Honda Clone (GX390) Engine Rebuild - Low Hour Engine Dropped a Valve
Vložit
- čas přidán 7. 09. 2024
- Last week I pulled this engine off a Generac GP6500 after this engine dropped a valve and punched a hole in the piston. The cylinder and block survived and this is a good candidate for a rebuild. The problem is the price of parts. The parts cost is close to $500 from Generac to repair. I have parts from other blown-up 389cc Honda clone engines. I think I have enough to piece this one together for about $13. The problem is this engine has a Hemi head and the heads I have are standard. Can I change a Honda clone hemi into a standard head Honda clone? Lets hope so.
Generator Model: G0076700
Previous Video: • Generac Generator Drop...
Generac Parts Needed for Rebuild:
Cylinder Head (0K56930SRV)
Valves (0J39430126)
Piston (0J39430122)
Ring Set (0J39430121)
Piston Retainer Clip (0G84420237)
Wrist Pin (0G84420238)
Connecting Rod (0G84420235)
Head Gasket (0J39340116)
Crankcase Gasket (0G84420115)
I no longer use Harbor Freight Super Heavy Duty Degreaser in my ultrasonic cleaner. Harbor Freight changed the recipe. The bottle previously stated "NON-CORROSIVE". Now it says "CORROSIVE", "do not user on Aluminum". It now damages most carburetors. Recently I have been using Simple Green PRO HD with good results.
Visit My Amazon Store:
www.amazon.com...
3M Roloc Bristle Disc: amzn.to/3UxsR1j
Assembly Lube (Permatex 81950): amzn.to/3QhHkvL
Blind Hole Bearing Slide Hammer: amzn.to/4d7yvyn
Caliper: amzn.to/4d9no84
Compression Tester (MityVac MV5530): amzn.to/3wclvXq
Cylinder Hone: amzn.to/3w4LXlQ
Dremel Stainless Steel Brush: amzn.to/4b9ti7c
Feeler Gauge (Lisle 68100): amzn.to/4aY3gnm
Gasket Kit: amzn.to/449RmVt
Lapping Suction Cups: amzn.to/3Jy2W38
Piston Ring Set: www.ebay.com/i...
Tachometer (Rotary 15344 / Echo PET-1000R): amzn.to/3Jy0ols
Test Tank: amzn.to/3xPuuhM
Thread Locker (Permatex 24010): amzn.to/4dcq30y
Valve Lapping Compound (Permatex 80037): amzn.to/4dcpbci
If you want to donate to the channel, you can use the CZcams "Super Thanks" feature or via PayPal: www.paypal.com...
#Generac #Hemi #HeadSwap #GeneratorRepair #Generator #SmallEngineRepair #SmallEngine #DIY #Fixed #Troubleshooting #HowTo
389cc, 390cc, 420cc, Alternator, Compression Test, Dropped Valve, End Gap, Engine Rebuild, Feeler Gauge, Fixed, GX390, Generac, Generator, Governor Reset, Head Gasket, Head Swap, Hemi Head, Hertz, Honda Clone, Hone Cylinder, How To, How-To, Lap Valves, Load Test, New Rings, Piston, Push Rods, Rebuild, Repair, Small Engine, Timing Mark, Timing, Troubleshooting, Valve Clearance
I had a Dodge 318 V8 that overheated and burned a piston. Money was tight at the time, so I went to a "pull your own" junkyard, got a rod & piston, used the original bearings and rings from my engine, put it all together with new gaskets, got another 30,000 miles out of it. Desperation and ingenuity sometimes work well as a team.
I had a 318 also, which stripped out the plastic timing gear and bent all of the valves. The "mechanic" that replaced it put it in one tooth off, and messed up the math on his bill. I took it from there, putting on another set of heads that my brother came up with that had one bent valve thanks to his friend's engine throwing a rod, so I fixed that, cleaned the thing up, and that engine is now in my truck, still running good.
Hands of a surgeon with a calm and cool demeanor.
WTF are you talking about?
