Ball Joint Replacement - 2003 - 2007 Honda Accord (04 - 08 Acura TSX, TL)
Vložit
- čas přidán 3. 08. 2018
- This video will show you how to replace front suspension lower ball joint on a 2003 - 2007 Honda Accord. The replacement was performed on a 2004 4 dr Accord LX. Method of performing this service can also be done on a 04 - 08 Acura TSX & TL. The replacement will improve ride quality and help correct wheel alignment, tire wear and traction issues. Honda specific ball joint press adapters and a ball joint press (some auto parts retailers rent them) are needed to perform this replacement. For the highest quality ball joint with a lifetime warranty, go with MOOG brand suspension products.
04:30 After adding grease through this fitting, remove the grease fitting, and install a
grease fitting plug.
If you'd like to make a donation to the channel, please follow the link below: paypal.me/HardlyMoving?locale...
Parts and Specialty Tools:
Honda Accord 2003 thru 2012 & Honda Crosstour 2020 thru 2014 Haynes Repair Manual: Honda Accord 2003 thru 2012 & Honda Crosstour 2010 thru 2014
amzn.to/3mqrr79
Acura TL (99-08) Haynes Repair Manual (Automotive Repair Manual)
amzn.to/3yOjQED
Moog Honda Ball Joint:
amzn.to/36mAKtT
36 mm CV Axle Shaft Nut Socket:
amzn.to/2Y0QoZd
Honda Ball Joint Adapter Tool Up to Year 2000:
amzn.to/2Rvjz3A
Honda Ball Joint Adapter Tool From 2003 On Up:
amzn.to/2N70PZS
Milwaukee 2767-20 M18 Fuel High Torque 1/2-Inch Impact Wrench with Friction Ring (bare tool - no battery)
amzn.to/35kOBS9
Milwaukee 2755B-20 M18 FUEL 1/2" Compact Impact Wrench w/ Friction Ring (bare tool - no battery)
amzn.to/2OVStlj
OrionMotorTech Heavy Duty Ball Joint Press & U Joint Removal Tool Kit with 4wd Adapters, for Most 2WD and 4WD Cars and Light Trucks (BK)
amzn.to/2Hz7w30
OTC 3/8" Impact Driver
amzn.to/2UMacgX
8-Pack of Honda / Acura Brake Disc Rotor Screws by Mission Automotive - Stainless Steel
amzn.to/2U0lWip
Permatex 22058 Dielectric Tune-Up Grease:
amzn.to/2Y06stU
As an Amazon associate, I earn from qualifying purchases. Thank you for your support!
Please Subscribe: goo.gl/x6fySQ
#hondaballjoint #acuraballjoint
the best how to videos I've seen. thanks for not taking 3 minutes at the beginning of the video talking and explaining. right to the point! thanks again.
Thanks and glad you liked it!
Most videos spend the first 3 minutes asking for people to sub or thumbs up🙄 thanks
I know. Irritating isn't it?
No auto repair job ever goes smoothly, regardless of how small it may be. Stuck parts and the like. This vid really helped when my brother and I changed the uppers, lowers, sway links and balljoints on his Accord. Rented that press tool from a local parts store and buddy, that thing saved the day. Thanks for a good, clear, no-nonsense vid.
Thanks! Rusty parts can mess up a small job. Thanks for sharing your experience.
Nice to watch a mechanic with a brain in action, thankyou for this video,helped me alot
Helping people is the real pleasure in this life ..thanx a lot for your effort
Yes ... you are right ... helping people!
Great video for showing how it's done for guys who already know how to do it. For anyone who doesn't recognize all the bits and bobs involved from strange unfamiliar angles, a few words telling what's being done during the process would take no extra time and make the video a valuable one.
Thanks for your critique! You're right. Should have had some more audio in the video.
Best car repair video EVER. Jumps right in. Fast track from step to step, each step shown with a sped-up video snip of that step. No wasted time, no blah blah talking, no verbal descriptions in lieu of a video, the description gives the exact details of the car being worked on. Love it.
Glad you liked it and thanks for your support!
I had a hard time trying to pop out the ball joint and broke the replacement. You made it look so easy with the right tool. I broke down and ordered the adapter from Amazon. Nice video!!!
Always easier and less frustrating when using the right tool!
Thank you for this. Your notes on the OTC parts really helped me out on my 07 Accord V6. I was able to replace the front driver's side ball joint myself and saved a boat load of money!
Hey good for you! Always cheaper and sometimes better if you do it yourself!
Did you remove the rubber boot when installing? I seen other videos that they didn't at all they just pressed it in.
