Aaron, thank you for your video. It helped me wire up my new headlight. Halo & headlight work great! I used heat shrinking tubing instead of electrician tape. When we receive my wife's ST ebike, I will setup her headlight too. My bad - I should of took photos of my tidy and awesome work. Thanks again. Much appreciated!
You initially got me started down the path of installing a better light, but there were many road blocks of failure. The light would stay on initially and then not come on any more. So, long story short I wound up installing a tiny 12v motorcycle battery. I didn't want to mess with the Lectric Controller. I have also installed a spare battery that's in the RockBros Bag also that will allow for extended travel. I wired in a on\off switch for the headlight and juice horn. The first one the headlight switch was faulty, so had to order another one. The 8,000 lumen headlight is awesome! The spare battery is a success, and the switch on the handlebars works great! Note: I didn't realize the 12v battery charger had a 6v setting besides a 12v setting. It was left on 6v and pretty much got fried. I ordered a much better charger. Despite all this, I'm not disgruntled about my frustrations and loses - it was a good learning experience and at the end I have a better bike.
Nice vid, step by step it’s very professional. 😝 I’ve been looking for a vid like this and was unlucky. You should do a Lectric series on the upgrades you do there’s very few to none videos of Lectric. 😊
Great video. Thank you. I'll have to check on this because my stock headlight sucks and I dont want to buy a rechargeable lights if I can install a brighter light . I couldn't just buy 1 because they was out of stock. But they had a pair of 2 so I bought them could I hook up both lights with using the same wires?
Good information, I just ordered. In the last silent part of the video I’m assuming that small blue wire is the one you tied into for the halo. Do you have a video showing that process for the install?
Correct, the blue wire for the halo only nothing more, this is the circuit that applies power for the display and backlight when the power is enabled, limit 500ma on this line!
Hi, Nice video but a few questions. I am buying a Lectric Bike. I ordered a $17 bright light on Amazon. Wonder if it will work like yours? Also, can I bend the bracket without heat? I dont have a way to heat the metal up except using my gas stove. I dont solder, can I use small wire nuts to affix the wires? I am hoping the lights are water proof incase it get stuck in a downpour. The light I ordered on Amazon is Leorx 12-85 volt, switchless. Thanks in advance for your assistance Sir.
To connect the wires use butt connectors that have shrink wrap. I bend wire all the time without heat. Also I carry plastic bags that cover my throttle,screen and switches for heavy down pours. Will do same for light
Will this work with the Lectric Black XP 2.0 and would it have issue with the controllers and what about the wattage on the Lectric XP 2.0, wouldn’t want to fry it. Or any light would work
Light works great, but once on it won't turn off unless you kill it by turning the key off. I'm wondering if the original light has some sort of chip to communicate with the display software? Just wondering.
Sounds as though you may have a defective controller, we have 4 bikes with these lights and never had any issue yet, but I've read about others having this problem sporadically.
@@jim5269 yes i just installed the same light without connected the yellow wire for the hallow. Tried the lights a bunch of times and worked great. When i connected the yellow wire to the blue wire, I turned the power ON and the hallow came ON, then I turn the headlights ON and after wouldn't shut off. Now I took off the yellow wire and still the lights don't turn off unless turning the key to kill power. Quick note, I am a car electronic technician so I have +20 years in the industry and sounds like that yellow wire blew the headlights switch circuitry. Should've done my own testing before connecting that yellow wire. Now i have to open the control box and see whats need replacing as lectric won't cover that under warranty!!!
@@jim5269 i have a feeling that because this bike was such in demand that they changed manufacturers and that some electronic components may have different specs. That light draws 1.5A which is alot so im guessing it overloaded a circuitry. Im just glad it didn't damage the whole brain box!
Yes, I would have a select switch between the 2 lights as I'm not sure the total load capacity the control can handle. If you use the battery itself without the control though, your good to go.
@@aaronseely2710 well I took the wire from the stock light and wired the new light. It worked wonderfully. Rode it 10 miles then stopped at a friends house to show it to him and it was super dim. Then it wouldn’t turn off at all except when I turned off the key. Weird right? And the rear red led stayed on as well even when the controller had it off. It the light back feeding somehow?
