Video

What does the button below the ignition switch do mine just has a hole in it

If you could do 10x less talking this video would be great

Best video yet on this process. Thanks

I have the original wiring, where did you connect the constant power wire to?

I got a 5 speed and I want a 3 onna tree so bad if I wasn’t so reliant for transportation for my job I’d get one but seriously thinking about gettint one as a second vehicle and just deal with paying insurance on 2 cars

Impossible to find a video with torque specs

What years the truck

A lot of vids dont show these small of details such as the addition of speed clips etc . My new dash actually started sticking out a little on the drivers side to where it started to touch the door when closed. I now know i need to put a clip and screw on it. I like your gauges too. Thanks for making this video.

Great videos. Sad it's only 360p, but still able to see what is going on.

For my 2015 chevy Silverado 2500HD the part # is PL8140 from Amazon. Also I've found 4 brown and yellow wires in that bundle, the right one is the thicker one. There are also 2-3 gray wires as well, the correct one I've found it on the bottom of that bundle towards the center of the truck. Connect the green to the brown/yellow and blue to gray (I've solder my wires)

Do it right the first time

You inspired me to build my bike, great job

can you lmk where you purchased those peaces please

Love the videos, but I have questions, did the lower control arm adjustment move at all due to loosening? you tighten the low control bolts with no jack under the lower control arm? removing the top hat effect the alignment? Should you mark the lower bolts and adjuster before starting this job. and last, if done like you show will the alignment be the same as it was before? Thank in advance for your answer.

Where did you get the capacitor?

Si el flotador se pega y se vacía la Cuba de gasolina y la aguja no tranca que pasa allí

Napa store brand new $67.99 lifetime warranty

Firt tink clean or put w40 I did in my chevy 👌🏻

Thanks

Awesome video. Very helpful. Plan on putting buckets in my stepside and this definitely will help out!

The pin goes down like it's supposed to, but it won't slide out like it's stuck

Good job sir!!! Thanks for the stroll down memory lane. Dang!!! Miss these days.

Clean AF👍👏👍

thanks this is exactly what i needed my 2014 CHEVY has been what i thought burning oil but now i believe this will solve the problem !!!!

Your steering wheel is upside down

Vou operar meu opala

Meu opala será operado kkk

Do you happen to have the product number for those isolators ?

What's that piece connected to the lock cylinder that connects to the locking rod?

My border collie used to do this, we used to have great fun with a torch at night 😂

The relo bracket was installed wrong

😎👍😎 .

Thank you for the video

I’m getting ready to buy a ranchero, and it’s a three on the tree. I drive a mustang with a manual transmission. Thank you for your video, it was definitely helpful

What does the green wire for the passenger turn signal get hooked up too?

Wats the two bolts size at the bottom

My Tesla would smoke this hunk of junk 😂

How low do these sit?

Un gusto saludarlo, tengo una chevy 1987 con este interruptor pero cuando doy giro a la izquierda para que encienda la luz del techo a veces enciende en otras no, a que se deberá eso?

Nice video sir thank you! I was wonder if a 3 speed is fast?

Since your truck was a manual clutch pedal assembly with the clutch linkage when you pushed in the clutch do they pick up the front of the cab

Anyone else have a parent that made this seem like the hardest thing to drive it's just like a standard transmission but on the column

I thought you video would be informative but listening to your dogs bark no way!!

FYI I’ve watched your vids for years to help figure out how to do various fixes. Idk if you’re still working on these but I sure hope so and miss your content. Thank you

Hey bud I was looking for a video on how to fix the cab bracing? I have a 1978 square body and both front cross bracing is rusted just wanted some extra help. Thanks

What size rims and tires?and where can I order those tires?

I would like to see a ac wiring video

NOT a rat rod. A work in process perhaps?

I saw the drop blocks at the end but weren’t there in the beginning of the video. Did you remove them ? And did that help with giving it more lift meaning not going down as low ? Thanks

On that corner male connector how about simply trimming off some of the plastic with a razor ? It didn't look like much was needed to clip on right , worst case scenario , if you can't find the right connector.