Video

I have my rotors and pads sitting on my shop table... i Halen to have a day off today... and was about to waste my day doing nothing... but this video gave me the motivation to tackle this job. 👍

great video .thanks for posting

FYI, real easy to gain access to the back of the wire harness in order to plug it back in. Just take off the glove box, two screws at the bottom. I had to unplug it at the harness because the red wire came loose and had to solder it back on. The light on the driver side is easy to reach from under the dash so I took that one off too so I could clean it easier. Thanks for the tips on this and some of your other videos.

Thank you for such great videos! I just bought my Miata and it’s been very informative watching your videos! Years later and these videos are still teaching 🎉

good video and good bloopers

What size 180° silicone hose would you recommend? I’d like to buy one, and make as little cuts as possible, to use as little connectors as possible. Thanks

If you cleaning da overflow revoir you can put rice or sand in it and shake it up it scours the inside debris away but make sure to get it all out. I could not see coolant level before doing this now I can.

Thank you for the clear and concise video

since i have an a/c pully as well would anything change?

Where did you get the new calliper from please? Genuine or aftermarket?

I damaged one of my rear calipers like an idiot by using a C clamp and not knowing about that hidden allen key gear... So now I have to watch this video. It was great, thank you!

Hello MiataMods, Can you make a video about fixing the A/C in an NA or converting it to R134a? I would really appreciate it

My caliper doesnt move upwards after following the Steps

Great video! I just picked up my first '94 Miata with 36K on it. Oil change if first on the list.

7 jaar later, zelfde probleem, zelfde kleur spiegels besteld🫡😂

btw if anyone is looking into buying this now they changed the design so that the cable don’t need to be cut anymore

Is this automatic gearbox?

Tiny garage but I love how organized it is. Tall guys, small Miatas.

I got good improvement by cleaning switch contacts and putting reflective foil inside the lamp housing but did not change to LEDs. I'm a real cheap ass.

very good thank you

How diffrent is it for the 1.8

Great video! I need to install my frame rails asap

Watching this video gave me rage fits. Why do they have to make stuff so stupid

Really good video!!! Thanks!

Very hot water works better than a lighter. ✌️

Gonna take a crack at it tmrw. Very helpful video!

When you said you if you don't have a copper washer nd that you have a whole collection I expected you to share them

That looked like a crush washer...

Do I really have to drain all the coolant or can I just take off the top radiator hose and wing it?

Great video! I’ve done brakes once before and this was a great to refer to. Very informative and the camera angles are great. Thank you.

Just did a flush today, with this videos help! Also, the thermostat video was very helpful. I ended up boiling the thermostat just to make sure that wasn't the issue, since mine was overheating. But a thermostat gasket, and a flush later was all I needed. Thanks!

Hoping this fixes my P0300 misfire error on my 230km ‘97 NA

I had that same model of aluminium caps and got stuck even i putty ceramic pastes onto stems 🤦‍♂️I had to grind caps with Dremel all the way to the threads. Duckt tape on pillars and 12 mm wrench got them off😂😂😂

But the front wheels are up in the air, you aren't going to get all of it out.

Hey man love your videos and how at home friendly they are!! Do you know of any issues with messing with the air fuel ration by adding the filter and the kinks in tubing?

Do you like the head unit you have!

simple and easy to follow

awesome

When doing this is the E brake pulled? Or is in the resting position? Might have missed this part lol

Hello... I drive an MX 5 NA Miata 1.8L (only when the weather is nice), now 30 years old and has done 160,000 km. What kind of engine oil would you recommend? Thanks, Hardy

This is a COOOOOOOOOL video. Quick tip, always keep the rad cap loose on the radiator (when doing the job) so nothing falls into it by accident, that can also be done for the oil cap when doing oil changes. Same principal applys for simular jobs. If not the cap, then just put something over the holes to be safe, like a towel. Don't forget to bring a towel. 😂

You ever find sometimes the oil cap can be a P.I.T.A to unscrew? Just apply some grease or oil to the threads before turning it back on and it will be user friendly next time you want to undo it if you are low on oil or doing the next change. I like how you wore gloves for the whole thing being careful except actually applying new oil to the filters gasket with your bare finger, that made me chuckle some.

Its so satisfying hearing the engine get throaty being able to breathe more air. It never gets old. But we do need to take care of our own bodies and stop polluting the air as we can keep breathing deep throaty breathes. Not like darth vader but you know what I mean. Most of you anyways.

Man I went to the hardware stores today to try and build this but it’s gotten to the point that it’s cheaper to buy a metal one off of Amazon than to build my own. What a shame. But thanks for the video!

What if I don’t have access to or heat bc I did a delete

This helped me more than you know, was watching your guide for pads and disks, came across my rear calipers were seized, and here we go, you have a guide for that too! A tip for any NB facelift owners though, the brake caliper holder (with the slide pin) will interfere with the brake disk, so you will have to remove it - the top bolt can also be obscured by the ABS sensor, so use a long box wrench, or remove the sensor bracket (1 bolt on top)

2024 and this was the best video... subbed

Reminder to California residents. Evap canisters are required for inspection.(I’m getting a smog and found out the hard way after following this tutorial a year ago).

I bought this kit and installed it. 2 weeks after install the lens covering the bulb fell out. A week later the light stopped working. JASS products are NOT to be trusted.

I think the original location is the worst place to put your license plate on a miata. Looks like a pornstache. Glad u fixed it! Looking great