Video není dostupné.
Omlouváme se.
How To Replace The Power Steering Gear Box On A Jeep Wrangler Tj
Vložit
- čas přidán 16. 08. 2024
- Brian Eslick from How to Automotive www.howtoautomo... takes you step-by-step through the process of replacing the power steering gear box on a 1997-2004 Jeep Wrangler.
Affiliate link mentioned in the video for Remanufactured Genuine OEM Power Steering Gear Box Gearbox For Chevy GM AMC Jeep - BuyAutoParts 82-00305R New amzn.to/2qqUY1x
Affiliate link mentioned in the video for Genuine Mopar Fluid 68218064AB Power Steering Fluid - 1 Quart amzn.to/2qnhrAR
Affiliate link mentioned in the video for Permatex 24300 Surface Insensitive Threadlocker Blue, 0.34 oz. amzn.to/2qrbWg4
Affiliate link mentioned in the video for OTC 7314A Pitman Arm Puller amzn.to/2qvmkTf
Affiliate link mentioned in the video for Milwaukee 2763-22 M18 1/2" Inch Impact Wrench amzn.to/2s2sIDK
Affiliate link mentioned in the video for Milwaukee 2457-21 3/8-in Cordless M12 Lithium-Ion Ratchet Kit amzn.to/2rETlhP
Affiliate link mentioned in the video for Milwaukee 2754-22 M18 Fuel 3/8" Impact Wr- Xc Kit amzn.to/2p7ktEs
Website
For more videos, tips, and to purchase recommended tools and products visit my website at: www.howtoautomo...
Stay connected at:
Email: howtoautomotive@gmail.com
Facebook: / how-to-autom. .
Google+: plus.google.co....
LinkedIn: / brian-esl. .
Disclaimer
Owing to factors beyond the control of How to Automotive/Brian Eslick, it cannot guarantee against unauthorized modification of this information, or improper use of this information. How to Automotive/Brian Eslick assumes no liability for property damage or injury incurred as a result of any information contained in this video. How to Automotive/Brian Eslick recommends safe practice when working with power tools, automotive lifts, lifting tools, jacks and jack stands, electrical equipment, blunt instruments, chemical lubricants, or any other tools or equipment seen or implied in this video. Because of factors beyond the control of How to Automotive/Brian Eslick, no information contained in this video shall express or imply warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or information contained in this video is the sole responsibility of the user and not How to Automotive/Brain Eslick. #howtoautomotive #AutoRepair
2007 is a JK, totally different gear box. In fact 2003-2006 use a different gear box too. Basically the same process, but you can access the lines on the box by simply removing the sway bar cover. As for bleeding, you can simply jack the front end up and turn the wheels all the way left and right WITHOUT starting the engine... this helps prevent fluid starvation if you don't keep close eye on the level while bleeding.
Video is years old but still relevant. Noticed the box leaking and contemplated taking it to a shop. Now i see this is really something i can do myself. Thx!
Whenever I’m doing a job and you have a video about it I feel a lot more confident doing it. Good video
Great video. I’m a novice and new to Jeeps. I noticed my power steering box is leaking. You made me feel confident in doing this myself.
Thanks for making this video clear and concise, Brian!
bkell1011 thank you for watching!
Great instruction. I especially like using your leg to raise the jack.
Glad you like the video. Thank you for watching!
Thank you sir, my 1997 looks the same. I'm always working alone so this helps.
97-06 Jeep Wrangler TJ. Very good video! Thank you!
pretty sure power steering boxes changed to the Mercedes box in 02
Good job to the point and no BS 👍🏼👊🏼 thanks for sharing
Looks like you're helping me with my weekend project haha thanks for the video man
Awesome glad video is going to be or some help. Good luck and thank you for watching!
I have an '05 TJ Rocky Mtn and the steering has been an issue for a while now. It only has a 2" lift, 32" KO2's with 22lb alloy baja rims. Not even 70lbs total with the tire and rim. I have the Currectlync tie rod and drag link, Fox steering stabilizer and M.O.R.E steering box brace. I know these Mercedes gearboxes are not as good as the Saginaws but would it fail with this modest set up? I had the gearbox tightened between an 1/8 - 1/2 turn about a year ago. It helped but went off road recently and now the steering is starting to get a bit sloppy and wonky again. It has never leaked any oil that I know of, I'm the second owner.
I laughed pretty good when you used your leg, I have done the same thing many times. But love the video, it saved me a ton of time and headaches.
Thank you for this great video! As soon as the parts come in, I’m going for it. Hella appreciate the help!
