Video

I'm using a universal plier. You can use the same or buy/borrow Adam's plier from your ortho PG I'm using API

@@dentocare14Thank you so much 😊

So basically it is done to prevent displacement of the tooth

You can do 100 times better than this, I'm pretty sure

You can but you have to manage the pressure as well and as books suggest there are two types of curing and also take care about the time but yes it is possible

Ok thank you

Then it won't be separate and i guess it won't come out of the cast.

Then what i have to do sir ?

Thank you so much. Do share with friends and colleagues

Thank you so much. Do share with friends and colleagues

Thank you so much for your appreciation

Yes but also you need to go with conventional preparation with amalgam restoration to get better retention

Okay that's an interesting question. Yes you can carve it without adding extra wax, it's optional if you have enough wax to carve then no need to add extra wax. Also to shine your rim/carving heat the wax very gentle and very little and immediately put it in the water then you will see the magic

@@dentocare14 omg thankyou so much for replying this fast cuz I have my exams tomorrow... Tysm again💗

All the best and trust your knowledge

Thank you so much. Stay connected and do share with friends and colleagues

Thank you

Which video do you want to see next?

@@dentocare14 Triangle Rectangle Circle Square U V Shape All basic exercises

Simple remove the pin if possible and hit it with something hard on the top and it will be remove easily

You can buy spirit at any dental store or online easily

Please watch first video on this channel

I know and see with time things changes This was one of my initial works

@@dentocare14 ohhkk

@HyperCity-ed7em and i truly believe and want everyone watching my videos should do better work than me

@@dentocare14 yes did way better wax up than this in my first try actually

Just follow the textbook and try to place it buccally Use carver or wax spoon and push it towards the rims

@@dentocare14 sure sir ,thank you ....I followed ur steps and placed every single tooth perfectly .I have only problm with first premolar. Will try to place it buccally . Very grateful thank you sir 🙏🏾

Yes definitely

From where it is broken like can you share the landmark

@@dentocare14 both side of retromolar pad

Firstly we can't do anything and secondly posterior to retromolar pad often breaks during the procedure

Firstly we can't do anything and secondly posterior to retromolar pad often breaks during the procedure

You can get these from your nearby dental store if in college or nearby or if you want to order it online you can check dentalkart dentalavenue and some other websites

Keep it in a warm water and then remove the it slowly .

See you don't need extra wax everytime, you can carve out without using extra wax but make sure there is enough wax already when you make the occlusion rims

You can simply trim it but it's time consuming process.

@@dentocare14 it's not getting thin I tried

See if you made it with dough method it will be hard to trim tbh, either make another one or use carbide bur to trim it

How to clean the base plate from inside

Please check the anatomy of both the teeth and if still you have any questions, feel free to contact

So the thing is you should have read about the stages of heat cure if not putting it in the water for curing it will change the stage and problem will start. So better to put the denture base in the water for curing as soon as possible

Todo gracias a ti por ver el vídeo. comparte con colegas

You all are for watching the videos

Pick it up clean the tooth thoroughly remove all the wax and put it back in the place

See it depends on the case you can't have ideal case But in preclinical both are important but read about it first from any prosthodontics book be it S. Laxmi, Deepak Nallaswamy or Rangarajan

Have you relieved the frenums?

Will relieve a bit again and see what happens thank you

Okay, that's a very normal thing that happens So there can be multiple reasons for this but one thing is shrinkage as happens with cold cure. When you make a base plate and removes it from the cast immediately after fabricating it, it tends to shrink Better if you remove it from cast then place it again on the cast for sometime or else place it in normal water and it won't shrink So next time do this thing and get back to me and comment if it gets adapted or not