With 0 mechanic experience I got an OBD2 device and got this done in less than 15 minutes. Solved all the issues. Awesome video and super easy to follow!
Also 0 mechanic experience. But had my step dad help me. He didnt have me remove the whole intake compartment. Just the part that is hose clamped on (the tube itself.) Seemed less steps that way.
Will say the thing that hung me up was not only does it use Freon 6-7x more expensive it comes in 8oz cans, and require a new set (the correct set) of gauges and tools to refill. Was able to do all the work myself and rent the tools, vacuum the line, do it all correctly and still cost me nearly 400$. Had it been the traditional 134a it would have been 60$. Be prepared!
Thank you so much! I changed the purge valve in my 2013 Focus using your video, and your explanations were crystal clear. My car had error codes P2196 and P144A before, but now they are gone. The issue was stalling and stopping when filling the car, but now everything works as it should. Thanks again!
Awesome video bro. Literally the best I ever seen on CZcams. I'm planning on tackling this job on my '18 Focus with p1450 code. Rough starts or sometimes just stalls after filling up gas tank but I've heard some people's focuses will just stall mid-drive if the problem isn't fixed. Anyways, thanks for the detailed tutorial and time you took to record and upload the video 🙂
Many thanks for the detailed video. I did replace mine as well with the slight variation that I didn't remove the whole air filter assembly, only the large rubber trubing by removing the retainers in both ends. I couldn't pull the air filter assembly enough to get it to pop and was a bit afraid not to break anything. But it all worked out fine. Many thanks again
Great video man! My check engine light came on in my 2018 ford focus and found out it was the solenoid and thanks to this video I changed it out in 5 min.
Thank you. My dad's car showed this code a few weeks ago and I was trying to find a solution to a problem he had with his oil but I could not connect the two until I saw your video. When you mentioned the code P1450 the code seemed familiar and I quickly got my OBD2 reader and pulled up the history and sure enough same code.
Thanks for the video. I have a P046 code and just swapped in the new purge valve. I did snap off one of the two the plastic mounts on the bottom of the air intake box while removing it but fixed it with duct tape ;).
Loved this video. Question. After I installed the purge valve I cleared the code but when I check my code reader there was a code for dtc definition not found. There is no code on my dash board, only the obd2 reader. Should I worry about it or just leave it alone?
After removing the hose from the throttle body and ensuring that their is no debris in it either stuff a rag in it or cover it with a plastic bag to ensure nothing falls in it. Be sure to remove the rag or plastic bag and make sure it is clean before reinstalling hose.
I've seen several videos replacing either the purge valve or the whole assembly. I'm not certain which one I should replace but I do have p1450 and p0456 codes
Thanks to the video otherwise I couldn't change the purge valve, Big Shout out to Big Ben! May I kindly ask why the engine is still on after I replaced the purge valve since I got code P0456? Will it disappear later or I should drive for a while to see...
What are the symptoms of damage to this part? Is the reason for the release of a quantity of air when inserting the fuel gun considered a symptom of damage? and it is the same location in focus 1.6 ?
Yes that could be the purge valve, but also make sure your gas tank isn't sucked up from the purge valve pulling vacuum. The dealer can check that and there was a recall on it
I have been investigating my P0420 code (catalytic converter) and see that some people are saying that replacing the purge valve will help. I am quite certain it is NOT a cat problem and related to the sensors. The code is very intermittent, it will even go on and off during a single drive. I do not have any of the sounds people say attribute to a bad cat. Any advice here?
The cat is a very common issue on these, normally they just set a p0420 code and that's it. Yes, if the purge valve is leaking it can cause the code if the air fuel mix isn't correct. You can try replacing that first, and doing a tune up..and maybe the upstream o2 sensor. If you still have the code, I'd put an o2 spacer on the rear o2. Or spend 1400 on an oem cat. Up to you lol. Aftermarket cats are cheaper but will start setting p0420 again within months
The low pressure line appears to come as an assembly with the lines going all the way to the back of the car. If you suspect just the o-ring leaking you can try matching that one up but make sure it's exact and rated for fuel
I got a p2196 code right after filling up, didnt notice it being hard to start. I'm pretty sure I had the recall done when I recieved the notice. Is it the purge valve or o2 sensor?