@@Alvaresmaico20 You do not need to remove the boot to install the new OEM ball joint, given that you use an OEM ball joint and this OTC installation kit.
I'm a Honda tech and you did that the hardest way possible , don't need to remove 95% of that stuff , and only need a big socket and a hammer to remove and install the joint
Thanks for sharing! Send me some raw video, I'll edit and publish it.
I rarely take time to comment, but you made that look like child's play. Excellent job. Post More.
Thanks Philip for your complement comment! If you really want to see an interesting video, check out my Lexus RX300 evaporator core replacement job ... it's a long winded 30 minute video :
czcams.com/video/t-xuqRKJxpo/video.html
Cheers.
One of those jobs where I kinda knew it'd all have to come off but hoped there was a quicker technique.
Thanks for taking the time.
You bet!
Best car video I've seen on CZcams ever, no BS straight to the point, good job.
When I fit the ring over the ball joint dust covers I use two pieces of brake pipe it's quick and easy
Good idea! I'll try it next time.
One of the best I seen ...GOOD MAN make more!!! Get some knee pads that SHHHT hurts
That's what we're doing ... making more...thx. I sometimes use a knee pad on my right knee since that's where I land on going down.
I love your video sir! No BS talking, straight to the point. Keep it up, by far one of the best vids ever.
Thanks!
This is a really good video man, sped up just right, and that spring installation was super smart too. I'm doing upper control arms and lower ball joints so its really helpful
Thanks!
By far the best help video i have ever watched!! Right to the point. And i didnt have to watch someone remove all 5 lugs with a ratchet. A+++
Thanks!
This is the best video of this kind that i have ever seen. Really a good piece of work.
Thanks todd3205!
Thanks and appreciate your comment!
Great video. Straight to the point. No BS long introduction.
Thanks!
@Hardly Moving Productions You are the man! Thanks for sharing the great tips and insights so others may learn how to do these jobs ourselves.
I appreciate that!
If you have a complete tool the job is getting much more easier.👍
Yes ... you are correct using the right tools.
🔥 Awesome,So smooth this repair went, if only our repairs up here where we get tons of ❄️ 🧂 things would go so easy hahaha great diy!
Thanks 👍
Thank you so much brother. I just had a scary mishap last night while going about 75 mph oh the highway 11pm. Ball joint snapped and took down the axle with it. Gonna try and attempt this on my own! Cant afford to go to the shop. Worst timing but trying to take it as it comes.
That's what happens when the ball joint breaks.
@@hardlymovingpro Lesson learned the hard way. I should've done a more thorough inspection on the car when I bought it 3 months ago. Just went outside not too long ago and found multiple things wrong on both sides, so I'm just doing an entire new suspension for both sides and play it safe
Good decision. You're better off in the long run replacing everything vs revisiting new problems.
Great video I wish I would of replace mine lower ball joint on my 03 Accord 5speed befor it broke and broke my axle too fixing everything now just got stuck on that trim ring but you showed me how to remove it thanks 🤟🏾
Glad it worked out for you!
Great job man, thanks a lot for the video 👍👍
Thanks for the thumbs up Rodrigo!
I enjoyed the visit...... you have a talent great job, Thanks
Thanks for your comment and support!
Gotta do two of these tomorrow on an 06 accord. Good video!
Thanks...and good luck!
Any advice? I have an 06 and I need to get mind replaced.
Get ball joints from Moog
nasze wspaniałe autka , i bezpieczna jazda dla siebie i innych
Good video man, definitely did it the quick way & it’s still properly installed!
Thanks! Quick and easy!
Thanks for the detailed vid boss,,,,,much respect
Thanks for your comment and support!
Very much
Great videos very informative except for you have it listed that I need a 32 mm socket to remove the axle nut my car a 2005 Honda Accord EX required a 1inch and a 1/4inch socket to remove the axle nut great video
*UPDATE* I could never get my axle nut to break loose I broke 2 torque wrenches 1 of them I ended bending in half and I went through 2 sets of impact connectors I tried heat an everything still could never get the nut off just to update.
Did you Bend out the detent on the axle nut? What I use is a thick breaker bar. It works good even up here in Canada where things are rusty.
Chris Medlin , don’t use torque wrenches to remove anything. You need a breaker bar 1/2 “ or larger. I purchased a 1” socket wrench with a 32mm socket . It loosens it so effortlessly. Don’t forget to bang back out the indented nut before trying to break it loose.
Inch and a quarter is pretty close to 32 millimeter.
Great video. Very helpful.
Very very helpful, brilliant tutorial.
Thanks for your comment ... appreciate it!
Like an art-house short film. Amazing
Thanks for your comment and glad you liked it!