@@Look_What_You_Did Quit smokin crack!
Fresh cup of tea, let’s settle in for a little JC Thursday! Oh wait, I should be working!
Bwahaha
I wonder if the GNP drops on a day that Jim drops a video. 😁
It never hurts to get some education while at work!
It's why I have two monitors...hehe
@@lot27a Only 2?
Hi James I’m not sure if you will see this post but I recently discovered your CZcams channel and as I was on vacation this week (and dealing with a nasty cold) I binged on your videos and was inspired to take another crack at fixing my deceased father in laws old 1988 John Deere SX75 riding mower (sentimental to my wife). Following your diagnostic thinking( spark, fuel, timing etc.) I got it running again and will give it another life mowing the lawn at our camp.
Please keep producing (only if you’re enjoying doing so) these videos as your thought process and attention to detail is inspiring…
Michael O.
That’s great to hear.
Great video. Probably one of my favorites just because you took parts you had to fix it. Almost everyone who came across a motor with that kind of damage would have scrapped it . Saving a new motor for $34, priceless. No doubt it will pull its weight and drive a generator. Breathing life into one that was also headed for the scrap yard. When I was real young my uncle went to school for small engine repair. While he was there my grandfather went to a auction at a local business that had just gone out of business. He got a truck load of new and new/old stock still in original packages. (Briggs and tecumseh parts). There was also boxes of old parts from motors taken apart and saved for the same purpose you just showed. I was bored one rainy day and dug thru the many boxes of old parts and actually found enough to assemble a complete motor. It was about a 4 horse maybe or smaller. Flat head briggs. I actually assembled it with no gaskets. It ran like a new motor. I was about 11 years old. Didn't know gaskets was needed. Lol. My uncle came home on weekends. I showed him what I did. We dug thru the parts and found gaskets. That motor ran great. I actually put it on a mini bike frame we got from another suction. It ran great for a long time til my younger brother blew it up pulling on the governor arm to make it go faster. Lol. This video reminded me of that. I don't know how I got it to work. I basically knew nothing about small engines. No skill used. Pure luck.
I was a young lad mucking about with engines, my dad bought home a Briggs rotary hoe that he got from his brother. The thing didn't run so I took a look at it not knowing much about engines back then. I spent an afternoon tinkering with it, pulling it over checking for spark etc. After a bunch of pulling on it, it fired up and run. My dad come over and said to me didn't think it would run again, he used it to dig his garden for many years after that.
This was the worst damage I've seen in your videos.
If you didn't have the spare parts, that machine would've been for parts only.
Now it lives to fight another day. Good job.
Best to insert a snug fitting drill bit inside the dowels so when you grip the dowel it does not deform👍
One thing I have found is it's very important to thoroughly remove all the microscopic residue remaining in the bores after final honing. 409 seems to work very well at floating the nasty bits out using a lint free cloth to apply the cleaner. After using a little elbow grease you will have the cleanest surface in town.lol
Bugs me that you did such a great job fixing and cleaning the motor, only to put that rusty flywheel on without so much as wiping off the rust.... 😄
Once again, thanx for a great and informative video.
