@@JARG I am stuck on something else though. I'm still having FTF issues. I have tried the recoil springs with no success. Last time out at the range it seemed like the pistol would cycle fiocchi ammo about 75% without a problem. Everything else cause jam after jam. Having a hard time narrowing this issue down.
I know this video is old now but you are golden for this. Just fixed my issue. 100 percent engagement each time now. Solid click. You’re doing gods work. Thanks 🙏🏾
Señor regular guy u just saved me big money lol earlier today at the range I was getting so many dead trigger/ fail to reset and this right here help 🙌🏽🙏🏽
Hey bud, thanks for pushing to exercise our rights and not giving in to those forces that wanna strip us from our givin'rights and personal hobbies. I love your help and demonstration on the issues that we tend to run into on some builds. You make em' and I'll keep learning new things by watching them. Thanks for this trigger fix too!👍🏽
Figured I'd add what fixed my gun here too. Maybe every 1 in 5 wouldn't reset properly. I tried grinding down that small section by the rear rail insert where the trigger bar touches it, but ended up taking way to much off and made my problem worse! I tried bending the crucifix every so slighrly and still had the problem. I then tried grinding down the polymer inside the frame were the teigger bar meet does a 90 but that didnt help either. By this point now, almost every other reset wouldn't happen after racking the slide. Luckily, I just so happen to have a new 3.5 connector and heavier trigger reset spring coming in. After installing those, it completely resolved my issue, even with the messed up grinding I did. I still ordered a new rear rail since it was royally messed up with my handy work. Figured Id comment this in case anyone has tried everything and is looking for other suggestions.
Thank you for the video, I didn’t have the 80% lower, but I did have the GSX100 from the Glock Store same problem trigger not resetting I followed your video so far 185 rounds with only one failure, taking it again to the range this Saturday, going to shoot more then 200 rounds, if I get one failure to reset, I’ll adjust the trigger bar one more time.
I remember my neighbor had a G19 that wouldn't reliably reset if the trigger was held down a bit firmly because the slide wouldn't be able to push the disconnector over. The crucifix seemed to catch the FP just fine on cycling, but only if the bar had reset per the slide pushing the disconnector off of it. I didn't think it was possible for the slide to NOT push the disconnector over, but I guess the trig bar will just flex over with it if it's pushed into the disconnector hard enough and not slip out from under it as it's supposed to. I don't know if he ever figured out how to remedy it but polishing the end of the bar like this seems like it'd do the trick.
Thanks, this helped. My trigger would reset occasionally but most of the time it wouldn't. After watching this, I pushed down hard on the slide while racking it and it resets every time I do it that way. Guess I'll get to bending.
I'm glad I ran across this video because it affirmed what I narrowed the problem down to being. I'm gonna give it a go in the morning and see if this does the trick. Side note on the end of the video, so you mean you don't show how to make fully semi-automatic assault weapons here? 😂.
Now ya tell me! Had to figure that out by trial and error. But yeah, mine was flat and firing pin would not grab to reset trigger. Used a vise same as you did.
Love your mindset. I've watched all three videos now. That recoil spring didn't fix your problem, it overcomes it with force. The problem is that Rock Slide. I know I have several. The firing pin channel is burred. Pull your firing pin and see if it slides all the way out and back in with ease. If it doesn't there are burrs inside from the machining. Look at the block at the head of your firing pin, is there scaring from the firing pin channel?
I previously built a 80% arms G19 size frame with zero problems. Just finished polymer 80 G17 size frame with what appears to be the same slide as you and it's a constant failure to fire and the trigger doesn't reset so I have to release the striker from the rear to disassemble it. Thinking about pulling the trigger from my other build and trying it.
This video definitely helped me fix my trigger reset issue without the mag inserted. However once I insert the mag I get the same reset failure. Do I just need to bend the bar a little more to allow it to engage the striker with the mag inserted?
I’ll have to use an actual vice like you did. I just tried heating it up and bending it with pliers, which worked a little bit but I did have some difficulty getting a good grip on it.