I love watching your videos. Thanks for sharing
Thanks for your comment and support!
awesome. super helpful for doing similar on a 2003 civic soon.
Thanks!
That was fast!!! Nice work. Hope I get it done somewhat the same with just hand tools haha
Good luck!
Great vid thanks 🙏 for sharing 👍
Glad you liked it and thanks for your comment!
Interesantes video Gracias 😊
Good job bro,,,hi from Spain,,,
good job
Gracias por el video ahora ya se como cambiar el ball joint 👍
Me alegro de que te haya gustado el video y gracias por tu apoyo!
@@hardlymovingpro órale hablas español ,, que chido empezare a mirar tus videos saludos donde quiera que te encuentres otra cosa me suscribi a tu pagina..
Como son los bujes de amortiguadores delanteros
Felicitări pentru aceasta prezentare succes.
Mulțumiri!
You are very very skillful.
Thanks!
Nice sir really gr8 working
Thanks for your comment and support!
Any alternative on how to get the ball joint without buying that honda adapter set for the press bec i rented it out from oreillys and the honda adapter set didnt have the right size that goes underneath the ball joint ? And it says on amazon that they are currently unavailable so im stuck rn
Get an adapter with the right size diameter. Use a rotary metal cut off tool and make cut outs to make it fit. You can secure the adapter in a vice so it will be stable when you're making the cuts.
Fast and efficient video! I loved it
Glad you liked it!
Very informative, learned a cool tricks
Good for you!
I did this 2x on my 05 Accord. Both times it came loose in the knuckle. I asked my friend who is the shop forman 30 years at local Honda dealer. He advised they have a tendency to "woler" out the mounting whole and come lose in the whole. They replace the knuckle with the joint factory mounted. I've done this several times successfully. The price is less than a hundred on most online stores.
Very strange. Never had a customer comeback on a Honda ball joint replacement
The part with the ball joint installed used to be prohibitively expensive. Now it's easier, cheaper, and in my experience more reliable. My car had more than 200k when I attempted the replacement.
Thank you sir
good video, straight to the point and none of that talking b.s...👍🏼
Thanks ... appreciate your comment!
Hi, i like this video that show step clearly. I would like to know the size of the cotter pin of the ball join, did you know that and could you tell me? I think i should prepare some before i do this replacement.
New ball joints come with new cotter pins.
Can you please tell me what kit I will need for a 2006 acura tsx? You have a few links posted, dont know which one to pick. Thanks
I believe the TSX uses slightly different parts. The worked performed on this car was an Accord. Whatever parts you may want to order via Amazon, you can perform a part compatibility match based on the Year / Make / Model.
These are the types of videos I like , straight to the point.
What model impact gun is that ?
It's a Milwaukee M18 1/2" impact driver ... around 400 lbs of torque ... bought around 8 years ago. Newer version are brushless with more torque.
Hardly Moving Productions
Thanks for the fast response !
Any chance you used the same
Impact for the axle nut or was that a compressor gun ?
Used the same electric impact gun to torque down the axle nut.
Awesome!
Good work 👍
Thanks!
Just an idea to keep in mind, if you plan on reusing any balljoints or tie rod ends, leave the nut on after loosing it. This way if you do happen to hit it with a hammer you won't mess the threads up. I did that one time, had to taper file the end of the threads to get the nut back on, leaving that nut on can save you time, money and hassle.
Good advance thinking! People should keep in mind that whatever was a hassle to take off might be a hassle to put back on.
@@hardlymovingpro actually with Hondas that's spot on, especially those wheel bearings... I hate those things. They are not easy to do, heck my 97 f150 4x4 was easier, 3 bolts and the entire hub assemblies are removed... takes two hours tops for both sides if you take your time. Honda front ends can be tough depending what needs replaced.
@@garyr7027 You're right. Bolt on wheel hub and bearing assemblies are a easy. However, some people forget to dislodge the cv shaft from the hub splines and struggle to get the assembly off. Here's a video I published a month ago on how to replace those pressed in bearings: czcams.com/video/EapRYC-fS8g/video.html
@@hardlymovingpro that's true, those splines can get stuck. I got lucky with my truck, they slid right off. Got the link, I'll watch cause I never know when I'll need it... thanks.
@@garyr7027 burro
Great video sir
Thanks for your post and watch our other Honda DIY's to learn more!
So I’m not sure how you got out the big thing behind the hub but I’ve tried everything and I can’t get it out yours just seem to fall out mine feels like it’s welded in
Are you referring to the cv axle? If so, watch this video: czcams.com/video/c6hktAUFyrc/video.html
how did that abs sensor come out like butter. usually thats stuck and need to drill out
Depends on where the car lived. If in where they salt roads in the Winter, the sensor hole will get rusty. Try soaking with penetrating oil overnight before attempting removal. Or just leave the sensor in there with the wire detached.
