. It behooves you to share this but there's no reason why you shouldn't profit from it. Every year that passes the floor is a little further away and a little colder, your knees will be the first to let you know. When that time comes, write that book. Kudos
Thank you for the very kind comment.
Very good video
I'm glad it was helpful and thank you for the kind comment!
Thank you very much and I have learned a lot, you are awesome man. Excellent teacher and demonstrator. Amazing how you solve issues with one hand, May God bless you Sir. Thanks a million.
I'm glad this was helpful and thank you for the kind comment!
Good video and to the point. Most owners don't have the know how on why you do not move the wheels. Every tractor I receive the wheels are totally to high. I try to explain to them that they are set for a reason and not to cut the lawn so low. I did want to mention on one of your other videos that I did watch a few times incase I missed something. I was stumped on the Husqvarna zero turn that has the parking brake within the laterals. I tried each time and cleaned up all the relays thinking that was the culprit. I replaced the solenoid, ignition switch, checked all the wiring for breaks, anyway I don't know if you can make a edit to that video to let others know about the occupant relay within the harness under the control panel. I decided to move that relay since it had the same color coded wires as the parking brake relays. The tractor started, but would not start again, but the relay became very hot real quick. I found one on line and installed it and still had no call back from the customer. I don't suppose that you have a video on a troy bilt tractor that won't stop moving forward unless I turn the ignition off? I have set the brake but still won't stop. I may have to put on a stand and see the wheels in the back after pressing the pedal and see what's going on. I hope it's not the tranny.
Excellent demonstration. I had never seen that before, so I learned something new.
Thanks Bob. It's not pretty but it is effective!
Simple and very effective.
Thank you.
You're welcome! Thank you for watching and commenting. Please give this video a thumbs up and tell your friends to help my channel grow. It would be greatly appreciated.
Brilliant! I'm sure that's what must be up with mine. Thank you for the great explanation.
I’m glad it was helpful. Thank you for watching and commenting. Please give this video a like and share my channel with you friends to help it grow. It would be greatly appreciated.
I appreciate & enjoy your informative videos. It's easy to follow you and understand your logic. Thank you.
Thank you for the kind comment and for supporting my channel!
Terrific work there! Thanks for sharing!
I’m glad it was helpful and thank you for the kind comment! Please give this video a like and share my channel to help it grow. It would be greatly appreciated!
@@JohnsonsSmallEngines Heck, I was impressed. Liked and subscribed young man!
I got a bad uneven cut and I suspect something along these lines. I just replaced the spindles and it does look like one is a little wonky when I spin it. I might have hit something but who knows. Good advice here and another tip to add to my toolkit. Before we owned acreage I only ever needed a pushmower. Now I'm changing blades, and spindles, leveling the deck, changing belts, and I'm sure more things to come. It's frustrating when this happens but it's a nice feeling to fix it. 😅
Outstanding fix and video presentation !!
Thanks Gerry!
Another great informative video. You must have known that I also had a bent deck. Thank You Again. ❤❤❤❤❤👍👍👍👍👍👀😎
I’m hope you can get your deck straightened out. Check out my how to on leveling the mower deck after you straighten it. Don’t forget to check the blade shafts to make sure they are not bent.
Great idea only thing I would do is warm the paint up with a heat gun so it doesn't get pinched and form rust where it was hit by pinching the paint you break the bond to the metal ... I rebuild my JD deck this past summer and never thought of this but I was lucky it wasn't bent I did replace the blades because they were finished almost worn through where they turn upward behind the cutting edge from just lightly grazing soil on a steep hill that I now landscaped to feather it out so it's not as bad...
Good advice all around thanks!
I’m glad it was helpful and thank you for the kind words.
BEST EVERY DIY VIDEO!!!! You Now have a new Subscriber. Very Helpful Video
Hi Marco, I'm glad it was helpful. Thank you for the kind comment and for supporting the channel!
Great video, thanks. You saved me $600 bucks!
Glad I could help! I hope it went or will go ok. Please give this video a thumbs up, subscribe and tell your friends about my channel to help it grow. It would be greatly appreciated. Let me know how you make out!
This is a great, useful video. We have a LA105 and getting an uneven cut. I checked tire pressure and leveled the deck but, still a bit uneven.
I’m glad it was helpful and thank you for the kind comment. Please give this a thumbs up and tell your friends to help my channel .it would be greatly appreciated.
I learned a lot from this video! Thumbs up and subscribed ! Thank you very much for posting!
I’m glad it was helpful. Thank you for watching, subscribing and the kind comment!
I'm not real sure, but may be able to be crafty and use some washers on the spindles to get it back close. However I do like your fix and your work. Thanks for the video!
Thanks for watching and sharing. What ever works!! It will save many $$$ not having to purchase a new mower deck.
Thanks so much for another great video! I've learned so much from you. Best wishes and happy holidays.🎄
Thank you! Thank you for watching and the kind comment!
Good work, never seen these done before.
Hi Tom, thank you for watching and commenting. It is fun but better than buying a new mower deck!
Awesome video. I just happen to have one of those old bead breakers.
Nice! thank you for supporting the channel! Please like and share to help it grow. It would be greatly appreciated.
Definitely a lot of great advice !
Great info, thank you.
I'm glad it was helpful and thank you for the kind comment!
Hello sir just seen this video. Now I can go and check my deck out too. I,ve seen your deck leveling videoand got that procedure down. Thinking that the deck was uneven, now tomorrow I'll take my deck off and see if it's bent. Great video!!!
Hi Ronnie, I hope you get it all figured out! Let me know how you make out. Thank you for the kind comment and supporting my channel.
@@JohnsonsSmallEngines I most certainly will. Thank you for your quick response.
Thanks buddy, makes diagnosing my issue a bit easier. I haven't identified if the blades are bent yet but I hadn't considered the deck being bent but considering I have had nothing but trouble with my troybilt pony (2019) I wouldn't be surprised. I gotta pop the deck of to replace the spindle brakes (yes they are already trashed, along with deck engagement cable broken the idler pulley broke free from the deck... due to vibration from one of the spindle bearings not having a tight/press fit in on of the spindles causing vibration that lead to the pulley guards cracking)
I will likely replace both spindles and blades ( I used some sleeve retainer compound in the interim to keep the spindle from vibrating as bad)
Anyways... My old MTD mower will be put back into service if I find a suitable engine since MTD has always been built to a price but sheesh I wouldn't wish one of these things on my worst enemy.
And to think I was concerned about the Chinese engine being a problem LOL
I’m glad this video was helpful but it looks like you have a plate full in front of you! Lol I hope everything goes well and your machine gets back up and running soon. Thank you for watching and the kind comment. Please give this video I like subscribe if you haven’t yet and share my channel with your friends to help it grow. it would be greatly appreciated
Great job with slap hammer
Hi William, It may not be pretty but it works well!
DUDE!!!! FANTASTIC Video!!
I'm glad it was helpful and thank you for the kind comment. Please give this video a like, subscribe and tell your friends about my channel to help it grow. It would be greatly appreciated. Thank you for watching!
Thank you i have a zero turn with new blades that dont cut right this will help me figure it out
Hi Marvin, I'm glad it will be helpful. Let me know how you make out.
Amen to taking spindle housing off 1st. Good advice...nothing like busting a corner out and destroying housing🙄
Hi Lori, I learned the hard way LOL.
Wow thanks I have an edge 48" 3 blade that has always left a strip.. I have not checked it yet but i bet dollars to peanuts that my deck is bent. Thanks a TON!
I’m glad this was helpful and thank you for the kind comment. Make sure you check your blades first to make sure they are not bent.