- 37
- 39 900
Aaron Seely
Registrace 27. 11. 2015
Installing lights on Lectric E-bike Halo edition
Small tutorial on installing and wiring halo led projector lights on Lectric E-bikes
link to the headlight
www.amazon.com/dp/B07ZKQG9GN/ref=cm_sw_r_cp_apa_i_.RPqFbWX3KEEJ
link to the headlight
www.amazon.com/dp/B07ZKQG9GN/ref=cm_sw_r_cp_apa_i_.RPqFbWX3KEEJ
zhlédnutí: 20 260
Video
Kayaking time lapse 7 2 17 Grand river park to Eastmanville
zhlédnutí 76Před 7 lety
Kayaking the Grand River from Grand rapids park to Eastmanville
Fun with the losi 5ive
zhlédnutí 43Před 7 lety
Speed runs and a nice flip with the losi 5ive, fully stock engine and muffler setup 29cc Thank you for watching!
Family RC outing with the losi 5ive, Xmaxx, Slash
zhlédnutí 67Před 7 lety
A fun family outing having fun with fifth scale rc
flying over higgins lake in winter with the yuneec 4k Higgins lake MI
zhlédnutí 111Před 7 lety
flying over higgins lake in winter with the yuneec 4k Higgins lake MI
Flying around lake Cadillac Cadillac MI
zhlédnutí 517Před 7 lety
Flying around lake Cadillac Cadillac MI
Aerial of Holland State Park winter DJI Phantom 2
zhlédnutí 3Před 7 lety
Aerial of Holland State Park winter DJI Phantom 2
Speed runs with traxxas spartan on 2s lipo Jenison MI
zhlédnutí 49Před 7 lety
Speed runs with traxxas spartan on 2s lipo Jenison MI
Flying DJI phantom 100 meters up in Hudsonville MI
zhlédnutí 10Před 7 lety
Flying DJI phantom 100 meters up in Hudsonville MI
Traxxas summit 1 10 scale climbing pulling speed in snow camera mount
zhlédnutí 35Před 7 lety
Traxxas summit 1 10 scale climbing pulling speed in snow camera mount
Watching the sunset with the Dji phantom 2 hudsonville mi
zhlédnutí 8Před 7 lety
Watching the sunset with the Dji phantom 2 hudsonville mi
Traxxas summit snow blazing fun 1 10 scale 5607L
zhlédnutí 45Před 7 lety
Traxxas summit snow blazing fun 1 10 scale 5607L
flying around hudsonville sports complex DJI Phantom 2
zhlédnutí 4Před 7 lety
flying around hudsonville sports complex DJI Phantom 2
aerial view of Hudsonville mi from 1000 FT with the DJI phantom 2
zhlédnutí 58Před 7 lety
aerial view of Hudsonville mi from 1000 FT with the DJI phantom 2
aerial view of showboat park and chesaning
zhlédnutí 48Před 7 lety
aerial view of showboat park and chesaning
Flying around the pier at Holland state park holland MI
zhlédnutí 43Před 7 lety
Flying around the pier at Holland state park holland MI
flying DJI Phantom 2 Drone in 25 mph winds top flight 115 meters
zhlédnutí 11Před 7 lety
flying DJI Phantom 2 Drone in 25 mph winds top flight 115 meters
Could you wire the yellow and reds together so the halo and light come on when you switch the light on. So the halo is not always on?
I would say yes, as long as it doesn’t exceed the output limits of the controller
Thanks for the walkthrough. Interesting way of stripping wires but that makes perfect sense what you said. Keep it up.
Having a problem with mine, the wire in which the headlight is plugged to, its almost as tho its super glued together, no matter how hard I pull, it will never come off
legend
anyone know how to turn it on with the electric XP Lite?
Literally cannot get the wire disconnected and I'm going crazy
me too..
your link to the head light is dead ok, hehe
Great video. Thank you. I'll have to check on this because my stock headlight sucks and I dont want to buy a rechargeable lights if I can install a brighter light . I couldn't just buy 1 because they was out of stock. But they had a pair of 2 so I bought them could I hook up both lights with using the same wires?