Great How to video. No 5 mins of BS. Straight to the point
Thanks! Glad you liked it!
The ball joint removal socket, did you custom cut that?? Nothing I see around has anything like that
No but used a older version ball joint adapter that semi worked. Believe there are adapters for new models but they're not cheap. Better off making your own adapter with custom cuts.
What does the large steel ring on the back of the hub do? (Other than get in the way!)
Dust shield
I looked up some ball joints for a 2008 Acura TL and they are greased already with no option to further grease. I don’t need to remove boot on those right?
That’s an excellent question. Only if the boot diameter is not larger than the diameter of the mounting hole in the steering knuckle. I now only buy lower ball joints where the boot is flush with the ball joint. Checkout Moog brand ball joints.
Look like you had to modify the receiver portion of the ball joint press tool to have clearance for it to work on this job. Is that correct?
Nope. Although not a perfect fit but good enough to get most of it out.
That did NOT look easy. Glad you did it.
Awesome video. Never thought about greasing the ball joint. First ones I purchased years ago from Moog were sealed at the top. More recently they're open for zirc fitting. I can see grease in the hole but it wouldn't hurt to add more.
Thanks for your comment. The higher quality ball joints, IMHO, like Moog don't have grease fittings.
Thanks for this, I saw you didn't use the ring "removal" adapter for the press, did you just hang that top ring on the upper part of the press just right? did you cut out the adaptor?I have problems because none of the adaptors fit right in my knuckle...I am going to take a page out of your book it looks like you just lined it up the best you could against the knuckle. Thanks.
Yes. I hanged that top top ring. Did not cut out the adapter. Yes .. lined up as best I could against the knuckle.
Always appreciated
You bet!
What size sockets did you put on the on the ball joint?
The ball joint nuts?
Great job buddy. 👍 👍
Thanks for the visit!
Ball joint I was sold has a unremoveable boot w/o grease fitting.Maybe I'm getting old but all front end parts used to be equipped with a grease fitting(so you could grease them).If Turkey gets attacked from the rear,will Greece help ?
If the dust shield boot is flush with the body of the ball joint, you'll be able to press it in without ripping the boot.
Thanks for your knowledge,more info than any other.@@hardlymovingpro
You bet!
Nice and fast Milwaukee impact 💣👍
They're real time savers!
That was a good video. Take it from me. The best mechanic in California
Thanks!
What size fittings are you using on ball joint press thanks
Fittings with cut outs specifically designed to press out and in Honda ball joints
Thanks for the video. I tried doing this but even the 'honda' specific adapter kit did not fit the ball joint. The receiver cup was a little too small and wouldn't let the ball joint come out. What brand adapter kit did you use? I have a 2004 acura tsx. Thanks
It looks like beginning in 2003, Honda and Acura went to a larger diameter ball joint. If you carefully watch the video, I used the earlier version of the Honda ball joint removal tool to get around half of the ball joint out. I then hammered the remainder out. I also have had difficulty finding a Honda tool set for the larger diameter ball joint.
The adjustable puller tool that looks like the pitman arm puller tool works for removing the ball joint. I need to replace one lower ball joint and I'm dreading it. 😭
I bought the cheapest ball joint tool set I could find on Amazon but it didn't have the parts necessary to remove the old ball joint.
What set will work with a 2008 TSX ?
This press kit, although made for earlier models, can work to get most of the ball joint out: amzn.to/3oBXbqU
its impossible to find correct adapter sizes for Accord 2005 here in Calgary
You could use a generic adapter that matches the outer diameter of the ball joint and make it fit by cutting a notch with a rotary cut off tool.
Broooo
Coba upload cara melepaskan rac powerstering honda accord prestage 89....
Why remove the boot prior to install? Curious. Thanks for the vid
If the replacement ball joint's boot is not flush with the ball joint body, the boot won't squeeze through the steering knuckle ball joint hole. Better off get a ball joint with a flush boot.
Bhai kaise pata kare ki ball joint kharab hone wala h kya kuchh aawaj aata h kya🤔
Did you put anything in the whole you took the grease fitting out of or do you just leave it open?
After injecting the grease, screw off the grease fitting nipple and screw on a plug. The new ball joint should have the plug in the replacement box. Sorry ... didn't show that in the video. Don't leave the nipple on. It won't clear the CV axle.
Great video.
Glad you enjoyed it!
Great video easy to follow along. Did u use the Honda adapter tool in the description?