So I just build my 1st P80 and have this issue. It would reset, 1 out of 10 trys.I broke my bar that came in my kit, so I went out and bought a CMC $170 trigger. It worked for 5 times exactly and then quit all together. So I've bought another p80 frame and am going to. Try leaving the rear rails you Mill down a little higher. What you think?
@JARG you are a 100% right. I had an oem bar I bought I've been sitting on. It didn't work until I did what you said this morning. And Bingo, I got a working glock. I haven't fired it yet, but at least now the trigger works. I did heat mine red hot and then quenched it in 40w oil and polished
I’m having issue with my build slide wont go into full battery sometimes but a little bump or sometimes if I let the trigger go or if I just wait or if I drop the slide normally not slowly It will go into full battery I think it’s something with the trigger assembly but I can’t pinpoint what’s wrong I compared it to my other build that works great and it’s all the same I even swapped the safety plunger and it works in my build that was already working good
@@JARG it stopped having that issue not sure what fixed it just took it apart and put it back together now the slide stop lever catches just barely sometimes when I have a loaded clip in it but when there’s no clip it doesn’t catch I sanded the inside where it sits down a little so it doesn’t have down movement and it still catches occasionally
Do you happen to ever have any issues with the p80 g43 single stack triggers and the overall functionality of it? I'm having a lot of trouble trying to get one to work. How do I get in touch with you?
So should I bend mine the other way mine won't fire. It acts like the trigger is hanging on something is hold it from dropping. If you look in between the slide and frame. You can kinda see the extractor rase up a little and the trigger won't pull. Plz help. I'll give you my number to text or call if need be. I want to learn how to get it right. I've tried 2 diffrent triggers so it might be my frame. Thanks in advance
Great knowledge man! I have that issue with my g19 (all parts OEM) only when i rack the slide very hard and fast..when i manipulate it "the normal" way, everything is OK..but WHY??? Do you have an advice? Best regards from germany! Stay safe over there:)
I'm having an issue with my p80 build. The trigger resets but it is not releasing the striker sear, so it won't fire and it makes taking the gun apart to look at it very difficult. Any ideas?
Get a dremel, some cotton polishing bits for it, and some polishing compound. Polish sear/anvil and striker lug until super smooth. Polish everything else while you're at it. (See Johnny Glock videos). Drop of oil. If that doesn't do it, your sear may be too engaged. If so, do the opposite of what this guy recommends. You want 80-100% engagement, or so I'm told. More makes it hard or impossible to release. Less makes it dangerous.
I took my fresh g19 build out to the range and it would double fire everytime, but the trigger wouldn't reset and the casings were extracting. I'm trying to figure out why this would be happening. Any ideas?
Hey buddy, I tried your fix on my 43 p80 and the rear part of the cross member is not moving even with heat. Is there another way or option? Please let me know, thanks and have a great day.
My issue is that i brought all glock parts , had a few light trigger pulls but my main issue is that once it chamber another round it fires after i release the trigger , only put 100rnds through it. My regular g22 mag cycled with no hiccups or miss fires. So im confused?
Sound like you got issues. The problem sounds like the mag and trigger bar are pressing your slide up and causing the firing lug to slip over the cross bar.
So this didnt fix my issue, i thought it would. I believe my issue is the metal spring bar that sits on the trigger. If i hole the slide on one side it resets and hold it to the other it wont so the slide isnt engaging the flat spring far enough to allow the trigger bar to raise up. So if anybody else is having this issue check that its not this either. Because there isnt a lot of material to grab and bend im going to have to grind one of the flanges down
Update so the issue was the trigger connector i believe it is called, the small bent flange had to be filed a couple thousandths to allow the trigger bar to move up when contacting the slide. If i put pressure on the slide to the right as a racked it the connector wouldnt engage fully and allow the trigger to reset.
