This applies to almost any year accord it looks like. I popped off my 91 hub thanks to your video! Thought it was a much bigger pain until I watched this.
Привет приятель. Это отличное видео! Все очень доступно объяснил и показал. Также стоит использовать немного медной смазки, по краям центрального колпачка, а также на посадочном месте для колеса на тормозном диске, чтобы колесный диск не прикипал и не пришлось стучать по нему ногой.)) Медная смазка не боится больших температур. Ты крутой механик, удачи тебе!))
Really good video, great detail and thanks for not kicking out from under the car 😅. I just need to see if this applies the same way when the car has drum brakes?
The screws do nothing really for us. More for the factory when they are building the car. It lightly secures the rotor while it's travelling down the line.
I swear to God. The detail that u provide is gold! A lot of people just install and skip steps etc.. U answered every question I had.
This applies to almost any year accord it looks like. I popped off my 91 hub thanks to your video! Thought it was a much bigger pain until I watched this.
This is one of the most detailed videos I've seen. Thanks 😊
Great video Brother - I've done both rear hub/bearings on my 04 accord while referencing this video. Well done!
You make great tutorial videos! Thank you! Al in Portland, Oregon
Привет приятель. Это отличное видео! Все очень доступно объяснил и показал. Также стоит использовать немного медной смазки, по краям центрального колпачка, а также на посадочном месте для колеса на тормозном диске, чтобы колесный диск не прикипал и не пришлось стучать по нему ногой.)) Медная смазка не боится больших температур. Ты крутой механик, удачи тебе!))
Thank you for uploading this video.
Nice video, a big help to tackle this repair - thanks.
I can't thank you enough for sharing this knowledge. GOD BLESS YOU.
Love the videos, would love to see a diagnose / repair of the F150 door ajar issue.
Very thorough. Thank you!!
Greatly appreciated! The small details were very helpful to avoid damaging parts.
Very good thank you for this helpful video
Good video, well produced 👌
Thank you, I appreciate it. Glad you liked the video.
Really good video, great detail and thanks for not kicking out from under the car 😅. I just need to see if this applies the same way when the car has drum brakes?
We would be friends lol!! Great personality man. Thanks for the awesome video!!
Thank you bro.😊👍
Thanks man, helped me out.
598
Great video champ
Clean it before removing the dust cap. Great vid
Good video, nice! 👍🏻
Merci ça M a beaucoup aidé
Doit-on changer les deux roues arriere
Nice job
Hi good video. Nice and to the point. Quick question : Any grease to use ...? For example the part the new bearing slides onto?
pretty sure there needs to be friction there. the bearing has a sleeve that sits on the spindle. the sleeve is what he had to crack to get off
Very well done
Great job on vido. Only thing I do different is that I bush the caluaber before I take caluaber off.
Thanks!!!!
I swear this dude was on a dig in Egypt
Dust flying everywhere
32 mm for the wheel bearing?
Yes, just did it myself yesterday
Thank you
good job
thanks
Do you have to take off the inner race or why do I need to remove can someone help me doing this today and dident quiet understand that part
Are the new bearings sealed with grease then ?
Would a bad wheel bearing cause a tsc light on?
👌👌👌
Is there any other way to get the race off other than using the cutting tool?
I put a thin screwdriver behind it and worked it top, bottom, left, right and eventually got it far enough out I could slide it off.
@@shaynekraczek3999 thanks haha I left this comment just over 1 year ago 😂. The race popped right off and luckily wasn’t stuck for ke
Haha oh good. Glad you're not still driving around with a busted wheel bearing 😂
Dope
my local garage wants $500 each to change them, must be the flat rate price
The stake on mine is too tight to get any punch into it… what should I do?
Cant-cha change just the bearing & use d old hub like i did on d front?
Niiiice 🫡
Got a drill just like that one
Why was there no screws? Is that okay to not have screws in it?
The screws do nothing really for us. More for the factory when they are building the car. It lightly secures the rotor while it's travelling down the line.
Sup homie?!
Nice when you have all the tools😅
Socket size please
32mm
Funny how you just said "if you start with air the. Finish with air...." but then you sprayed brake cleaner
Your breathing in asbesdos dust stop blowing air on that brake area.
Too much talking.