Nice,no internal plastic parts. I like watching CZcams videos where people are repairing internal combustion engines. I’ve a Generac 6,500 continuous watts,industrial commercial generator. I purchased it in 1995. It has performed perfectly. The only thing I don’t like about this generator. The exhaust muffler is quite small and extremely loud. My Generac brushless continuous 6,500 watt 7,800 watt short term usage generator has a 13 horsepower Honda Clone internal combustion engine. I instantly converted the generator over to propane. Never having to worry about the gasoline going bad. I purchased a a 500 gallon propane tank. I installed it myself. I also built a shed and a permanent spot for the generator. I ran 0 stranded copper wire from an electric panel in my shed to my main panel in my home’s garage. My brother in law was an electrician and gave me the wire,sub panel and breakers. I didn’t use a disconnect switch. My wife and children knew to turn off the main breaker and turn on the 30 amp breaker for the generator. I also put an electric starter on the generator. The Honda Clone already had a flywheel with the gear teeth on it. Many manufacturers of generators that has the option to put an electric starter on it. Don’t have the gear teeth on the flywheel. The Honda Clone has an oil pump and filter. When I was living in the mountains of Pennsylvania. My neighborhood power grid was not on a loop. During our regular winter snowstorms . We would many times lose power for up to 5 days. The Generac Generator did its job exceptionally well. It would run our Well Pump and oil fired home heater. That had a copper coil inside for hot water. I also had a ventless fireplace heater. I purchased another 500 gallon propane tank for that. I would use a battery from my Ford F-350 with a DC to AC converter for the televisions and computers. The Generac Generator also has a 12 volt DC port for charging vehicle batteries and charge the Truck Battery daily. My truck has 2 batteries and I would swap them out daily. Anyway I really like your videos. Over time I will most likely watch all of your videos. The only thing that sucked was I had an electric stove. We would use a Coleman camp stove and a propane grill for cooking. Many of my neighbors didn’t have generators and the ones that did. Didn’t drain the gasoline out and their generators would not run. Or they would have a bunch of cheap extension cords. Many would burn up. Our homes in my neighborhood were at least 100 yards apart. I would allow my one neighbor to plug in a high end 30 amp extension cord. So his baseboard heat wouldn’t freeze. He had the same problem. Gasoline over a year old, no stabilizer in the gasoline. (The carburetor from my Generac was identical to my neighbors generator carburetor. After it dawned on me that I had a brand new carburetor. I installed it on his generator. ) His generator of course would not start. He and his wife had 4 small children. He would help me without question any time I asked. I would always return the favor. I ended up converting his generator over to propane and installed a disconnect switch,sub panel and breakers in his shed. This is what you do for neighbors that are decent hardworking people. After 20 years of moving. We still keep in communication regularly. He was so thankful when I converted his generator over to propane. My brother in law gave me all the 0 stranded copper wire. Sub Panel,disconnect switch and breakers. Another neighbor on the other side was a complete a-hole. He also had baseboard heat. Didn’t drain the gasoline out of his generator. One snow storm we had lost power for 5 days. All his pipes froze and split. The neighbor I was glad to help. I had him purchase antifreeze and filled his baseboard heating system with it. Just in case,He never had to worry about his pipes freezing and splitting. I had him purchase. Ford diesel antifreeze that never goes bad. His baseboard heating system still has the same antifreeze in it. No corrosion at all.
Nice work Jim! Good to see that the Hemi can be swapped-out for a standard head with minimal changes.
Brilliant your ability to know what parts fit other engines is priceless. Congrats 😊😊😊
Hi I'm a D I Y person and right now I am building a gx 390 clone based on your teachings, I learned alot about generators and small engines. Great video keep up the good work
Hi James, in the past I've used an old drill chuck to grab round pins for removal, it works very well.
Rich
Thanks, will remember that trick.
I’ve even hydraulic’d them out with bread and a punch. Whatever works!
@@KensSmallEngineRepair yes I learned that trick years ago for removing a piolet bearing from a car flywheel!!
@@richb419 I even used a Twinkee once on the pilot Bushing on my 55 Chevy!
@@KensSmallEngineRepair That works with bushings and bearings, but a thin wall alignment sleeve doesn't have enough surface in the removal direction to generate much force.
I would have tried a brief application of heat. It might have had retaining compound or sealant, and the aluminum casing will expand more than the steel sleeve.
Thrifty and clever James, well done it sounds great!
THANK YOU for the extra info about the HF cleaner... GREAT JOB on the engine! and the video editing!
Great precise and accurate rebuild. That's a good motor.
The first though that occurred to me about that holed piston is; "can it be repaired?" Perhaps a few words on why you wouldn't clean up the hole, bevel it then pour some molten aluminium from below?
I don't know why, but your videos engross me. So much so that I have kept an old OHV motor mower engine that I dream of rebuilding (although I have no use for it).