Is this the reason possibly why my new p80 build fires 5 rounds at once if five rounds are in the magazine or two rounds almost like a double tap if there's only two rounds in the magazine it seems to Auto fire
I have a p80 build and my trigger respond or anything . I’ll rack my slide and it will not even let me push down on trigger at all . Any suggestions ?.. need help
I built 19 P80 builds and only the last 4 I've had the same problem with the sear not catching the striker lug I don't know if they changed the way they were stamping out the trigger bar or something???
Hey bro , whenever I pull the trigger with a round chambered it won’t fire it even when I rack the slide and load another round in it won’t fire . Do you know what’s up?
My trigger only doesn't reset when I hold it down hard. This is compared to my other Glock that would reset even when I held the trigger down completely. Any ideas?
these people have no clue what they are talking about, its a shame this is what youtube has come to.... make sure you move all of your content over to rumble like everyone else is doing.
This video resolved my issue with my P80 burst firing. For the life of me I could not figure it out until I saw this. Thank you!
Glad I could assist. Plz Like, Sub, and tell haters that these methods work.
@@JARG I am stuck on something else though. I'm still having FTF issues. I have tried the recoil springs with no success. Last time out at the range it seemed like the pistol would cycle fiocchi ammo about 75% without a problem. Everything else cause jam after jam. Having a hard time narrowing this issue down.
Don't let CZcams screw with your motivation brother you do great work!
I did know that was the problem, I replaced the trigger bar which didn’t always work. Glad to know this Saftey tip.
That is what I needed to diagnose my recent build! Can’t wait to try that so my gun is reliable vs a 40% reliable now. Thank you.
I really needed this video to fix my reset problem and make my gun safer. Thank you so much!
I know this video is old now but you are golden for this. Just fixed my issue. 100 percent engagement each time now. Solid click. You’re doing gods work. Thanks 🙏🏾
Like, Subscribe, hit the bell. I have plenty of videos to entertain
Thank you so much for helping us enjoy our sport safely! Your tips fixed the issue!
Thank you for all your efforts sir. Videos like this makes us all safer as we make the firearms safer and more reliable.
Señor regular guy u just saved me big money lol earlier today at the range I was getting so many dead trigger/ fail to reset and this right here help 🙌🏽🙏🏽
Hey bud, thanks for pushing to exercise our rights and not giving in to those forces that wanna strip us from our givin'rights and personal hobbies. I love your help and demonstration on the issues that we tend to run into on some builds. You make em' and I'll keep learning new things by watching them. Thanks for this trigger fix too!👍🏽
Thanks a lot finally after 3 months of troubleshooting I got it working properly thanks to you. I appreciate it a lot
might be, fixer up video of the year
Figured I'd add what fixed my gun here too. Maybe every 1 in 5 wouldn't reset properly. I tried grinding down that small section by the rear rail insert where the trigger bar touches it, but ended up taking way to much off and made my problem worse! I tried bending the crucifix every so slighrly and still had the problem. I then tried grinding down the polymer inside the frame were the teigger bar meet does a 90 but that didnt help either. By this point now, almost every other reset wouldn't happen after racking the slide. Luckily, I just so happen to have a new 3.5 connector and heavier trigger reset spring coming in. After installing those, it completely resolved my issue, even with the messed up grinding I did. I still ordered a new rear rail since it was royally messed up with my handy work.
Figured Id comment this in case anyone has tried everything and is looking for other suggestions.
One more grateful new viewer, thanks to this video I've fixed my issue thanks
Thank you for the video, I didn’t have the 80% lower, but I did have the GSX100 from the Glock Store same problem trigger not resetting I followed your video so far 185 rounds with only one failure, taking it again to the range this Saturday, going to shoot more then 200 rounds, if I get one failure to reset, I’ll adjust the trigger bar one more time.
Super helpful videos. Thanks for sticking to your guns!
Thank you so much for this video, this is exactly what I needed to fix my build!
Nice rockslide! I have one on my PF45 G20sf build and love it.
