Video

Any photos of Wire diagram for limit switch and possible motor if possible?

When everything is in its place it's like your life is more organized too. It's good to keep things organized

Would this work on the old expandas 17 series were hard lif comes up from bottom ?

Awesome vid mate. Just curious and could be a silly question but was the thick red wire in the anderson plug the negative or positive? Thanks

I put grease in my plug it just keeps all the dirt n water out

You're the only one that's done the install the easy way. Every other video I've seen has people pulling the top part of the dash apart just to get the bottom trim off. About to find out firsthand myself

Thank you so damn much!!!!!!!!!!!!!!!! I could not figure this out! You're the best!!!! Cheers!!!!!

Great vid, well done. I've always wanted to build one, I might have to give it a crack. Cheers.

Is this a concrete filled bollard?

Like a bought one. Great video

Howdy Shed Seth , I am trying to FIX my 1968 HOLDEN KINGSWOOD HK Window Winding Mechanism . Rare Spares don't makes these parts . Thanks for your video . ROBBIE 🐎🏁

Cool. Not sure what you painted it with. I prefer a stove black/paste.

Hi.just saw yr vid.some reaserh.the thick red and earth white aren't they for the caravan fridge....cheers

Thanks for this. Been rattling my brain for a day.

Giddyup, I'm right with ya.

Awesome mate, I was searching for White Knight 300g Pot Belly Black and this video came up cool, was checking to see what it looked like, going to maybe try this on my extractors of the new HJ I picked up 😂

Cool car on the lift! What is it?

Put a very similar looking 2-post lift in my new "shop" as we call them in America. Can't wait to actually use it. Thanks for sharing your experience! Question: why are Aussie sheds uninsulated metal? Seems it would get terribly warm, or cold. Or is it a building code thing?

Thanks for the vid. I have a BA ute and I was thinking about tub removal and putting a tray on, but liked the idea of a tub trailer since no one is doing them these days and scrapping the tub seemed wasteful. But I had no idea what to do about trailer frames, suspension or axles so your vid was very helpful for me to understand some key points. By the way nice holden coupe in the background?. LE or HQ monaro?

Awesome video. Just what I needed.

So do you have to maintain the horrible indicators if you put a Hq bumper on? I don’t want to put the commercial bumper back on and want to use the Hq one.

Hey mate, love it, just got the tub off my Ute and wanna do the same thing. How did you go with registering it if you did? Thanks mate

Legend mate I'm ripping an hx ute apart and I was about to spit the dummy and break something 😅 Life saver 👍

Was going to ask what happened with the one tonner as it had been a while, hope you get back into it soon.

Hi mate what’s the whole exhaust setup on this ?

Looks great! How is it, may well enquire with them for one!!! What did they seal the collar with into the ground with?

I put mine in on my sv6 and now I’ve got a safety and power reduced fault idk what i did wrong

Never too much details, mate. Perfectly explained. The only vid I need to watch on this subject. Thanks

How thick was your concrete floor? Mine is 100mm, thick enough for those anchors do you think?

I bought a 100+ year old comfort potbellied stove that was in great condition but rusty, I just applied stove polish right over the rust.Its just carbon black and a soft wax. Use a damp cloth and it polishes to a high shine. it is fireproof and just needs to touch up every year or so. Barbecue paint will grey out .

Hey mate did you have to upgrade the struts at all?

Common problem on 308's with high km's on them, happened to me, the taping noise on my engine was the valve pushing the piston top down as the top separated from the rod and pin

As far as home wiring jobs go, yours is one of the better examples. You didnt use a vice or angle cutters to try and crimp the wires.. Only changes I would make is to use heat shrink instead of electrical tape, and expose a bit more of the wire going into the anderson pins,, (use heat shrink to secure the braided sheathing to the pins as well.. Over al, well done. (P.S. I am picky with wiring/crimping, as I an an RAAF trained Avionics Tech/Elec fitter of 50 odd years experience)

Also, why did you decide to paint it instead of seasoning your stove?

Question…I have the same stove. However, I’m missing the middle piece with the door. Is there anyplace where I can get this missing portion? Thank you!

any reason to not crimp the Anderson lugs in, done in like 30 seconds vs soldering? from what I've heard soldering can fail - at least when done DIY, so crimping would seem a better idea for DIY

This is bloody brilliant design. Go the Aussies!

Thank you so much tht was a amazing video im definitely gana older one for my 2005 Holden commodore vz tht was amazing 😍😍😍

Is ur buttons really stiff ? Coz i bought one and the of the buttons not even pressing

Hey mate. Would it be too much to ask for the plans or dimensions of your bottom under-tub parts? Mine has a canopy and it's VERY heavy and I cannot flip it over to measure it

Good video

Bad video

Hahaha!

Just make sure the vegan teacher doesn’t find that place…

last*

So many tasty things!

Yew!.... Mate,good to see you back on da Tube..1k subs. Congrats. I found you via One tonners. Mine hasn't progressed much either. Life gets busy. Glad to see your doing some stuff. And a digger. Sweet.....

I’m off to the shed right now!

Wicked update bro, missed ya too, glad you picked up that property sounds great, want to buy something similar one day 💙

Good on ya Damo! Lots of developments for sure. Gotta catch up bud. Take it easy…