Video

My car has 47k miles, no problems at all. Just installed catch can, thinking to change the pcv just in case

I’ve been on this earth for 60 years and I fix all my vehicles over my lifetime and it’s never ever been the spark plug. Although we wish it was it never is.

I followed you step by step and disassembled my 6.0 LS . This was my 1st time disassembling a LS motor and your video was perfect. I even went to the store and rented the same pulley. Thank you for the upload.

Where did you get your black hardware? And did you sand and prime before painting them white?

Have you noticed every time you unlock the truck the reverse lights turn on?

What year is it

I know this is an old video I’m also building a 5.3 but for my LS swap gbody MCSS but I do own a 03 cate eye Z71 I’m thinking about building later, anyways that smile on your face when you was getting back out of the truck after first start up says it all it was priceless love it dude keep up the hard work it does pay off at the end

Why you replaced the crossflow cooler with the low efficent thru flow cooler?

Don't worry about how loose the tie rod nuts are. They don't need a ton of torque because they're under insignificant load. All they do is push and pull the knuckle in and out to steer your car, which doesn't take much effort when it's moving

Pull a plug and look!

I've never seen a bearing come off so ridiculously easy. It usually takes an act of God to beat or press one of these off. Use some never seize on the flange and race when putting the new one on for the next guy. And maybe it'll come off without an hour of beating.

Which year is your truck?

Sweet video bro, looking forward to doing it on mine this weekend

You have links for the steering wheel and buttons?

Why is the tie rods upside down ?

Awesome video! I need this done on my GMC Sierra 1500

bro i’m the guy who just raced you omg that shit is fast asf

Have you installed the inlet yet?

“Like and Subscribe” 😅

What was the problem?

i have airbag light on now

Why would the coating be good on the outside when the inside carries the heat?

Mitch… I think you did an awesome 👏🏾 job recording and working at the same time on your vehicle, very detailed and informative you were plus the outcome was impressive guy !!

Where did you order the fender flares?

Does crayoned come in bigger bottles than 4oz

U find better gasket that works with these?

Don't have to pull head to change lifter fyi

Collapsed lifter

It's cyl 1 or 3 and those rockers ate just loose yeah

What do you mean by base tune? Is it one specific for the cam or just a base tune from a plug in play tuner? Trying to figure out what to do before installing my truck norrise cam (i have no local dynos) but i do have the diablo trinity platinum and can except custom tunes.

I’ve got an expensive set of heads I’ve had for yrs but have been held up due to injuries but refuse to pay the prices tat they charge or to let them rust and believe I’m going to go this route also and use multiple coats with curing time in between but I’m watching yours,good luck

Mine runs perfect without the breather.. I even got a little increase in gas mileage and performance

Good vid did the engine run better and better performance ?

Just pulled a set of these off my parts truck. Got them installed on my truck and the turn signals work, but the yellow lights don't come on with the park lights. I've seen other videos where you have to wire a separate wire to the park lights fuse as well, but mine only has two wires like this video. Do your turn signals come on with the park lights? Wondering if I need to put in my own third wire, or if something on mine just isn't working right

Since the crank pulley is now smaller, did it affect the voltage that the alternator gives out when idle?

7 months late but really appreciate this video!

up north we call em chimp lips

how do you pass emissions without cats? i want to put them on but want to pass emissions too.

So what if my truck is so rusted to shit that there aren't holes to line it up with

I have a 2014 535 I & just noticed I have oil in the coolant😮

I salute you for the solutions and I like to thank you.

B a good idea to check your cam bearings if there’s that much scarring

after watching this im so glad i bought corsa extreme. i hate the borla sound.

Nice sound

Nailed it bro, no BS CZcams personality crap, just meat and potatoes, nice work.

What size is this? 90 gallon?

Fuel pump

2 in headers?

Could I just use a microfiber towel for the wax and grease remover?

Thanks bro made this possible