Great video!! Thank you for providing this. It was very helpful.
Wow so fast and easy earned a subscriber
The new input shaft flat spot doesn't align exactly with the position of the old one. Do I turn the new input shaft slightly? What will be the impact on the pitman arm alignment?
Great video, I like how you show that milwaukee tools are a time saver. I do that in my videos as well
Jursaw nothing more important than saving time.
How to Automotive I don't like lugging around an airline either
Jursaw me either. These tools to make automotive technicians mobile
When the Pittman arm puller starts bending get the torch it doesn't have to glow red just start smoking a little to get it give up but this is extreme cases. Like a last resort.
Best how to video. Super job man!
Best video I have seen on this yet! Thanks
Awesome Vid.. You got mad skills :) I got a ZJ that I need to do and I'm sure it's the same procedure.
Just did my steering gear box. Takes two people to do it. It’s heavy to handle.
But can’t find a single video on how to fix the backup light switch on side of transmission. Impossible to get to or unclip the plug.
Great video. But I can't seem to find the link for the tool needed. Would you send me the link. Thanks
Where do you buy a new steering gear box? I live in Miami Fl Thanks
GreAt video keep up a good work 👌💪
Thank you!
I was looking at buying one that comes with a pitman arm attached, so would it be easier to remove the arm from the drag link instead of the box if it's already attached on the new one??
Is this a Milwaukee commercial? My DeWalt work pretty good
Thanks!
Big thanks for the very helpful video. Can I ask where you purchased the orings for the power steering lines?
If you bought a new steering gear, the new o-rings should come with it.
Mine is a 97....is it the same steps or is there something different?
Thanks
It’s going to be the same thing.
i disagree. there is not much room to loosen them. i always drop it down with my trans jack with the jeep on the lift. great video. kristopher hill work smarter not harder
terry schaefer I agree thank you for watching!
How long did this take in actual time? Nice video!
Hi ! Nice video ! What is the socket size for the pitman arm nut that connects to the steering box, thanks?
If I remember right it is a 1,5/16 And if you don’t have SAE Sockets a 33 mm should work
I i stalled mine on my 00 tj and i tried your bleeding method and it does not work. I also got a vacuum bleeder kit and i am getting air out but it seems like its air locked. Tonight i am working on it again and going to break the lines and try to get the air out and try again. Any suggestions on what to look for
Your comment is super old at this point but for anyone else who comes along and reads this thread--you're supposed to fill up the PS reservoir to the fill line, then turn the steering wheel lock to lock 10-15 times BEFORE starting the engine, and then top off the reservoir to the fill line again, THEN start the engine and lock to lock another 5-10 times or so, then check fluid again and make sure there are no bubbles.
Thanx a bunch-helped me out a lot:)
sun Tao glad the video helped. Thank you for watching!
What size socket is needed for the nut holding the pitman arm on?
Did you ever find out what size?
@@Practicaldad317 32-33mm for metric and standard size is like 1 1/4 or 1-5/16 or something like that
32 mm is a hair big but worked for me
A good sized pipe wrench will work too.
Great work up!
Richard Garcia thank you!
Thanks
Its 1997-2006
Excellent
Thank you!
Is this doable without power tools?
Want to do this myself to save $ but doesnt help if I need to buy a whole lot of gear
Quinten Murray you need power tool to remove the Pitman arm and Pitman arm puller. The rest of the job can all be done with hand tools.
Bugger
Thanks
Quinten Murray glad to help. Thank you for watching!
Quinten Murray you do not need power tools, just muscle.
half inch drive with breakerbar might work on the pitman arm/puller
Mahindra 1997 how to make power steering wheel
97-06 homie
hello can you help me get a steering box for a jeep wrangler tj 2004 4 cylinders
I don’t sell or ship parts sorry.
Says that part wont fit an 03 wrangler
03 changed to the Mercedes box
How the hell you all gonna make help videos and not mention socket sizes?????
Something I’ve added to my newer videos..
Service data doesn’t even provide that information and that’s something you pay for
nooo. everyone knows you break the lines loose before anything. as someone who works on rusty jeeps all the time I would know. and secondly if you don't unbolt the steering shaft first you wull hate yourself later. and if you cant hold the gearbox with your muscles maybe you should have someone else do it.
Hey big shot. The whole idea of lowering the steering gearbox is to get a wrench on the lines. 2000 TJ this is necessary. Disconnecrt the steering shaft not necessary.
Thanks
Thank you for watching!