Thanks. Yes ... Used the adapter
Hi. . . at 4:20 I realise the flat surface of the ball joint isn't flush with the housing surrounding it. Why is this so? Should it not be flush? I am asking because my mechanic installed mine flush...
It all depends on the parts manufacturer. I now buy only flush dust booted ball joints.
When replacing front lower ball joints on an 08 Accord, should you replace the lower or upper control arms as well?
Usually worthwhile doing.
I replaced a few ball joints on my Honda Accords I have two of them and 03 and an 06 and none of the times did I have to take the rubber boot off. It might depend on the brand of the part. Honda brand and Moog brand is.what I used.
Yes ... you are correct. On the OEM and some aftermarket ball joints the boot is flush with the ball joint. This one I bought was not flush. I now only buy ball joints with flush boots.
what model milwaukee gun are you using?
I've got around 6 different Milwaukee models. A M18 1/2" that generates 1400 lbs of twist off torque. A lighter medium torque for 14 mm to 17 mm nuts and bolts. A 3/8" M12 series for 12 to 8 mm nuts and bolts. A 3/8" and 1/2" M12 series ratchet wrench for tight spaces.
Good work, and make IT alene..😄
Thanks!
I didn't notice you replaced the upper and lower control arms the first time 😅
Did a separate video on that.
What do you think about using mechanics wire and braid the two ends to replace that spring...?
Don't understand ... what spring?
@@hardlymovingproat the bottom of the boot.
@@Usmanthemecano Oh ... you're talking about the ball joint dust boot's retention ring. Don't think the braid idea will hold. If you can get the contact surfaces completely free of grease, you can glue it with JB Weld.
Does that ball have a snap ring or anything holding it into place.
Nope. The only ring, which I think is overkill, is the ring installed after the new ball joint is pressed onto the steering knuckle.
can u pls put a list of the tool i need do to this job?
Tools and parts used are listed in this video's description.
Did you do a vid of the upper install too ?
Yes. It's covered in my Honda front strut and control arm video. Its easier to replace the upper control arm that comes with new bushings and a ball joint.
What happens if u just press it in with the boot?
Not enough room. The boot was tear.
Should the OTC 6734 work on a 2007 acura tl?
Honda Accord Sedan ’03-’08, Honda Accord Coupe’03-’08 and Acura TSX ’04-’08. The TL is basically an Accord so it should work.
Good video!! One question you didnt need to put the snap ring retainer on the ball joint??
Some kits come with new rings and some do not. Quite frankly, I don't really see a need for it. Just how in the heck is the ball joint going to possibly come out being press fitted into the steering knuckle and bolted to the lower control arm? Maybe ... perhaps ... if you run your car into a ginormous pot hole? If that happened, you've got more to fix than a ball joint.
Oh ok, thanks!!
No problem!
No problem!
Very good video
Thanks!
ok .can i buy the 3 to 7 honda accord to install it in a 2006 acura tsx ? .i cant find the complete assembly for the tsx , just for honda .
The 03 to 07 Accord lower ball joint fits the 04 to 08 TSX. Both vehicles use the same suspension and engine ... from my understanding.
@@hardlymovingpro ok thanks man .my concern is that on internet they sell these honda spindle knuckle for honda accord 03 to 07 but it say dosent fit acura tsx .and i see on other pages that honda accord 03 to 07 fix the acura 2006 😶 i dont know why they do that ,on ebay is full of these but are used and i dont trust an used part .and it say clear and loud ,fit honda and acura ..ok thanks for your help boss .
04-08 TSX is pretty much the same car as a 03-07 4 cyl Accord.
Great job
nice video
Thanks for your comment and support!
damn dude. i'm so glad i own a toyota. its like a 10 minute job. appreciate the video though bro
I'd say lower ball joints are the weakest part of older Honda's. Around 2004 the ball joints got beefier. When there aren't any worn suspension components, Honda suspensions gives a better ride than a Toyota. But to save money, I've see Honda moving away from double wishbone.
@@hardlymovingpro i've owned hondas before i've owned toyotas and i like the camry ride better than accord. that's just my experience. i never took the honda apart to the extent that i did with my toyotas though.
Honda's double wishbone (control arm) suspensions keeps all the tire threads on the road when taking high speed turns over rough surfaces. More costly to produce for the auto makers. Pretty much standard for European as well as some Asian luxury cars. The newer Lexus LS sedans have up to 4 control arms. McPherson struts with rotating upper strut mounts is cheaper to design and make for Toyota.
@@hardlymovingpro Yes there is a good reason for the extra complication and cost of double wishbones
That's why the kids love to trick up the older Civics