The thin head gasket is used on all the newer honda motors now days and some clones It. It gives a higher compression ratio as it lowers the distance between the piston and head. This will work out good as it will give a bit more hp back after swapping from the hemi head.
I really appreciate that you approach each of your videos from a novice’s perspective even though you are an expert at your craft. Your camera positioning and editing are best in class. Thanks for all the effort!
Thanks
To get to dows out easily you put a drill bit in the middle that fits nicely and some vice grips on the out outside of the dow and should come out with a twist and a pull!!😁
Nice work!! I took a GN-190 and made a GN-220 head fit because I couldn’t get valves for an early GN-190. It worked out great. Thanks!
great job saving this engine. love to see that. you could have saved the alignment pins by the judicious application of a little heat. a propane torch to about 300 degrees and it would have come right out. Aluminum expands at 3 times the rate of steel. I used this to get out the drain plug on my F-250 Differential.
Thanks. It caught me off guard. Never had a problem until today removing pins.
Great job James........and the engine lives again....BRAVO.
Thanks
Exceeds Expectations? For that bit of magic, you get an Outstanding!
Nice job with the dowel pin extraction!👍👍👍
Love your videos! Next time you run into stuck locators find a drill bit that fits tight into the pin and use a good pair of vise grips.
Exellent work. Very quiet & very smooth.
Great job Jim, really enjoyed the video!
Catching up on this video, Jim. On those dowel pins, I recently learned a little trick. Put the proper size drill bit shank into the dowel so it is supported, and then you can grab them as tight as you like with vice grips without crushing them. Then with a little twist even really stuck ones will come right out.
Thanks for saying you can adjust the valves in many different positions of the engine. I do that and constantly get comments that I'm wrong, it has to be at TDC, etc. Nice work on the rebuild! 👍🏻
Great idea, thanks Jon. That one caught me off guard. Never had so much trouble with dowel pins. The engine was left outside for a while with the head off and the pins rust jacked in place.
I hear the same about valves. So many people adjust their valves on TDC of the wrong stroke not realizing the piston is at the top twice. This way it’s a no brainer and it has never caused an issue.
Nice job. I think that engine started on the first compression stroke.
Great save James, for those of us that still DYI our equipment, looking for used parts is getting tougher as many small engine shop don't keep or want to sell used part.
Our options are those who have a resale on a social media site or local swap meets.
Used parts are just as good as new as you have shown.
Keep posting as each time your posts show something new that DYIers use.
Tks. Michael
Great problem solving on those stubborn pins. In my comfy chair thinking - since I have no slide hammer - I'd have tried cutting a shallow slot in the pin with a hack saw - or maybe two opposing - and then levering on it/them with a screwdriver. But your solution was a lot more elegant 🙂.
Good job. It helps to have spare parts laying around. My wife calls it clutter.
James, you do such nice videos, very informative and educational, you are the master of Genny's...
Saving old iron, one project at a time! Nice! A lot of detective work involved, but a success in the end, potentially! 😊
Nice job! Informative, to the point, no annoying music, and never lost interest. I now have confidence to dig deeper into small engine repairs because of your video. Thanks!
a most excellent job as always! Thank you for going over all the differences between the hemi and non-hemi engines as this could be very helpful when one of us has a similar situation with other parts onhand. A TIP: when removing the locator dowels, just use a chisel to collapse/split them and they'll come right out.
James, I really appreciate you! For several things, including: (most importantly) failure analysis and theory of operation - actually explaining what the valve stem rotator cups do. I have no idea how many dozens of engine rebuilds/valve jobs, etc. I've seen on YT and you're the first to explain that! I have determined in the past 3 years of my small engine learning that I'm probably more of a diagnostician than anything else and having access to failure analysis and theory of operation information is what I look for more than anything else.