Is there a point/wire where I can draw 12-24v for a cell phone Qi wireless charger base/mount? iMESTOU Motorcycle Phone Mount Charger USB 3.0 Handlebar/ Rear-View Mirror Cellphone Holder with Aluminium Mount Base for 12V/24V Vehicles Compatible with 4.0-6.8 Inch Smartphones
Will this work with the Lectric Black XP 2.0 and would it have issue with the controllers and what about the wattage on the Lectric XP 2.0, wouldn’t want to fry it. Or any light would work
This will apply to any bike that has the M5 controller screen system, the model number can be found on the rear of the screen or on the control box.
liked and subscribed! could you please go over the halo light wiring. instaled with just red and black wires. love the light output, but no cool factor! Please help..
The halo is wired into the blue wire from the controller
Thanks for the video sir... now I can upgrade my headlight.
B! Terrifying a weeks old fawn with your Fwad dog!!! If that looks to you as if that baby is having fun, you should be banned from all animals everywhere!! How would you like for me to play with your baby like that? Loud, lunging, pulling to the ground, bouncing off of and nipping at her .. ..all of it with the hair standing straight up on the dog's back!!! Hint: your dog is out of control, viciously terrifying a young deer & _you_ are a dolt for not recognizing it! _Missed the_ _entertainment?!?!_ 🖕😕🖕
I didn't know Crystal Lake had corn fields.
Its surrounded by corn fields lol
The baby deer was adorable I also like that dog too!!
How adorable.
Nice vid, step by step it’s very professional. 😝 I’ve been looking for a vid like this and was unlucky. You should do a Lectric series on the upgrades you do there’s very few to none videos of Lectric. 😊
I am having problem, how can I contact with u?
Shoot me an email, aaronaseely@gmail.com
@@aaronseely2710 I bought a bike that had the halo light hooked up already, everything was working fine but then the lights didn’t work anymore, I saw that the wires came loose I figured it would be a simple as connected the red to red wire and black to black wire coming from controller to the light but it didn’t work. I had my dad measure the voltage and he said it was only reading 2volts, not sure why it worked before when I got the bike but now when I try to connect the wire it doesn’t work. Have any idea?
Anyone figure out the yellow wire to blue wire issue with the light staying on?
I’m having a issue. How can I get in contact with you
What kind of issue are you having?
After installing light I powered on with the arrow up button and worked ok. Second attempt light would not turn off unless I turned key. Everything else still works fine. Any suggestions
Hi, Nice video but a few questions. I am buying a Lectric Bike. I ordered a $17 bright light on Amazon. Wonder if it will work like yours? Also, can I bend the bracket without heat? I dont have a way to heat the metal up except using my gas stove. I dont solder, can I use small wire nuts to affix the wires? I am hoping the lights are water proof incase it get stuck in a downpour. The light I ordered on Amazon is Leorx 12-85 volt, switchless. Thanks in advance for your assistance Sir.
To connect the wires use butt connectors that have shrink wrap. I bend wire all the time without heat. Also I carry plastic bags that cover my throttle,screen and switches for heavy down pours. Will do same for light
You initially got me started down the path of installing a better light, but there were many road blocks of failure. The light would stay on initially and then not come on any more. So, long story short I wound up installing a tiny 12v motorcycle battery. I didn't want to mess with the Lectric Controller. I have also installed a spare battery that's in the RockBros Bag also that will allow for extended travel. I wired in a on\off switch for the headlight and juice horn. The first one the headlight switch was faulty, so had to order another one. The 8,000 lumen headlight is awesome! The spare battery is a success, and the switch on the handlebars works great! Note: I didn't realize the 12v battery charger had a 6v setting besides a 12v setting. It was left on 6v and pretty much got fried. I ordered a much better charger. Despite all this, I'm not disgruntled about my frustrations and loses - it was a good learning experience and at the end I have a better bike.
How did you wire up a 12v motorcycle headlight? Don’t you need a converter or voltage regulator?
