2018 Honda Accord Passenger Side Mirror Replacement
Vložit
- čas přidán 15. 03. 2021
- The video shows the steps necessary to replace the mirror within a 5 minute period. My mirror wasn't a heated one so the replacement was a little easier to do.
Part # replaced was 76203-TVA-A01 (Mirror Sub Assy Right)
As someone who knows next to nothing about cars, thank you. I was able to fix this problem (my glass was gone, the white plate was still in the housing) on my driver's side because of your video, and your inclusion of the part name (I just changed it to left obviously because it was my driver side). I didnt have any of the stuff you did, so I used a paper clip I straightened out to pop the fasteners odd the old one, and I took a scrap of paper towel and wrapped it around the ties of them when I was pushing them back in with just my fingers because I couldn't get enough grip for the force needed without (and didn't have pliers as you used). It was about a five minute job. God knows hoe much Honda would have charged to fix it for me. Thank you so much.
thanks for the video Dale! Super helpful, when I first pulled my side mirror off after breaking it the white piece stayed attached to the mirror assembly and I wasn't sure how to proceed but this cleared things up! The heated ones are pretty much the same thing just with two little terminals you have to pull off.
I got side swiped JUST enough to spin my housing around and take my glass off.... white piece still in place, so same. Wasn't sure what to do.
Thanks , pretty much what I needed to do, the tips on the plugs were helpful!
I found the mirror glass but not the back plastic back part.
I did this on mine today and the two fasteners don't seem to be pushed in far enough even though the ball joint is in. I really think the white plastic and fasteners and ball need to installed first so those two fasteners can be pushed in better. Then the mirror can be pushed into the white plastic clips. If just the ball joint is connected then the mirror does not articulate from the door control.
I’m having this same problem it won’t adjust the mirror correctly anymore
where can i find these little while fastners thing? i lost whole glass and i am not able to find it anywhere online.
Check at the Honda dealer or junk yard.
Where can i find those 2 white socket screws?
I have the same question, did you find it?
How do I install the heated wiring? Any idea? I searched the internet, you have the best video. But as you stated, you don’t have the heated glass.
If you are replacing the glass that already has heated mirrors the two wires should be behind the mirror just hooked them up to your new mirror, if you're trying to add heated mirrors to the car that didn't have heated mirrors originally that would be a lot more difficult to do and I would suggest not doing that
Where can I get those 2 white clips wife hit something and they gone
Call the Honda dealership parts department
were you able to find it?
They only sell the whole assembly I didn’t do thst
The pieces you put on the other mirror what are the actual names to those
Try calling the Honda dealer parts department to get the official name.
were you able to find it?
@@dalechalkey3729 Honda doesn’t sell them. You have to buy the whole assembly to get it. Which sucks
Try getting it at a junk yard
Where could I buy the mirror?
Check with your local Honda parts department at the dealership
Where do you get the plastic screw and rubber covers from?
were you able to find it?
Hey @@ARafael1555 we’re you able to find those screws? I’m looking for them too
@@LuisLopez-ee6yo no. Went to the junk yard and bought the whole piece with the screw. With everything ran me up $45
@@ARafael1555 ok did you replace the whole part? Or did you just popped in the screws?
@@LuisLopez-ee6yo whole thing mirror and screw
You skipped all the most difficult parts, namely how to get the 2 white studs out and back into the sockets.
I didn't have an extra person to film my activities so I couldn't capture those parts, just talk about what to think about.
He put the small metal tool into the cut out. It wasn't easy force wise, but I knew what to do from this video, just fine. I used a paper clip. As for popping them back in, he said you had to line up the little nipple with the cut out. What else did you want? Yes, again, hard. I did wrap a tiny piece of paper towel around the ties on the fasteners when I was trying to get the ball of each popped back in, because pushing straight down with my fingers directly on the ties was hurting my fingers, since I didn't have pliers, but I knew 100% how to do it from this video. I'm not someone who knows the first thing about cars. I call AAA to put on my donut etc, and I managed to replace my mirror in about five minutes this morning after watching this video once four days ago...