I learned a lot this time around, so thanks for that! Also, thanks for following up the previous video with this one - having these in immediate sequence in your upload schedule really helps with continuity, at least from my perspective. Since we already had the previous video clear in our memories, seeing this followup really helped to solidify what we'd absorbed from the previous one. I appreciate that you took the time to do this one immediately instead of moving on to who knows how many others you have waiting in the wings. :)
We all assume you torqued those exhaust bolts down. LOL! ;-)
Thanks. Lol, no room for a torque wrench on those bolts. Just made them good and tight.
When you lap the valves and lift it, rotate it a quarter turn before you put it down and continue.
Why? Just curious.
Yep, I'd swap parts like you did in a heartbeat. The piston/head are very different, of course. There may be a minor change in horsepower/volume/rotating mass, but who cares? Long as it runs. Cool job.
Great job James!
Very easy to understand your english, appreciate it. I am from Sweden
Totally agree. I am from Mexico and it seems he speaks in spanish! 👍🇲🇽
Well James, I’m impressed we do the hemi non-hemi head swap on predator 212s using a thin shim head gasket and the hemi piston which is a non-dish piston. It’s a flat top. It works very well but I can’t wait to see what happens when you put it on a machine to put it to work, I’ll keep an eye out for that video
Great work James !! You know your stuff! When I used to work on lawnmowers, I did the same thing you did.
It's always a good feeling when you successfully cobble parts from several units together into one good unit!
About the dowel pins in the cylinder: Stick a well fitting drill bit into, an you can grab them with the pliers without them colapsing. Better: With the the 3-jaw chuck of your lathe or drill press..
What an interesting video. Excellent news being able to convert from Hemi to parallel valve. Wonder if power output will be affected? Can't wait to see this engine coupled with a 7500 watt power head and see how it does under load. As always, thank you James for your awesome videos.
I just realized something you are saving $400 that's a win-win my friend
Hey James really enjoying your videos .
Thanks for all the extra work you're doing to make them .
One thing my Blacksmithing Great Grandfather taught my Dad is . When you need to strike the end of a bolt or shaft like you sometimes do to extract a rotor . Place a ballpeen hammer's ball end on the bolt head then strike the hammer with your heavier hammer . I don't know why but it works much better and lessens the chances on damage to the shaft .
Thanks again
I'm impressed with the engine rebuild. Using mismatched parts can be problematic. Glad this project worked as planned. I would want to run the loaded generator for at least 48 to 72 hours and then change the oil. Look for any metal. Then it can be sold knowing it's going to be ok.
It's nice to know that even a semi-professional can have trouble with bits which just "won't go" when you try to remove them.
The latest news in my engine fix-up saga is that I attempted to remove the main jet from the old carb but it simply refused to budge no matter what I tried. I've decided to try to find out what size it is and then, if it's larger than the jet on the new carb, I'll drill out the new jet. But I only have drill sizes 0.5mm and 1.0mm so I have to wait for delivery of a selection of drills I've ordered which are in 0.1mm increments between 0.5 and 1.0mm.
I managed to drill through the gunk in the old jet with the 0.5mm bit, but the new jet is larger than that yet smaller than the 1.0mm bit. So far as I can tell, the 1.0mm bit isn't attempting to drill through the gunk in the old jet but is being stopped by the metal, so I know that jet is smaller than 1.0mm as well. Now I just have to wait for the new bits and I can attempt to drill out the gunk in the old jet until I get a bit large enough that it hits metal, then go back to the next smaller bit and drill out the new jet to that size.
I have no backup plan at this stage if I discover that the old and new jets are actually the same size already.
I made the mistake of not putting oil in a generator a couple years ago after i rebuilt the engine. Needles to say glad it had a low oil sensor in it
Great start to the day
Superbly Executed James , was a pleasure to watch & take notes.
I'd like see it back on a power head run power again. Killer job as usual.
1:20:00, something you can do if you’re worried about losing the governor shaft down in the engine, put a pair of vise grips on the top of it.
How Hemi swap is a common upgrade for these engines, when trying to get more power out of them.
The tools you have bought are making things much easier for you. That ring installer is so worth it, as is the piston installer. Plus it just cuts down on the time monkeying with that stuff.