What size Socket ? US Standard or Metric Socket ? Thanks for showing how to change this part....I'm sure if I had the Ford Dealer do it would be $500.00
Thanks. I'm rewatching your Video. Planning to do this repair in about 15 minutes. Unfortunately I purchased a small screwdriver to loosen the clamp. And a long Screwdriver since no Cat Claw. I'm traveling for work and doing this in the Motel Parking lot. Purchased replacement part from O'Reilly Auto Parts in Georgia. Wish I had seen you reply earlier before buying tools. I have a 7mm/ Socket set at home somewhere in my Garage in NJ
Dumb question. After I cleared the code and drove around I plugged the OBD reader again and it still gives me the P0456 code but the check engine light doesn’t come on. Anything else I should try?
Just used your video to take care of my purge valve in my 2018 Focus. But I always worry that I didn't put something back right and my car will explode.
@@BigBensCarsAndCycles buying now! Thank you so much I will report back after fixing her up. I love my focus so much I’m gonna keep her for as long as I can🙌
@@BigBensCarsAndCycles I have a sound when I crank to start. I hear people’s cars sound normal crack and it starts. Mine doesn’t sound like starts it’s hitting but like if the car sounded old . Like how them old cars start their engines . Idk what it could it be
For sure. Just because Ford used plastic everywhere under my hood, doesn't mean it shouldn't be clean, and cared for. Everybody uses plastics. There is art in aesthetic design appearing in polymer parts design, by all companies still producing ICE CARS...the headers on my Fiesta....plastic-coated.... but somehow, still aesthetically pleasing.....and taking engine head covers off, keeps our engines cooler.... if you don't live in arctic conditions, you DON'T want a head cover.....@@BigBensCarsAndCycles
Dorman Purge Valve: amzn.to/3HVOBgh
My ford focus is 2015 SE 4 cylinders 1.5 L echo boost had turbo oil leak after 110 k miles due to using bad oil or different oil … I think
With 0 mechanic experience I got an OBD2 device and got this done in less than 15 minutes. Solved all the issues. Awesome video and super easy to follow!
Awesome! Glad to help
With 6 out of 10 mechanical experience it took me about the same. Great instructions honestly.
Also 0 mechanic experience. But had my step dad help me. He didnt have me remove the whole intake compartment. Just the part that is hose clamped on (the tube itself.) Seemed less steps that way.
Will say the thing that hung me up was not only does it use Freon 6-7x more expensive it comes in 8oz cans, and require a new set (the correct set) of gauges and tools to refill. Was able to do all the work myself and rent the tools, vacuum the line, do it all correctly and still cost me nearly 400$. Had it been the traditional 134a it would have been 60$. Be prepared!
Damn. Sitting at the dealership at this moment and I could’ve saved myself a bunch of money had I found this video sooner.
I think this has to be the best tutorial I’ve ever seen on CZcams about anything. Your frickin rock dude!
Awesome! I'm glad it helped
I have zero mechanic experience and your video helped me to replace mine in 20 minutes.
Thanks sir 😁
Thank you so much! I changed the purge valve in my 2013 Focus using your video, and your explanations were crystal clear. My car had error codes P2196 and P144A before, but now they are gone. The issue was stalling and stopping when filling the car, but now everything works as it should. Thanks again!
Awesome! Glad you're all set. Happy driving!
@@BigBensCarsAndCycles may I kindly ask what should I do for P0131 (02 Sensor Circuit Low Voltage Bank 1 Sensor 1) code? Thank you so much!
@@taunus1979 install a new oem or Bosch upstream o2 sensor. You're welcome!
@@BigBensCarsAndCycles perfect, subscribed and will check all the content. There are lots of useful tips in the channel. Thanks again!
Great job in explaining how to replace the purge valve now I'll tackle the job, thanks a bunch.
i know nothing about cars and this was so helpful and easy to follow. thank you!
Awesome video bro. Literally the best I ever seen on CZcams. I'm planning on tackling this job on my '18 Focus with p1450 code. Rough starts or sometimes just stalls after filling up gas tank but I've heard some people's focuses will just stall mid-drive if the problem isn't fixed. Anyways, thanks for the detailed tutorial and time you took to record and upload the video 🙂
You're welcome!
any update on if this worked for you?, having the same issue in my 2018 focus
Many thanks for the detailed video. I did replace mine as well with the slight variation that I didn't remove the whole air filter assembly, only the large rubber trubing by removing the retainers in both ends. I couldn't pull the air filter assembly enough to get it to pop and was a bit afraid not to break anything. But it all worked out fine. Many thanks again
You're welcome! And good idea with that hose!
Great video man! My check engine light came on in my 2018 ford focus and found out it was the solenoid and thanks to this video I changed it out in 5 min.
Awesome! Glad to help
Thank you. My dad's car showed this code a few weeks ago and I was trying to find a solution to a problem he had with his oil but I could not connect the two until I saw your video. When you mentioned the code P1450 the code seemed familiar and I quickly got my OBD2 reader and pulled up the history and sure enough same code.