Can i connect white cable to red cable and it will work?
red cable from the bike is positive I believe
Good information, I just ordered. In the last silent part of the video I’m assuming that small blue wire is the one you tied into for the halo. Do you have a video showing that process for the install?
Correct, the blue wire for the halo only nothing more, this is the circuit that applies power for the display and backlight when the power is enabled, limit 500ma on this line!
Do u think this work for my juiced scrambler?
Thank you for doing this. I copied your effort, everything is working fine.
Glad I could help!
Cute baby deer! Where's the mom?
Not sure, it was only here a couple days before moving on
Light works great, but once on it won't turn off unless you kill it by turning the key off. I'm wondering if the original light has some sort of chip to communicate with the display software? Just wondering.
Sounds as though you may have a defective controller, we have 4 bikes with these lights and never had any issue yet, but I've read about others having this problem sporadically.
@@aaronseely2710 Thanks! Just my luck. I'll just install a two button switch for the horn/headlight.
@@jim5269 yes i just installed the same light without connected the yellow wire for the hallow. Tried the lights a bunch of times and worked great. When i connected the yellow wire to the blue wire, I turned the power ON and the hallow came ON, then I turn the headlights ON and after wouldn't shut off. Now I took off the yellow wire and still the lights don't turn off unless turning the key to kill power. Quick note, I am a car electronic technician so I have +20 years in the industry and sounds like that yellow wire blew the headlights switch circuitry. Should've done my own testing before connecting that yellow wire. Now i have to open the control box and see whats need replacing as lectric won't cover that under warranty!!!
@@jim5269 i have a feeling that because this bike was such in demand that they changed manufacturers and that some electronic components may have different specs. That light draws 1.5A which is alot so im guessing it overloaded a circuitry. Im just glad it didn't damage the whole brain box!
@@jim5269 until I take it apart and analyze everything its hard to say. I just unplugged the headlight for now.
Aaron, thank you for your video. It helped me wire up my new headlight. Halo & headlight work great! I used heat shrinking tubing instead of electrician tape. When we receive my wife's ST ebike, I will setup her headlight too. My bad - I should of took photos of my tidy and awesome work. Thanks again. Much appreciated!
I got it thank you sir!
Where did you get the halo light for the lectric cop step thru. Chasam9498@gmail.com
www.amazon.com/dp/B07ZKQG9GN/ref=cm_sw_r_cp_apa_i_.RPqFbWX3KEEJ
@@aaronseely2710 is this a normal installation? Or do I need to splice the wires and a additional wire to the battery.
@@aaronseely2710 I got it
Heyyy nice video on this light! You was the one I got the idea from when you first posted it on Facebook 👍🏼 my light is still going strong
Great video. I bought a 48 volt light and I want to wire it into my Xp. Can I keep both lights?
Yes, I would have a select switch between the 2 lights as I'm not sure the total load capacity the control can handle. If you use the battery itself without the control though, your good to go.
@@aaronseely2710 well I took the wire from the stock light and wired the new light. It worked wonderfully. Rode it 10 miles then stopped at a friends house to show it to him and it was super dim. Then it wouldn’t turn off at all except when I turned off the key. Weird right? And the rear red led stayed on as well even when the controller had it off. It the light back feeding somehow?
It is a DC 12v-80v.
@@rescuehoundemtd yep you should be good to go, Bike puts out 54 volts But I have yet to have a problem
@@rescuehoundemtd this sounds like a controller issue, was this with 2 lights being powered from it?
Nice channel! Looking forward to seeing more from you. I recommend you google smzeus . c o m! It’s a handy tool to have when you’re trying to grow your social media, CZcams videos, website etc!!
Good job man, if you want ideas for yours, check mine out, over on my channel.
You guys are idiots.
Can't believe how stupid folks can be!!!
Hello I’m a researcher at WooGlobe and we’re interested in a potential paid licensing opportunity for this video with good offer. Please email us at Viral(.at.)Wooglobe(.dot.)com or reply me with email and I can explain further with more details. Thanks!
why at oakwood? man i live here XD