Yep! I believe this is the issue. Thanks! 🙏
Great information I'll try that little later. SCT frame.
I remember my neighbor had a G19 that wouldn't reliably reset if the trigger was held down a bit firmly because the slide wouldn't be able to push the disconnector over. The crucifix seemed to catch the FP just fine on cycling, but only if the bar had reset per the slide pushing the disconnector off of it. I didn't think it was possible for the slide to NOT push the disconnector over, but I guess the trig bar will just flex over with it if it's pushed into the disconnector hard enough and not slip out from under it as it's supposed to. I don't know if he ever figured out how to remedy it but polishing the end of the bar like this seems like it'd do the trick.
Great info. Worked perfectly. Great knowledge. Keep it safe.
Thanks, talked to a few people and they had same issues and ill try this and see how it works.
Short and sweet. Good video
Thank you brother gonna give this a go and see how it works everything seems to be fine besides my trigger reset
Thanks, this helped. My trigger would reset occasionally but most of the time it wouldn't. After watching this, I pushed down hard on the slide while racking it and it resets every time I do it that way. Guess I'll get to bending.
Great job on the video I’m with you they will not silence us. Thank you
That's exactly right they know nothing about firearms you helped me fix my Glock I appreciate you. Hang in their
I'm glad I ran across this video because it affirmed what I narrowed the problem down to being. I'm gonna give it a go in the morning and see if this does the trick.
Side note on the end of the video, so you mean you don't show how to make fully semi-automatic assault weapons here? 😂.
Doing good work man sucks youtube is so anti
Thanks for helping us stay safe
Now ya tell me! Had to figure that out by trial and error. But yeah, mine was flat and firing pin would not grab to reset trigger. Used a vise same as you did.
Great knowledge here🙏
Thank you so much for this information! Would this fix address the firing of multiple rounds?
Awesome video, glock builder myself and the info is the best
Like and Sub. Watch all my others!
Keep up the good work
Great explanation!
Fixed my issue in under a minute! Great videos
Like and sub
Thank you sir! This helped my problem totally!!!
Like and subscribe then
Thank you so freakin much! I am subscribing
Having same problem and scared the shit out of me at the range lol
So was it full auto? 🤣
Love your mindset. I've watched all three videos now. That recoil spring didn't fix your problem, it overcomes it with force. The problem is that Rock Slide. I know I have several. The firing pin channel is burred. Pull your firing pin and see if it slides all the way out and back in with ease. If it doesn't there are burrs inside from the machining. Look at the block at the head of your firing pin, is there scaring from the firing pin channel?
You weren't shittin when you said that it was brittle. Going to have to find my box of parts now.
I'm gonna give this a go. I bought two new triggers and sorta thought this might be the problem. We'll see thanX.
Don’t over torque. It will break
yeah scary I'll heat it up and try to be careful. There is a lot of meat on the connector arms.
Your the man fixed mine works great 💪
Tell my boss. He never believes me. Like Sub watch all my videos
Thanks that's exactly what mine was doing 👍👍👍
Awesome, that worked great! Thanks for the help!
Like and sub
Nice explanation thank you
Thank you Sir
Thanks bro fixed my g17 I had in the closet because of dead trigger issue
Great video! Thanks for sharing.... Quick question, what trigger is that in your video? It looks good...is that burnt bronze??
Don’t remember. Nothing special. Some no name
Thanks this helped i had the same problem
Glad I could help
Nailed it. Thanks......🎉
CZcams and Facebook be like 🖕🏾 your freedom of speech
Thanks
I previously built a 80% arms G19 size frame with zero problems. Just finished polymer 80 G17 size frame with what appears to be the same slide as you and it's a constant failure to fire and the trigger doesn't reset so I have to release the striker from the rear to disassemble it. Thinking about pulling the trigger from my other build and trying it.
Trigger reset is your crossbar angle. Fail to fire is because of your recoil spring and slide creep
you just helped me out thanks
Sub and share
Good deal. Subbed, man!
Bless you bro!
