AGA Jack Rod Stand
Vložit
- čas přidán 24. 08. 2024
- The AGA Jack Rod Stand is part of the new AGA Clean Oil Series. When in situations where jack stands don't work, the AGA Jack Rod Stand is the perfect replacement! This mechanical device is designed to work with most floor jacks and will secure the floor jack when being used.
To get yours, visit agatools.com/p... or call us at 760-738-4084. Want to email us? Reach us at rich@agatools.com!
This could be useful but it does not replace jack stands, you just can't leave a car jacked up that high by only one point while you get under it to work on it.
Is the front bar on all jacks rated to hold the weight of a vehicle?
This is ingenious! You guys always come up with great ideas. I own several of your tools.
But the fact the jack is still on its wheels scares me
I’ve never had a jack roll on me to be honest. Usually what happens if you are at an angle is the jack will begin to lean and want to roll over. But I understand your concern.
I always use a wedge both ways.
a driver extension on front and rear of the jack wheels is easy fix for fear of rolling
Brilliant idea. This makes great gifts
Wow nice product 😮 the first seen for me shipping to Germany?
So the Jack Rod falls off if the jack is jacked up higher? It seems you would have to remove the Jack Rod, jack the car up more, install the Jack Rod, then raise the jack a bit more until the safety peg finds a hole?
If jack rod is installed and vehicle needs to be lifted high, just lift the vehicle higher and pull the trigger on the Jack Rod Stand. Because it's spring assisted, it will extend the Jack Rod Stand. If it's not sitting in the detent hole, just release the pressure on the hydraulics and everything will lock into place.
@@AGATools Maybe it's just me, but if the Jack Rod is installed and locked into a hole, how can you first lift the vehicle without the Jack Rod falling off? You could raise the vehicle about 1/2 in before the Jack Rod end is no longer in contact with the jacks support bar. You can't jack up the vehicle and pull the trigger on the Jack Rod at the same time. Maybe you should make a short video to demonstrate the technique.
Thanks for ideas
What’s difference between AGA jack rod and AGM jack rod? AGM didn’t have the label made in usa
En mexico como lo buscamos
En Mexico dónde lo venden
aren't most consumer vehicle jack stands good for 3 tons?
There's a mixture of both. So what we are doing in the near future is have a Jack Rod Stand for both 2 ton jacks and 3 ton jacks.
Can that lever be locked in? Afraid of accidentally kicking it while under.
With the load on the floor jack, it will require A LOT of force to activating the lever.
@@AGATools So it is possible?
@@sjagain Anything is possible, like somebody could come along and let the jack down while you are under it or a sink hole could develop right under your jack.
will it work on the 1.5 ton floor jack ?
Joe, is the front axle/roller the skinny version or is it bigger diameter axle/roller? If it's the skinny one, then our tool will work.
@@AGATools Is the front bar on all jacks rated to hold the weight of a vehicle?
Man no. Man absolutely no.
Schade dass es so teuer ist, hätte sonst eins bestellt, sieht mega praktisch aus, aber für den Preis niemals
$140.00 is expensive? We work on cars that at times cost more than houses. Is your life not worth 140.00? Mine is priceless.
@@lynxstarautomotive208 na wenn dein Leben unbezahlbar ist dann kann das Ding ja ruhig 1400 kosten🤦🏻♂️ das ist nur ein Stück Metall, an sich eine gute Idee aber der Preis macht alles kaputt. Wenn du an Autos arbeitest die mehr als ein Haus kosten, dann kannst du dir bestimmt eine vernünftige Hebebühne leisten, das ist einfach ein dummer Kommentar mein Freund.
You are using my video footage that has copy right statues. Please remove the footage from you video or I will take legal action against you.
😂 free use homie. Sorry you fucked your car, but not a thing you can do about that 2 sec clip.
Bwahahahaha!!!! This guy!
🤣
Not sure which is more hilarious and pathetic, the fact this guy’s clip shows he crumpled the rocker panel by being an idiot, or that he tried to instill fear of legal action to enforce protections under the “copy right statues” 🗽🗽🗽
I’ve been a lawyer for 23 years. I wish I got a nickel for every empty threat like this that I’ve come across…. Then I could afford a JackRod AND a JackRodXL!!
I wouldnt trust this stand. Wait few more years
You're using a 6 ton jack stand which is way taller than the conventional 3 ton stand. That is deceiving to people who aren't familiar with these tools being used everyday. Your welcome, your trusty bodyman who uses tools everyday.