You're very welcome!
Over 1k subscribers!!! That’s awesome
I appreciate it so much!
Thanks for sharing this video. Very well described. Got mine done in about 30 minutes.
You're welcome! Glad to help
Thanks for the great video, exactly what I needed and it went very smoothly with your help.
Awesome! Glad to help. Happy driving
Thanks for the video. I have a P046 code and just swapped in the new purge valve. I did snap off one of the two the plastic mounts on the bottom of the air intake box while removing it but fixed it with duct tape ;).
Straight to the point great tutorial
You're welcome! Thanks for watching
That's a lotta acorns! Great video
Dude youve got a sub. Thanks for making a video i can follow along with so well.
Happy to help!
DE TODOS LOS VIDEO ESTE ES EL MEJOR EXPLICADO,,,LOS DEMAS TIENEN QUE VER ESTE ..PARA QUE HAGAN LOS VIDEOS ASI CON SUS DETALLES,,,,(GRACIAS MILL)
de nada! muchos gracias para ver (lo siento por mi espanol)
Extremely helpful. Thank you sir!
Youre welcome!
Great vids. Sounds like someone who used to teach kindergarten
Do you have the part number on the abs wheel speed sensor for passenger side
Thanks for the help. I hope that fixes it
It will fix codes p1450 and p0456. Also several other symptoms and codes. What issue are you having?
What size socket do u use
Loved this video. Question. After I installed the purge valve I cleared the code but when I check my code reader there was a code for dtc definition not found. There is no code on my dash board, only the obd2 reader. Should I worry about it or just leave it alone?
did it give you a code number or anything? I'd probably not worry about it
After removing the hose from the throttle body and ensuring that their is no debris in it either stuff a rag in it or cover it with a plastic bag to ensure nothing falls in it. Be sure to remove the rag or plastic bag and make sure it is clean before reinstalling hose.
I've seen several videos replacing either the purge valve or the whole assembly. I'm not certain which one I should replace but I do have p1450 and p0456 codes
You should get a bv6z-9d289-r (oem purge valve). That's all you'll need.
@@BigBensCarsAndCycleshi i just if the Dorman 911-777 Vapor Canister Purge Valve the same thing as Bv6Z…
Hey there, trying to do this myself now, and what's the size of the socket and/or the name of the powered wrench you're using? Great vid btw
I'm glad the video helped! It's a Milwaukee m12 1/4" ratchet
Thanks to the video otherwise I couldn't change the purge valve, Big Shout out to Big Ben! May I kindly ask why the engine is still on after I replaced the purge valve since I got code P0456? Will it disappear later or I should drive for a while to see...
I'm glad it helped. You can clear the code with any cheap scan tool
Did the code go off after you replaced it?
Thanks for the video! But wouldn't have been easier to just remove the intake hose?
Yup! You can do that too.
What are the symptoms of damage to this part? Is the reason for the release of a quantity of air when inserting the fuel gun considered a symptom of damage? and it is the same location in focus 1.6 ?
Hi, the 1.6 is similar. The failed purge valve can cause engine lean or rich depending on how much fuel its pulled through the canister
My fuel gauge indicates more fuel than it should. The marker never indicates fuel in reserve. Would the problem be the purge valve?
Yes that could be the purge valve, but also make sure your gas tank isn't sucked up from the purge valve pulling vacuum. The dealer can check that and there was a recall on it
Wow great video thank you so much.. is this the same as the EVAP purge valve? Thank you
You're welcome, and yes - it's the same part
@@BigBensCarsAndCycles thank you my engine light was on yesterday and its about that according to autozone.. but today the light turns off.. its weird
I have been investigating my P0420 code (catalytic converter) and see that some people are saying that replacing the purge valve will help. I am quite certain it is NOT a cat problem and related to the sensors. The code is very intermittent, it will even go on and off during a single drive. I do not have any of the sounds people say attribute to a bad cat. Any advice here?
The cat is a very common issue on these, normally they just set a p0420 code and that's it. Yes, if the purge valve is leaking it can cause the code if the air fuel mix isn't correct. You can try replacing that first, and doing a tune up..and maybe the upstream o2 sensor. If you still have the code, I'd put an o2 spacer on the rear o2. Or spend 1400 on an oem cat. Up to you lol. Aftermarket cats are cheaper but will start setting p0420 again within months
How do you replace the fuel line to the high pressure fuel pump? My ford focus is leaking fuel from the line
The low pressure line appears to come as an assembly with the lines going all the way to the back of the car. If you suspect just the o-ring leaking you can try matching that one up but make sure it's exact and rated for fuel
I got a p2196 code right after filling up, didnt notice it being hard to start. I'm pretty sure I had the recall done when I recieved the notice. Is it the purge valve or o2 sensor?