Excellent repair, really enjoyed the journey! That’s why I always keep extra good used parts and engines on hand, they can turn a totaled piece of equipment into a small bump in the road. Very satisfying to save something like that!
Propane torch to heat around those dowel pins...fall right out. Good video.
Great video Jim! You are truly the Dr. Frankenstein of small engines and generators 🙂 It is ALIVE!
When changing from a stock head on an car engine to a high performance head, it's important to check things like the push rod length. You did a great job. I had faith it would run just fine. 😊
Thanks
Brilliant James. Great video and very informative. I guess two heads are better than one😂 or even three👍😆
I watched this hr and and a half long video not learning a thing about motors but found a channel that cares about detail and I can get down with that. This was a very good video. Small engines dont have to be hard there was some foolery but everything was laid out for you. Polite and to the point. Your doing a great job 👏
This was really one of your top videos, in my opinion. I was a bit worried that the cam might be different with a hemi-head engine, but the way it runs that seems not to be an issue. Having a stash is certainly an advantage in this kind of work. Thanks for this very valuable video.
"It's a Hemi" the other style are Wedge heads what might be different is the design of the piston & possible valve reliefs bit I'm only four minutes in, let's see. Well as curly would say "Oil's well that ends Well." Odd though, usually Hemi heads have domes pistons for flame travel but not in small engines. Nice video as always.
sounded so smooth, great job
A HEMI is always a HEMI. Been driving Mopar HEMI cars the past 26 years 💪
MOPAR or NO CAR!
HISTORICAL NOTE A long time ago....Dr. John Hufnagle was one of the pioneers of artificial valve heart surgery at Georgetown University. I spent some time on his cardiovascular service and "assisted" in some of his surgeries. Cutting edge stuff at the time. Anyway, this repair/reconstruction reminded me of those heady days. Imagine being able to take out an infection ravaged mitral heart valve and replace it with a "new" mechanical device. Heady stuff. Watching James assess the piston damage and then calmly and cooly insert a "new" device reminded of yesteryear. Each step carefully assessed, followed by a precise mechanical effort.
The first mechanical valves all had very audible CLICKS with each closure and you could sometimes hear that sound from across the room!!
Of course, THAT sound would have been a negative for James but a sure sign of success for a patient who would have otherwise died from valvular heart failure.
Great work, my friend!!
Thanks
Wow 🎉🎉🎉 now this engine is running in its 61st hour I'm at all this might be with the best the absolute best video on all of CZcams reason why because it's valuable because you just talk people that hey guess what is a small engine repair whole class baby from beginning to end this is how you get it done very awesome definitely people are going away and this has helped them I'm sure of it probably people out there with small engines and going why doesn't it work and you're going to and then they're going to watch this video oh well that's what's wrong with it
I like your second option their of bending the top of that pin down so that as you put in that piece of metal when you go to walk out with that slide hammer it will hold on to their
mr. James I did see the first video. But I’m in the middle of servicing swimming pools at the moment but tonight I will sit down in my rocking chair and I will watch your amazing transformation of a broken engine to a running viable generating unit.😊
Place in 1950 here on your time in this wonderful awesome video I was thinking drill press. I don't know something about those pens are not coming out of that engine.
You redesign them according to the parts you have. Its an amazing skill James.
I went to the dentist recently. Swear to God he did the exact same thing to rebuild my teeth. I think he even uses the same tools. Now my choppers are up and running again.
I smiled almost as much as you probably did when it started on the first pull.
Good job. Thanks
I would have been tempted to spray that new odd head gasket with aluminum spray paint to be sure to get a good seal.
Excellent job James. I just sold a Hemi engine to someone a month ago. They usually run really well. Hope to see that one on a machine soon. Thanks for the video.
Is James Condon the Eric O. of small engines?
Or is Eric O. the James Condon of cars..?
Either way I love me a 90mins of JC.
I have learned so much from this channel.
Another MasterClass edition to these venerable 389cc engines. Thanks James, really enjoyed this one!