Having a problem with mine, the wire in which the headlight is plugged to, its almost as tho its super glued together, no matter how hard I pull, it will never come off
Is there a point/wire where I can draw 12-24v for a cell phone Qi wireless charger base/mount? iMESTOU Motorcycle Phone Mount Charger USB 3.0 Handlebar/ Rear-View Mirror Cellphone Holder with Aluminium Mount Base for 12V/24V Vehicles Compatible with 4.0-6.8 Inch Smartphones
After installing light I powered on with the arrow up button and worked ok. Second attempt light would not turn off unless I turned key. Everything else still works fine. Any suggestions
@@aaronseely2710 I bought a bike that had the halo light hooked up already, everything was working fine but then the lights didn’t work anymore, I saw that the wires came loose I figured it would be a simple as connected the red to red wire and black to black wire coming from controller to the light but it didn’t work. I had my dad measure the voltage and he said it was only reading 2volts, not sure why it worked before when I got the bike but now when I try to connect the wire it doesn’t work. Have any idea?
liked and subscribed! could you please go over the halo light wiring. instaled with just red and black wires. love the light output, but no cool factor! Please help..
Thanks for the walkthrough. Interesting way of stripping wires but that makes perfect sense what you said. Keep it up.
Aaron, thank you for your video. It helped me wire up my new headlight. Halo & headlight work great! I used heat shrinking tubing instead of electrician tape. When we receive my wife's ST ebike, I will setup her headlight too. My bad - I should of took photos of my tidy and awesome work. Thanks again. Much appreciated!
You initially got me started down the path of installing a better light, but there were many road blocks of failure. The light would stay on initially and then not come on any more. So, long story short I wound up installing a tiny 12v motorcycle battery. I didn't want to mess with the Lectric Controller. I have also installed a spare battery that's in the RockBros Bag also that will allow for extended travel. I wired in a on\off switch for the headlight and juice horn. The first one the headlight switch was faulty, so had to order another one. The 8,000 lumen headlight is awesome! The spare battery is a success, and the switch on the handlebars works great! Note: I didn't realize the 12v battery charger had a 6v setting besides a 12v setting. It was left on 6v and pretty much got fried. I ordered a much better charger. Despite all this, I'm not disgruntled about my frustrations and loses - it was a good learning experience and at the end I have a better bike.
How did you wire up a 12v motorcycle headlight? Don’t you need a converter or voltage regulator?
Thanks for the video sir... now I can upgrade my headlight.
Heyyy nice video on this light! You was the one I got the idea from when you first posted it on Facebook 👍🏼 my light is still going strong
Nice vid, step by step it’s very professional. 😝 I’ve been looking for a vid like this and was unlucky. You should do a Lectric series on the upgrades you do there’s very few to none videos of Lectric.
😊
Thank you for doing this. I copied your effort, everything is working fine.
Glad I could help!
I got it thank you sir!
legend
Great video. Thank you. I'll have to check on this because my stock headlight sucks and I dont want to buy a rechargeable lights if I can install a brighter light . I couldn't just buy 1 because they was out of stock. But they had a pair of 2 so I bought them could I hook up both lights with using the same wires?
Good information, I just ordered. In the last silent part of the video I’m assuming that small blue wire is the one you tied into for the halo. Do you have a video showing that process for the install?
Correct, the blue wire for the halo only nothing more, this is the circuit that applies power for the display and backlight when the power is enabled, limit 500ma on this line!
Do u think this work for my juiced scrambler?
Hi, Nice video but a few questions. I am buying a Lectric Bike. I ordered a $17 bright light on Amazon. Wonder if it will work like yours? Also, can I bend the bracket without heat? I dont have a way to heat the metal up except using my gas stove. I dont solder, can I use small wire nuts to affix the wires? I am hoping the lights are water proof incase it get stuck in a downpour. The light I ordered on Amazon is Leorx 12-85 volt, switchless. Thanks in advance for your assistance Sir.
To connect the wires use butt connectors that have shrink wrap. I bend wire all the time without heat. Also I carry plastic bags that cover my throttle,screen and switches for heavy down pours. Will do same for light
Will this work with the Lectric Black XP 2.0 and would it have issue with the controllers and what about the wattage on the
Lectric XP 2.0, wouldn’t want to fry it.