It is possible they reprogrammed your car but didn't replace the purge valve because it wasn't bad then
I pulled the line off and it didnt have any vacuum so. I did clear the code right after so will have to wait and see if it pops up again
What size Socket ?
US Standard or Metric Socket ?
Thanks for showing how to change this part....I'm sure if I had the Ford Dealer do it would be $500.00
You're welcome! 7mm for the hose clamp on the air intake hose (8mm on 2012s)
Thanks.
I'm rewatching your Video.
Planning to do this repair in about 15 minutes.
Unfortunately I purchased a small screwdriver to loosen the clamp.
And a long Screwdriver since no Cat Claw.
I'm traveling for work and doing this in the Motel Parking lot.
Purchased replacement part from O'Reilly Auto Parts in Georgia.
Wish I had seen you reply earlier before buying tools.
I have a 7mm/ Socket set at home somewhere in my Garage in NJ
@@YuTbCensorship it'll be fine. The clamp has a flathead screwdriver provision
Dumb question. After I cleared the code and drove around I plugged the OBD reader again and it still gives me the P0456 code but the check engine light doesn’t come on. Anything else I should try?
It may be reading it as a permanent dtc and you'll need to complete the readiness monitor for it to clear. It'll do that on its own in a few days
@@BigBensCarsAndCyclesOk thanks for the response😁
How do you pull the hose off the throttle body? I lossened it but still stuck
Hi, you can run the engine with the hood closed to warm the rubber. Or use a blow dryer
Any advice on how to actually disconnect the part? I cant get those green conectors to come off on either side
@@OfficialFTG push the hose inward, push down on the release, then slide it off
So where exactly is it under the air filter box or what sorry I’m
Dumb founded as I no mechanic
Removing the airbox only helps with removing it and it's not totally necessary
Is this why my focus is hard to start after putting gas in it? No check engine light
Yes, most likely
@BigBensCarsAndCycles thank you so much. You're videos have been amazing to get to know my new car
Can this part possibly cause the engine to knock?
If it leans the engine out enough it's possible
Where does the transmission vent connects to?
It slides into a hole near the range sensor
Just used your video to take care of my purge valve in my 2018 Focus. But I always worry that I didn't put something back right and my car will explode.
I'm glad it helped, you'll be fine!
what was the code your's was throwing before you fixed this issue?
I was stressing at first. I swapped the purge valve out and the code wouldn’t go away. I didn’t realize I had to clear it first 😂
Glad you got it fixed 👍
Hi ben. What tools do I need for this?
1/4" ratchet, 7 or 8mm socket for the air hose clamp on the throttle body, flat head screwdriver to reach the clip for the purge line on the intake
@@BigBensCarsAndCycles buying now! Thank you so much I will report back after fixing her up. I love my focus so much I’m gonna keep her for as long as I can🙌
Man. Could not get the left green thing off. Not sure if its broken or what but I’m not sure what else to try
Sorry to ask … what is OBD2 …??
Vehicle link interface for a scan tool. The plugin under the dash
Thank you 🙏 brother
Why was it replaced ?
P1450 is the most common code for it. It can also cause a lean or rich condition. Depending on if the canister is flooded.
@@BigBensCarsAndCycles I have a sound when I crank to start. I hear people’s cars sound normal crack and it starts. Mine doesn’t sound like starts it’s hitting but like if the car sounded old . Like how them old cars start their engines . Idk what it could it be
@@Inkadomination I just saw your comment. If you want to post a short video of that on my discord I'll take a listen
I replaced mine 2 years ago and this came up again :/
Did you use oem? That should last 5 years plus
Poor abused girl. 😥 All the grunge says it all....then the fact nature decided that was a new home to move into.....
If it were mine, I'd take great pleasure in cleaning that all up
For sure. Just because Ford used plastic everywhere under my hood, doesn't mean it shouldn't be clean, and cared for. Everybody uses plastics. There is art in aesthetic design appearing in polymer parts design, by all companies still producing ICE CARS...the headers on my Fiesta....plastic-coated.... but somehow, still aesthetically pleasing.....and taking engine head covers off, keeps our engines cooler.... if you don't live in arctic conditions, you DON'T want a head cover.....@@BigBensCarsAndCycles
Who on Charlotte that can come replace mine
air blow the engine sir!!
Owners problem, not mechanics
The real story here is how the creator pronounces "debris".
Debrisss