Had nothing but confidence in your skills James 😊
Finally, after watching the news, I can find some sanity... We are a dying breed... Great work as always....
My dad had an old Kawasaki five horsepowers four stroke single cyl side valve engine sitting in his garage with no head, I asked him if he had the head for it and I found it but there was no head gasket. I asked him if he had some thin aluminium sheet which he did so I cut a head gasket out of it using tin snips, fitted it and bolted the head down and there was compression and no leaks so I made sure there was spark and I put some fuel in the tank and pulled it over, she fired up and ran beautifully. Dad was most impressed.
Old school tip for those pesky dowels. Find a bolt that just barely fits inside the dowel. Then you can use vise-grips to squeeze the dowel against the bolt tightly. Now you have something to pull on. You can turn the vise-grips and the bolt at the same time to twist it out as well.
Never did like that method of valve spring retention. It's ok on side valve engines but on OHV you risk dropping a valve and that's exactly what happened here.
What an amazing mechanic and content creator JC. Would love to know how you got into this, both the Mr. Fix-It and video creation and whether you had prior training or just "following your nose" as my dad used to say.
Never thought I'd be investing an hour watching something like this.... but you're a master. All the best.
Thanks. No training on video creation or small engine repair. Just lots of reading and Google.
One of your best videos! Grats on the swap. The diagnosis and tear-down including the detailed rebuild is excellent - I learned a few tips along the way. interested in the grey drill burnishing tool. However, couldn't figure out if it was rubber or abrasive, realizing you provide affiliate links for the parts and tools in the description - glad you included the blind bearing tool, used for the removal of the alignment pins. Thank You!
The tool for cleaning the head was a 3M roloc bristle brush.
Nice job, James.
Magnificent, as usual, James! Most enjoyable! Thank-you!
Ps the donated lift makes an excellent photo stage! So, thank-you again to its donor!
Thanks John
Hemispheric heads put out the hp and the torque. Thank you James for another good rebuild vid.
Have seen someone test a hemi vs non hemi small engine and they found the same with the torque. HP difference was almost not measurable.
the camshaft and the counterweight from the hemi are maybe not exactly the same than the parallel, it work fine but maybe not so better than a "full not-hemi".
I always look forward to your videos James. You didn't disappoint!
Hi master, not sure why but i keep on watching your videos recently. But, keep up the good work!
Nice save!
Thanks!
Yes! To think that the original damage was due to an over-inserted pilot jet retainer. Wow!
I would kill to have your parts stash. Buying parts slows my process down significantly due to lack of funds. Thankfully, I acquired a parts riding mower for free the other day that will provide all the parts I need to finish three of the ones that were waiting in project purgatory, lol. After a year of chasing electrical gremlins, I finally my main project up and running again. I have enough to stay busy for a while. lol
I am so pleased to watch this video. I have watched the earlier, related video as well where you did the engine swap. I feel like I could rebuild a similar engine after investing in the needed tools and with plenty of trial and error.
A bonafide JC custom build! That thing sounds smooth as butta, man! Nice save on the cheap with salvage parts. Busy with mowers and pollen thick enough to pass for ash down here in NC. Keep em coming Jim!
Thanks 👍
About 7 or 8 years ago I had a guy bring me a chinese generator that he couldn't get to start. The valve stem broke right where the valve locks sit, and it hit the piston once, but the valve was still in the guide. I put a new head on it since the head was damaged but noticed the head gasket was put on 180 degrees from how it should have been at the factory. It was a GX390 clone. Ran great when I got done with it.
Great video! Went perfect with my morning coffee!
These Generac generators are a frequent feature on this channel. This makes me wonder if I would want one. I know it is the engine, but it appears Generac uses these engine on most of their units. Between Generac and your buddy that sends these units to you, you have job security lol. Love the channel, very detailed and explanatory.
In there are a lot of generacs out there. I think most of it is user error and neglect.
@@jcondon1 Yeah, any brand with succumb to both of those reasons. With hurricane season approaching here in Florida, there are going to be a lot of folks running into issues from neglecting their machines.