Video

There's no timing affected. No worries.

It's an expression pedal and can control functions in a device, such as a volume function in the QC. However, one can not send audio signal through an expression pedal.

Yes.

@@LehleSwitcher Thank you!

Yes!

@@LehleSwitcher Thank you.

@@LehleSwitcher Thank you.

Basically - yes. In this particular case the 50K is the socket you use to manipulate the expression with (which can be then vol, wah, mix of a delay, whatsoever in your QC) and the 10K is configured as a switching socket, which toggles a function at the QC.

@@LehleSwitcher My use case would be that I want to use this expression pedal to control two parameters of the same QC effect/block independently - meaning that I would like to switch between expression 1 and expression 2. When I try to calibrate the pedal in QC or try different setting on Lehle it always controls two parameters at once instead of switching between 1 and 2. How can I solve my problem?

@@DG-km3el Sorry, but we can't help - I think this is a case for @NeuralDSP support

Hey Luca - if you haven't been successful yet, send us a mail to support at lehle.com

Yes, this might be version 1 and does not work with momentary SPST switches.

As shown in the video, you can use the expression for anything. Then triggered by the switch of the 10K socket, the QC can activate module X and deactivate module Y. The videos just shows an application which is handy.

No problem! The point where the switch trigger, can be calibrated. Simple take a look at the manual and calibrate the pedal or write us mail.

I have the same problem even after calibration. Did you solve the problem?

@@tanggenius3371 no I didn’t

Can you make video how to calibrate the dual expression so it will not switch when I use it manually, so only when you push it by your foot

Did you solve it? I would like this one if it works properly.

Would you please send us a mail to support at lehle-components.com ?

@vovokidx9691 I've only ever used 9V so regrettably I do not know! Usually it's best to only do what is recommended on the product page, I'd assume Lehle products are 9v.

@@vovokidx9691 no idea unfortunately

Unfortunately we haven't had one in our hands. Open it and send us a few pics by mail!

If you want to get this issue solved, please write us a mail: support at lehle.com

If you want to get this issue solved, please write us a mail: support at lehle.com

Is there a guide on how to use it with HX Stomp?@@LehleSwitcher

Der rote ist ein "Klon KTR Centaur".

Yes this should work fine.

To answer your question: yes, it can be used "in reverse".

There's no need to add a buffer at the end of a pedal chain.

Signal-quality-wise it's the same. The LITTLE DUAL II switches a bit faster and probably quieter. It really depends on which features you need (e.g. MIDI, T output, etc) and then decide. You can send us a mail to support at lehle.com

@@LehleSwitcher Clear. Thank you very much for your fast reply!

Yes you can, but since the T output is not isolated from B, there's a probability you need to isolate this one, too, if you get hum or noise. A LEHLE P-SPLIT III or a LEHLE P-ISO can help.

Die Verbindung des LEHLE DUAL EXPRESSION zum Line6 funktioniert wie mit jedem anderen Expression Pedal auch. Es gibt da keine Besonderheit. Was du alles mit einem Expression Pedal im Line6 anstellen kannst, findest du im Handbuch deines Line6 Geräts. Die Vorteile des LEHLE DUAL EXPRESSION liegen auf der Hand: verschleißfrei, präzise, MIDI, Schaltausgang und so weiter. Mehr Informationen findest du unter www.expression-pedal.com

@@LehleSwitcher Hello, ich habe Ihnen eine Nachricht geschickt, aber noch keine Antwort von Ihnen erhalten. Ich würde gerne wissen, ob ich die SPLIT-Box wie die Radial Reamp HP Passive Reamping-Box verwenden kann, d.h. mit dem Ausgang "Headphones" Lesen Sie Ihre E-Mails !

@@kianhendrick3794 we got your mail and answered on October, 19th. Pretty sure it's in your spam. You're welcome!