Or any light would work
This will apply to any bike that has the M5 controller screen system, the model number can be found on the rear of the screen or on the control box.
Could you wire the yellow and reds together so the halo and light come on when you switch the light on. So the halo is not always on?
I would say yes, as long as it doesn’t exceed the output limits of the controller
Light works great, but once on it won't turn off unless you kill it by turning the key off. I'm wondering if the original light has some sort of chip to communicate with the display software? Just wondering.
Sounds as though you may have a defective controller, we have 4 bikes with these lights and never had any issue yet, but I've read about others having this problem sporadically.
@@aaronseely2710 Thanks! Just my luck. I'll just install a two button switch for the horn/headlight.
@@jim5269 yes i just installed the same light without connected the yellow wire for the hallow. Tried the lights a bunch of times and worked great. When i connected the yellow wire to the blue wire, I turned the power ON and the hallow came ON, then I turn the headlights ON and after wouldn't shut off. Now I took off the yellow wire and still the lights don't turn off unless turning the key to kill power. Quick note, I am a car electronic technician so I have +20 years in the industry and sounds like that yellow wire blew the headlights switch circuitry. Should've done my own testing before connecting that yellow wire. Now i have to open the control box and see whats need replacing as lectric won't cover that under warranty!!!
@@jim5269 i have a feeling that because this bike was such in demand that they changed manufacturers and that some electronic components may have different specs. That light draws 1.5A which is alot so im guessing it overloaded a circuitry. Im just glad it didn't damage the whole brain box!
@@jim5269 until I take it apart and analyze everything its hard to say. I just unplugged the headlight for now.
Great video. I bought a 48 volt light and I want to wire it into my Xp. Can I keep both lights?
Yes, I would have a select switch between the 2 lights as I'm not sure the total load capacity the control can handle. If you use the battery itself without the control though, your good to go.
@@aaronseely2710 well I took the wire from the stock light and wired the new light. It worked wonderfully. Rode it 10 miles then stopped at a friends house to show it to him and it was super dim. Then it wouldn’t turn off at all except when I turned off the key. Weird right? And the rear red led stayed on as well even when the controller had it off. It the light back feeding somehow?
It is a DC 12v-80v.
@@rescuehoundemtd yep you should be good to go, Bike puts out 54 volts But I have yet to have a problem
@@rescuehoundemtd this sounds like a controller issue, was this with 2 lights being powered from it?
Having a problem with mine, the wire in which the headlight is plugged to, its almost as tho its super glued together, no matter how hard I pull, it will never come off
Is there a point/wire where I can draw 12-24v for a cell phone Qi wireless charger base/mount?
iMESTOU Motorcycle Phone Mount Charger USB 3.0 Handlebar/ Rear-View Mirror Cellphone Holder with Aluminium Mount Base for 12V/24V Vehicles Compatible with 4.0-6.8 Inch Smartphones
Anyone figure out the yellow wire to blue wire issue with the light staying on?
Can i connect white cable to red cable and it will work?
red cable from the bike is positive I believe
anyone know how to turn it on with the electric XP Lite?
your link to the head light is dead ok, hehe
I’m having a issue. How can I get in contact with you
What kind of issue are you having?
After installing light I powered on with the arrow up button and worked ok. Second attempt light would not turn off unless I turned key. Everything else still works fine. Any suggestions
I am having problem, how can I contact with u?
Shoot me an email, aaronaseely@gmail.com
@@aaronseely2710 I bought a bike that had the halo light hooked up already, everything was working fine but then the lights didn’t work anymore, I saw that the wires came loose I figured it would be a simple as connected the red to red wire and black to black wire coming from controller to the light but it didn’t work. I had my dad measure the voltage and he said it was only reading 2volts, not sure why it worked before when I got the bike but now when I try to connect the wire it doesn’t work. Have any idea?
liked and subscribed! could you please go over the halo light wiring. instaled with just red and black wires. love the light output, but no cool factor! Please help..
The halo is wired into the blue wire from the controller
Literally cannot get the wire disconnected and I'm going crazy
me too..