Video

For Pete's sake get with the times ,,and stop wasting time and effort. Put a dye pack in and Wala, uv dye leak check , 100 % success rate 😮 And no it does not damage any parts. I know I'm the owner.

Thanks for video

I want to need trening Course about chiller, please support me

I’ve seen everything from small one ton units to 1000 ton package units and you know what? Some are more complicated but the physics is the same. So don’t let larger units scare you (within reason).

Outdoor air quality sensor! The shit they put on equipment these days. So what, if the smog is heavy, it shuts off the unit?

Meat juice ice cream AND popsicle is crazy nasty 😊

😊BTW what's the parts # for the coupler

If you are posting videos to CZcams about chillers etc I would hope that you know what you're doing. If people find this content interesting I should start my own CZcams channel. Lol All these channels are getting ridiculous.

Good 👍 job

❤

Thanks man!! Currently working on the exact gear box. Helped alot.😊

I enjoyed this video! I liked that you aren’t a “know it all” you worked through the steps and it was very nice seeing you figure it out. Good work bro

What brand was the white unit on the other part of the roof

It looks to me like that is a 2-stage vacuum pump. There are 2 pumping rotors with vanes, each one in a separate compartment. The exhaust from one compartment is the intake for the second compartment. That’s also why there are 2 reed valves. It looks like 1 of the rotors is thicker than the other. I don’t know sure which comes first? I recently bought a similar 2-stage vacuum pump at Harbor Freight. Everyday price was $139 but they gave me some discounts so it wound up costing < $100 and it works great.

nice job

You the man,

Ninety percent of the time the leak leaves an oil mark... the problem is that annoying 10% in which it will leave an oil stain after years of refilling and the machine makes us look useless and some once I thought I heard her laughing at me

Txs, i was affraid to replace one of those, now seing you, i feel confidente to do it at my hotel.

Question why are you using a CPS micron meter? Do those Testo gauges not have a built in micron meter?

That also looks the wrong economizer kit for that setup, there are two different economizers for Vertical and Horizontal. I think you need the Vertical economizer for this setup.

I bitcoin for u 😅😅😅 great job

Judging by the dirtiness of those fryers I’m going to guess jack in the box

Hey man, I'm just glad to see youi tear it down, I have one that runs but is not sucking a vacuum and now I know what to do. Thanks.

Probably another company stealing refrigerant from that unit

Glorious beard

Nice job, I have this same problem and as soon as i started to look into the smoke detector it started raining so I didn’t get to finish. I thought i was crazy too because the board had power but wasn’t flashing any lights.

Did you check if there was a siphon in the drain ? If no siphon it might suck outside air in to the evaporator.

Hey where is the defrost term sensor located? Had case frozen over washed out allowed case to reach set point forced defrost heaters come in and out every five minutes term temp not reached!

Any videos on ever changing those bushings ?

Serious question sounds little dumb but left me puzzled for years. Lol If I have 213 incoming volts should I leave transformer at 240v or should I change it to 208 v. The voltage is closer to 208 but voltage is over. I would love to hear your thoughts on the matter. Thanks

Thats a loooong down time in my area..

I run into this issue a lot on these cases. I spoke with zero zone tech support and the guy told me it's because of the drip time not being long enough. And that an additional heater is not needed. What do you think about that?

I relay enjoy your programs

No fun doing this stuff

Our makeup air stop making the usual noise it’s kind of quiet and sitting could it be that it’s not working ? We haven’t heard any complain so far .. Should there be a concern ?

Looks more like four defrost, not three

We did a helicopter lift of 14 of those. Covid units. Had many blower bearings fail right away. One blower wheel blew apart. The warranty blower replacement was fun. Comes in pieces. Gooooood Times!

Yes, definitely learnt something--you sometimes have to troubleshoot the guys who came before. Thanks for sharing.

Why they don't make a discharge port with hose connection, So you can use it to test system pressure?

Can some one explain, why there is a reading in x and n. If the circuit is open. But then there is no reading when the circuit closes? Thats the one part that i dont understand. Other than that, really helpful video thanks

chrome socket on the impact is crazy. is that a 2D?

I know it had been 3y but your videos are always very well explained and professional

Have you came across a code on a Greenheck with a 4-1 code purge cord problem?

hope u have correct diagnois

Thank you very much, I am a new tech and never replaced a Henny Penny pump, your video was very helpful, God bless you and your work. You help people and make a difference

Thx Bill for sharpening my skills. Cheers 🍻

Why did they use LG compressors !!

Do you remember or did you ever find out what the pilot has pressure is supposed to be?

I appreciate the video because I'm working on the same piece of shit with the same issue.

If you look at the whole data tag you can easily tell it’s not a 4 ton, 5 ton, or 6 ton unit. Right above the two bar codes and below the Intertek logo it says “Cooling Capacity 88000”. So that makes it a 7.5 ton unit. Pause the video at 0:27 and you can plainly see it.