This video definitely helped me fix my trigger reset issue without the mag inserted. However once I insert the mag I get the same reset failure. Do I just need to bend the bar a little more to allow it to engage the striker with the mag inserted?
Yes. Sounds like the mag is pushing up on the slide
I’ll have to use an actual vice like you did. I just tried heating it up and bending it with pliers, which worked a little bit but I did have some difficulty getting a good grip on it.
So I just build my 1st P80 and have this issue. It would reset, 1 out of 10 trys.I broke my bar that came in my kit, so I went out and bought a CMC $170 trigger. It worked for 5 times exactly and then quit all together. So I've bought another p80 frame and am going to. Try leaving the rear rails you Mill down a little higher. What you think?
Still think it’s the cross bar angle
@JARG you are a 100% right. I had an oem bar I bought I've been sitting on. It didn't work until I did what you said this morning. And Bingo, I got a working glock. I haven't fired it yet, but at least now the trigger works. I did heat mine red hot and then quenched it in 40w oil and polished
❤❤❤GOON SQUAD❤❤❤
Great stuff. Go 2A
Thank you.
Your welcome. Please like, subscribe, and tell others. We here to help each other.
I’m having issue with my build slide wont go into full battery sometimes but a little bump or sometimes if I let the trigger go or if I just wait or if I drop the slide normally not slowly It will go into full battery I think it’s something with the trigger assembly but I can’t pinpoint what’s wrong I compared it to my other build that works great and it’s all the same I even swapped the safety plunger and it works in my build that was already working good
Sir I know what is wrong 100%
czcams.com/video/H1qZDmd3LNk/video.html
When it works let me know. Then LIKE, SUBSCRIBE, and SHARE
@@JARG it stopped having that issue not sure what fixed it just took it apart and put it back together now the slide stop lever catches just barely sometimes when I have a loaded clip in it but when there’s no clip it doesn’t catch I sanded the inside where it sits down a little so it doesn’t have down movement and it still catches occasionally
Do you happen to ever have any issues with the p80 g43 single stack triggers and the overall functionality of it? I'm having a lot of trouble trying to get one to work. How do I get in touch with you?
Send me your contact info to justaregularguy21@gmail.com
So should I bend mine the other way mine won't fire. It acts like the trigger is hanging on something is hold it from dropping. If you look in between the slide and frame. You can kinda see the extractor rase up a little and the trigger won't pull. Plz help. I'll give you my number to text or call if need be. I want to learn how to get it right. I've tried 2 diffrent triggers so it might be my frame.
Thanks in advance
Email me with a number
Great knowledge man! I have that issue with my g19 (all parts OEM) only when i rack the slide very hard and fast..when i manipulate it "the normal" way, everything is OK..but WHY??? Do you have an advice?
Best regards from germany!
Stay safe over there:)
Cross bar angle
Could this have something to do with a connector ?
I'm having an issue with my p80 build. The trigger resets but it is not releasing the striker sear, so it won't fire and it makes taking the gun apart to look at it very difficult. Any ideas?
Get a dremel, some cotton polishing bits for it, and some polishing compound. Polish sear/anvil and striker lug until super smooth. Polish everything else while you're at it. (See Johnny Glock videos). Drop of oil. If that doesn't do it, your sear may be too engaged. If so, do the opposite of what this guy recommends. You want 80-100% engagement, or so I'm told. More makes it hard or impossible to release. Less makes it dangerous.
I took my fresh g19 build out to the range and it would double fire everytime, but the trigger wouldn't reset and the casings were extracting. I'm trying to figure out why this would be happening. Any ideas?
Crossbar angle
👍🏻
Hey buddy, I tried your fix on my 43 p80 and the rear part of the cross member is not moving even with heat. Is there another way or option? Please let me know, thanks and have a great day.
What is wrong with your 43
I'm thinking just throwing polymer80 trash trigger group in garbage and using Glock OEM. Will this not solve the problem, too?
