Video

Buena descripción de las herramientas,gracias.

This is a great video! Really appreciate the explanation and step by step, very thorough and complete.

Love your videos.im about to redue my bathroom and have learned so much from you.

I live in the metro area and I'm about to repair my shower pan. I'm so glad I found your videos. They are very explanatory and easy to follow.

Can i skip the mesh layer and just put the waterproof membrane on top of the dried mortar bed? It would be difficult for me to get the fiberglass mesh

Love your process. I will be watching more of your videos!! Thanks!

Really nice how to videos! Where are you based out of @simonproatl ?

Since we have the pre slope and the actual slope which leads to thicker concrete install on the base of the shower, my question is that how tall the step at the door will be good enough to prevent water running out?

I am talking the heigh/thickness of the concrete at the drain

hi all, can anyone tell me how thick of the concrete do we need to install after we lay down the liner? or how thick of the concrete do we need to install before and after the liner? Appreciate

I wanted to see how you do the walls. Do they touch the floor of the shower pan?

Simon why arent you measuring how much water is needed for 50lb ?

Good video! Thank you

Thanks for showing us the simple basics without making it seem more complicated than it actually is.

Is there any liquid fails that works?

I suspect my shower drain has no U trap below it becuase it constantly smells. It goes up through concrete slab like this. What can I do about it?

Nice information and video. What model and brand laser are you using.

Ok I think I did this wrong 😭. My basement shower was stubbed in. I poured the mortar already and thought I was supposed to cut the drain pipe and fit the drain fitting after the mortar dried. What do I do now?!

Would this OATEY pan liner and glue be AQUARIUM SAFE ? can i make an aquarium seal out of these materials seen here ?

How do you make a curbless shower on a concrete slab

Excellent video, help me a lot thanks, 👍👍

Last shower i did, i did not use any rubber liner. I built my curb (wood, cement board, then thinset and mesh to fill out, smooth and make uniform) and preslope. After which i coated the curb and pan with Red guard 3 times (same thing as aqua defense except Red) After that i put my final slope, coated everything in RG again and then tiled over that. Hopefully that made sense. This was all done over a concrete slab.

ur the best @simonproatl , quick question, what if i want to install a shower door on the curb would i still angle everything towards the pan? or would i want the curb to be flat and level?

Thanks for the great video! My 2inch ABS riser coming through the concrete floor is not perfectly vertical. A typical ABS welded connection to that pipe would end up with an 1/8 inch deflection from horizontal at the drain surface :( ..is there a solution other than jack hammering there entire area to replace the U trap and riser?

THANK YOU for making this video, it’s so helpful and specific for my project.

keep them coming.... so anyone of these mixed bags will work, theres no better one? I see in all your videos you use the Sakrete 50 lb. Floor Mud Mortar, but home depot is out of stock everywhere in my area, but they have the sand topping mix, are they equally the same or should I look for the sakrete one instead? maybe lowes has it?

homedepot is out of stock for the SAKRETE 50 lb. Floor Mud Mortar, which other one do you recommend? I like your videos, I am about to do your concrete curb this week, next is the pre slope bed... just dont know which mix to use... thanks!

great videos Simon! question about this one but are we not putting screws into the concrete after it sets or are we just relying on the concrete to hold the drain flat/level after? Just cause in the video the 4 bolts you have are for the pan liner i guess and the other 4 holes would be to screw into a wood subfloor? are we just ignoring the extra holes using this method?

Looks like you applied the thinset over the waterproofing membrane before it dried then painted another coat of waterproofing membrane over the thinset before it dried. It would seem that once the outer layer dries it will encapsulate the wet thinset and never fully harden. What do you think.

🎉ty.god bless

Tile down to floor from side of curb seems to be no joint allowed

Can you use the same drain over concrete floor?

That's pressure treated wood??

Maestro

Respect for your professional work very well detailed and explained you just got a new follower I do this type of work myself I know you are a Master

Thanks buddy. I know these take some work to put together, but you're helping people out

Hi. Do you have to put a pre-slope below the dry pack? I was planning to do a dry pack pan thats sloped to a flo fx drain kit. Its going on a slab. Can i just do a sloped dry pack pan, then use the waterproof membrane, then tile? Thank you for making great video.

You're doing amazing Tile work. Waterproofing is definitely your expertise.

I need you to come in my area in Orlando Florida and do a full bath. I'll pay for your hotel stay

Your video is great content, i like it. I have question though. How long does it take the dry pack to set before i can continue working? Thank you.

Great step by step diyers. Thank you.

👍👍 aprobado

You make that look real easy my friend. We will be installing a walk in shower soon and you taught me alot here. Thank you for taking the time to make this video. It look great.

Good tip for mix with 2 buckets thanks🎉

Thank you! This helped me out! I didn’t want to do a counter sink floor like another video showed.

Nice work!

0:29 Why not show how the floor/subfloor/base is constructed? How do I get to this point?

Great video, but I would like to know all the steps from the very begging to the end. Thanks a lot!

Can i use fiberglass cloth instead

If I mixed mine a little dry unknowingly can I just mist the shower pan to wet it?