Video

Do you have for n62 engine?

Hej Martin. Ser din nye video ca. 1 år efter vi mødtes sidst til din fest. Du står stadig snorlige, og dit indre udviklingscenter snurrer stadig lystigt. Jeg holder meget af at følge dig og din fede idéer :-) Mvh. Henrik

Installed on my '17 M240i today. Took about 2 hours. Only had to loosen the heat shield and pull it out of the way a bit. Didn't have to loosen, lower, or remove anything else. This is a great product. I'll echo what someone else commented on regarding the rubber insulators adding thickness/height to the brake cable that prevented the lower part of the bracket from sitting flush against the upper part of the bracket. I made sure everything was lined up properly, ensured the seam of the rubber insulator was facing upward, and tightened the 13mm nut down good, but still could not get the gap to close between the upper and lower bracket. Not sure if it's completely necessary. I'd think as long as the nut is tight, should be fine, and definitely more secure than the OEM part. Maybe the brake cables are a tad thicker on an M240 compared to the car in the video?

Does this tool realy work on s63 also?

Yahtzee!!

What is the reason that makes it break??

The blue tool box tour video!?

What BWM doesnt have massive oil leaks. Like they want it to just to give you more reasons to visit the Service Dept. Always great to see AGA one step ahead of BMWs engineers

is it possible to repair this issue on a 4-post Lift without removing the Engine/Powertrain?

Can you do e93

Is it also available for 2011 e350/a207 models?

I must be doing something very wrong because I can't get this tool to install the keepers to save my life. The keepers never seat but end up every which way and i end up spending enormous amounts of time looking for keepers.

All the AGA tools are so much expensive it's like scam. Aga tools not worth it

Please tell me why this should not be mandated for all new vehicles? Pure genius ... kudos ... so simple, the kind of thing that only a thinking person, spending a lot of time under a hood could invent. Like Edison said: 99% persperation, 1% inspiration. Watch out filter, you're next!

Would this tool work for the 991 PDK?

Just done this, removing a solid mount on my 996. Mine had the chamfer on the transmission mount hole on opposite side to what is shown. Always install new mount into the side of the transmission with the chamfer. it allows the mount to install easier

big thank you . just subscribed !

Is this only for dealers? Or do you guys work with independents as well? Does your software integrate with any shop management programs like Tekmetric?

it's the little things that over engineered German engines always mess up on

Amazing 🎉

Will be ordering mine today ! Dealer was trying to charge me $950, which is absurd & they kept pressuring me to change it.

Wow, didn't even have to remove the camshaft or timing chain like what I see in other videos

Wow nice product 😮 the first seen for me shipping to Germany?

Excellent quality service

How much is it ? Does it cost include the van or you bring your own van then you guys just install it ..

Nice to hear that imminent progress is being made on the non-Pro Version for a Drain Hose attachment. I intend to use an Oil Extractor from the AGA Plug. Thanks guys!!

Love the air line and pwr in the cieling.

I’m asking for this for my birthday. 😬

should add 2018 M240 has 2 more brackets to the cross mount require T60. the old plastic slid right off, no pliers needed, after soaking with silicon lube and sit for 30min great fix, easy install

Thank you for doing this video! The steps outlined made the install that much easier. The dealership wanted $1200 to replace the bracket with the same piece that was just going to break again. I just finished putting in your bracket and what a world of difference! No more noise and I’m confident I’ll never need to replace that part again. Well done and thank you! 2017 330i

Good 👍🏼

How much is this? Didn't see it on the website.

Here is a tip, Use a hook shaped pick to get underneath the plastic part and to pull it down. Mine was stuck and the only way to get enough leverage was to use a hook pick and pull down on one side close to the rubber

Always impressed with the ingenuity of this firm with the specialty tools they have created. Well done!

I have a question about the Pentosin 11S CHF recommend by MB for the ABC system for my 2005 SL500. I've been using AMSOIL synthetics for decades in all my vehicles over the years. Best lubricants on the market IMO, however expensive. They do make hydraulic fluid for various applications. Nowhere have I ever seen MB list any AMSOIL fluids of any kind as compatible...at least for their ABC system. I assume they want you to use what they recommend. There's no warranty on my SL. What would you (or anyone) have to say in regard to using AMSOIL hydraulic fluid in the SL ABC system?

You are amazing at diy videos!! Just straight to the point, no trying to be cute or funny. You are the ideal content creator!

Awesome table! It works great for an engine stand (hemi) while you're transferring parts over.

Music?

Great video guys, and this product is well worth the money. A few tips for anybody doing this (2015 F30) - this is much easier than ordering the plastic OEM replacement, but don't kid yourself, it's still a hassle - took about 2 hrs on jack stands in a parking lot - didn't need to lower the exhaust. Just unbolt the rear heat shield and slide forward - clearance to work will be TIGHT unless you lower the driveshaft, but I got by without lowering it or the exhaust - do yourself a favor and pick up a quick 13mm ratcheting wrench, you'll thank me later - overall, $130 seems a lot for a part like this, but believe me, once you get under the car and start dealing with the pain in the rear plastic piece that's broken, you'll be glad you spent every penny

brilliant !!! not only useful for the x6 but other vehicles we work on.

THE PROBLEM IS ALL YOUR TOOLS ARE SO EXPENSIVE.

*The problem is, you have a BMW with the N63 engine* Yes, yes, that’s a BIG problem 😂😂😂 But, they pay the bills and can be brought back to life 🤷‍♂️

Sir can you help me

What about the S63? Same block right?

thank you for making this video

thank you for making the tool

Closed system good design. Looks great!

Hej Martin, Det er dælme et smart med smart på gennemtænkt system :-) :-)

What is the point ? No advantage in my eyes.

I'm looking for a shop in the LA area that has this tool and can perfrom this service on 2018 BMW 430.