Video

Had this fault just after an oil change , garage took new filter out and back in and it's fine now

What size drill bit did you use to make the holes? Excellent video btw

Very helpful 👌

Are these coded to the car or just plug and play ? Cheers good info in video

Thanks for this!

Will try this to my T25 too. Thank you! Inspection coming and i think too much slack on that. Now I don't need to visit mechanics for this kind of job that is easily done by myself.

Does the door open as it should ??? you didn't show that part

Brilliant video - just bought one of these canopies and this is really helpful learning how to fit it properly. I didn’t even know anything about the special fixing screws so this really helped me get my head around that and the template idea is so helpful as I have a 2m canopy to fit so your method will make it much easier and will get it up perfectly fitted. Thank ever so much.

Indian scam

why didnt you show putting on the boot cover?

Great video, at the start when you are ajusting the brake shoes at the wheel is the handbrake inside down ( off) ? thanks

No hassel. just straight on. That's how we like it. Thanks!!

Hello friend, i have the same issue, the front wheel dont break, but dont have error lights abs on the panel. Its possible? Obrigado

Wait so I just bought a breaker bar when I could have just jacked up the car and turned a wheel by hand... That's a great tip.

Best template ever…

Great video .. very specific love ir

It will be very help full if you have add the drill bit size you use to make the holes

No washer on the top

Ford fiesras mk6 lower bull joint ca. I do it ?

Good job. A bargain too

What is the size of the drill bit yo use? How deep do you drill holes?

Thx for posting, gave me confidence to do it myself. You didnt mention you had a cup of tea around to help think things through ! :-) . Maybe add how it fared through the winter ? I want one to stop me getting dripped on as I unlock the front door, so maybe I'll find one with a lip on the front edge to direct water off to the side.

Fan is working at 4 speed but heating is poor

Useless video. We'd like to have seen exactly how to remove securing o ring and especially seeing it getting fitted. I'm now away to find a video that shows this being done.

Realy nice work! Is this this the 1.4 petrol engine

What tool was used to remove the 4 star patterned bolts?

Thank you very much. Very clear

Spot on video 👍

You did well. I can not screw into the holes and did not grip into the wall. How can I fix it?

Where can I find this on a 2011 Punto Abarth Evo? Looked everywhere, I guess

do you have to bleed the breaks in order for it to work? I know it’s been 4 years but maybe someone knows?

Damn, looks more expensive than I'd hoped, but thanks for posting this informative video, really grateful

So dealer said on my repair sheet for 2014 honda accord ( both front lower ball joint boot splits ) so what acutal part do i need

How does it hold up with the weight on snow on it?

You said start bleeding from the wheel farthest from master cylinder. I think its not correct should start with the wheel fartest from abs pump

i would love a link to a suitable one for my vauxhall astra!

6 yrs on did it solve the problem long term?

Can also use masking tape instead of wood. I've always used this method for hanging picture frames.

so i have this problem every 4k, pulled vaccumme off and clean but constanty block up metal filer on vaccume pump, pulled sump and cleaned pick up and again 4k down the road same problem, any ideas?

You should watch a video about how to make a good video 😂

Do you need to put a new gasket when removed it?

Brilliant video. My daughters corsa is having breaking issues where only the drivers side front brake is working. Sounds like the abs pump to me. I'll remove it and test it as you've described. Many thanks.

People , good video, warning if u use thinner gear oil in there, it may come out the seals, its like water,... use 85/90 , not low viscosity....

I've solved this problem, first channel on the abs pump, more correctly valve, was stuck in closed position, front left wheel didn't brake. I heated the pump on oil radiator 😅 for an hour, sprayed valve opening with wd40, generously, and hit it with a hammer more than couple of times 😬 on that corner close to jamed valve, after that valve was unstuck and I was able to bleed the system, flow was restored and it's braking again. Also I used some hose from garage to blow air, with my lungs, in oil supply opening, there is two, air must go trough all four openings. You can try it without any fancy tools.

Can this be a cause any squeaking??

Brilliant idea with the wood template. I'm gonna do that right away in the middle of installing an eighty inch wide thanks for the tip Mate !

car starts to acting strangelly or braking bad with this problem

Is anyone active yet? I got problem, when drive and torque got some value sometime at 900, sometime at 1500 got flashing oil preasure too low. When hit the gass pedal it disapear and again happen on some time...

Any idea where to get the new O rings from? I am deep in googling RN. Thanks

Good job.👍👍