It will not fix the loose tolerance
My issue is that i brought all glock parts , had a few light trigger pulls but my main issue is that once it chamber another round it fires after i release the trigger , only put 100rnds through it. My regular g22 mag cycled with no hiccups or miss fires. So im confused?
Sound like you got issues. The problem sounds like the mag and trigger bar are pressing your slide up and causing the firing lug to slip over the cross bar.
@@JARG ok, so how do i fix the issue? I also brought a new guide rod and 20lbs spring after watching all three of your videos.
So this didnt fix my issue, i thought it would. I believe my issue is the metal spring bar that sits on the trigger. If i hole the slide on one side it resets and hold it to the other it wont so the slide isnt engaging the flat spring far enough to allow the trigger bar to raise up. So if anybody else is having this issue check that its not this either. Because there isnt a lot of material to grab and bend im going to have to grind one of the flanges down
Update so the issue was the trigger connector i believe it is called, the small bent flange had to be filed a couple thousandths to allow the trigger bar to move up when contacting the slide. If i put pressure on the slide to the right as a racked it the connector wouldnt engage fully and allow the trigger to reset.
Is this the reason possibly why my new p80 build fires 5 rounds at once if five rounds are in the magazine or two rounds almost like a double tap if there's only two rounds in the magazine it seems to Auto fire
Your firing pin lug is slipping over your cross
@@JARG so do you think if I do what you did in your video? That would solve that issue because mine does seem pretty flat
Tell me why I got my 43 style black frame with the fde slide ur gun looks like my gun s big brother lmao
I miss my big brother 😪💔wish he was still here
I have a p80 build and my trigger respond or anything . I’ll rack my slide and it will not even let me push down on trigger at all . Any suggestions ?.. need help
Post a video on your channel. Then show the inside of the weapon
I built 19 P80 builds and only the last 4 I've had the same problem with the sear not catching the striker lug I don't know if they changed the way they were stamping out the trigger bar or something???
@@mikehittle4649 you get what you pay for I guess...
I have a issue.the trigger break and reset is EXTREMELY close, maybe a 1/8” between the two of that...your thoughts?
Back of crossbar needs to be a little higher. Check your firing lug. I beat the wear marks are very low toward bottom
Let me know if I’m right
I'm not comfy doing that myself,I may just trade it for p320 or p365
Hey bro , whenever I pull the trigger with a round chambered it won’t fire it even when I rack the slide and load another round in it won’t fire . Do you know what’s up?
Look at your striker lug. Probably the connector is not causing the sear to fall. Or safety plunger is not being depressed
Mine seems to function fine unless I hold the trigger while pulling the slide back. Then it doesn't reset. Would this help fix my issue?
Yes
You would only need a slight bend
i have a p80 glock 26 n it fires but when it comes to shoot the next roumd the trigger is stuck
Stuck forward or backward
My trigger only doesn't reset when I hold it down hard. This is compared to my other Glock that would reset even when I held the trigger down completely. Any ideas?
Yes trigger bar angle
We’ll cross angle
Watch czcams.com/video/qGZn34vpYmg/video.html
Whats going on mann.. im having dead trigger could I be from cross bar sitting to high
What is happening. Pull and what. Moves or stuck. Spongy then reset…
@@JARG once I fire first shot next round chambers, trigger reset, but when I squeeze to it drops but doesn't fire.
I don't think it's CZcams's fault. People don't read the full guidelines It's not like most people do that because they update it everynow and then
I have decided I don't want a polymer 80. to many issues. Ill get a Glock, shadowsytems or PSA dagger
I agree. I have it for fun. Not to carry or bet my life on
What is the morning
Not sure what you mean
czcams.com/video/wGw5aDG09dQ/video.html
Detailed Vise bending for Crossbar
Just a buy a new slide
The fact that you said that tells us everything we need to know about you
these people have no clue what they are talking about, its a shame this is what youtube has come to.... make sure you move all of your content over to rumble like everyone else is doing.
I trust you like the video