Video

Check fuel pressure sensor?

I autocross an Integra Type-R and one of these came up for sale. We're thinking about getting it now I want it more for autocross🤣🔥

Didn't like the fact that the video wasn't more under the hood and we could actually watch the job being done step by step instead of saying more of what was being done. Camera man was not close to the details which helped it come off as a lazy demonstration more of hurrying up to get it done less of look at what I'm doing so it helps you more to learn.

Hello friendo, im have a trans am 1994 automatic , and my code obd1 is a 18 what problem is??

I think my navara the torque settings for the wheel bearing were 40 lbft. I cranked them snug then a half turn each.

What is the buzzing noise or compressor noise when you turned the key back on after the fix

What does the orange wire do , what is the orange white wire used for ?

Thanks my 2006 blower motor is out this helped immensely.

THANK YOU SIR!!!!!!

Had 6 firebird's....My least favorite engine is the LT1....can't beat a 400.

What did you use to reseal it?

Brilliant walk through of how to do this. Unravels the puzzle very well and would be nigh on impossible without this information. Awesome work.

I just installed the same headlights. Luv them. Same Nissan. New paint job as well. However I have a problem. The turn signals only work normally when the headlights are not on. When the headlights are on, the turn signals front (& rear) start blinking very fast and the L.E.D does not complete the entire loop. Fun install, but trying to trouble shoot that issue.

Awesome Biff!

Hey biff love the Chanel, but I have A 94 formula with the 5.7 lt1 and I have the same identical codes all 8 what I was wondering is did you find the problem that was causing the problem. Thanks Ron

This video was a quick fix to solve my problem in about 15 minutes thanks alot!

I cannot thank you enough! I also own a 1994 and yes it is disheartening that noone reproduces these taillights. I need a set desperately bad, BUT, fact is all of them do the same thing, so why spend $650 on them when your lucky to get a good year out of them. I most certainly will be doing this! Thank you so much for taking the time to do this video and help all of us out so very much!

What is the tightening torque for the bolts of the pan itself. I have changed the new pan/gasket, but it's leaking. Thanks.

Change 2 see if it's Sparking

Yellow top it the way to go

Ok, so I followed this tutorial and it was very helpful cutting through the mystery of just digging into the job outright.. Direct labor time (Waiting on the wife to get the new alternator and her battery charged) this removal to full installation was about 2.45.. The wife said she was finding things that weren’t working right and quite a while started working again. Like the sports mode in the steering gotmuch much better and even her headlights which she was getting new bulbs all the time because they didn’t seem bright enough finally got a lot brighter. Never knew when a car depends this much on electronics how much that alternative plays a role into it. Great video…

So all in all, roughly how long did this job take to do? From start to finish that is?

Good video

Your a machine, took the pulley with no special tool. Nice dude i rewinded twice

Thank so so much teacher 👌🏽

How hard was it for the middle seat belt I’m stuck on that part right now any advice ?

Perfect thank you for the help

Whats your review on them so far? I really like the look but cant find many reviews on them

1992 TO 1996 CAPRICE ~~ ALSO SAME OPTISPARK

That's wrong man you suppose to use a heat gun, cheap at Harbor Freight?

You didn't show what grit you used too sand, ineed to Know? Did you sand wet or dry or Both? Say that before you start!?

I have 1995 Pontiac firebird formula that when is cold it starts right off and then after driving it for a while and the car being hot, when to start it and it would turn over but it won’t start until it gets cold again, any idea of what is causing it or any suggestions? Thanks much!

I know its an older video, but do you remember about how long it took start to finish ?

Just replaced it with new reman what ever that means and still just clicks once every time when I turn the ignition any help please and thank you

Appreciate u taking the time putting this together, I am up and running!!!!!

Thank you for the video. Now i see what must be done. Had an ABS sensor fail. Gotta change whole hub.

On measuring where your 3 tabs are you said the back, lower ones were at 1 1/8 what was the measurement for the top one?

nice video Sr, thank you!

The adhesive on my seals didn't stick, did yours work OK? I am thinking that doing this in the cold caused it

Well done, huge project, looks great

Where is a good store or website to buy the fuel rail?

@20:05 what is that part called? The last owner of my WRX got something smudged behind the glass display and want to know how to clean that out...

You should give a little Sti update on how the paint and mods have held up sometime!

My 96 doesn't look like that

Great job!!!

Knee airbag is the worst airbag on them all. Thanks for showing me my plan is to take it out.

Auto lite are trash

I just came to say THANK YOU.. I LITERALLY had the same problem.. I watched your video and was like.. it can't possibly work that easily for me.. I did it exactly the way you did and IT WORKED!!! it took a couple sprays .. and I used a screwdriver to open the plastic cover a bit to get a really good spray in there.. and within 5 minutes I had them both off.. you're a lifesaver

Did u figure it out I'm having same issues same car need help fans not kicking on

Great video. What a nightmare!