The one you are looking at is not available anymore. The current version is the LEHLE PARALLEL SW II and is not only a "line mixer with a footswitch": • True-Bypass parallel effects looper and stereo mixer • Discrete Class A input stages • 122 dB dynamic range thanks to 30 V technology • Latching, Momentary or Mixed Mode operation • Mono and Stereo functionality • Active pop suppression circuit

An ABY without footswitch is basically the P-SPLIT.

@@LehleSwitcher SO I can also use the P split from guitar to Volume S and then to P split and then both outputs to my quad cortex inputs 1 and 2?

Robert, we are discussing this topic by mail already. Did you got our mail?

@@LehleSwitcher yes I received it but I wanted just confirmation that ps plit can be used as welk because I need to out it under my biard because I dont have enough space at the top.

@@robertmiddel5582 The P-SPLIT III can split a signal into two signals. Nevertheless I am not convinced that it's the correct device for your application.

There will be a successor of the still available original LEHLE MONO VOLUME. But it's not clear when. In any case not in 2022. So right know you might decide between the available.

@@LehleSwitcher Your new one with MIDI capability and 120db range sounds amazing; will be getting one. :)

@@LehleSwitcher I also want a MIDI capable pedal but the original size. I'm a producer, not a gigging musician, so larger is better since it's means more control... I have no need to fit everything on a small pedal board. There aren't any other pedals on the market that do both volume and MIDI, so I think you could really corner the market if you make a full-size version with MIDI control. Hope it doesn't take you too long to make it! In the meantime I have to use the Moog EP3 for MIDI and it sucks :-/

@@jonlemmon2718 We're working on that.

It's 50% lighter and 35% smaller: instagram.com/p/Ccp3pV9sux9/

Thank you, I look forward to trying one soon.

Sorry that it didn't work out immediately. A mistake often done is the wrong connection. Did you exactly solder them shown with the glasses at 2:12 ?

Awesome! Thanks!

You probably bought the old PARALLEL L which is mono and read the manual of the PARALLEL SW II which is stereo. Could you better write us a mail? support@lehle.com

That's why the new LEHLE PARALLEL SW II is stereo: lehle.com/EN/Lehle-Parallel-SW-II czcams.com/video/qQGu2-0tCXc/video.html

Hey Alan, these are stereo jacks! lehle.com/EN/Lehle-Parallel-SW-II

Say if I’m running an Eventide eclipse that has two inputs and two outputs, how would I hook this up if I want to run into both inputs and run both outputs out of my eclipse back into the lehle? Does the send jack on the lehle work as a send jack that I would use a trs stereo out to to a dual mono split cable or does it function as an insert jack? My eclipse has a left and right input and also a left and right out put. I use a lot of ping pong delays that bounce back and forth from the left to the right ear. I am also running out to two amps that I run at the same time.

@@brighton09100 Please go the product page: lehle.com/EN/Lehle-Parallel-SW-II All necessary informations, pictures manual and so on are available there. All the jacks (input, send, return and output) are usable in stereo via TRS.

@@LehleSwitcher no it doesn’t give you the details on the cords. The pictures show 1 cord going into the rack and one cord coming out. For a stereo effects rack that has two ins and two outs, it’s impossible to get true stereo effects without some kind of y cord or insert cable. Even then, you can only run out to one amp. You would need two 1/4” jacks running out of this box to get true stereo out. Not making much sense. You would basically need two of these to get true stereo.

@@brighton09100 Of course you need cables which have TRS - 2xTS.

Thanks ❤️

@@LehleSwitcher Can I ask what brand of cables he's using in the video? Thanks

@@ivoleary6332 I really can't remember, but you can ask of course Markus: instagram.com/birklemarkus

Absolutely!

You can use either the DUAL LOCK Mounting Kit: www.lehle-components.com/en/3m-dual-lock-mounting-kit-for-lehle-pedals.html Or you use screws: www.lehle-components.com/en/lehle-mounting-kit-v3.html In the manual on page 8 it's described how to fix the pedal on a board www.lehle.com/_data/products/Sunday%20Driver%20SW/Manual/Lehle-Sunday-Driver-SW-EN.pdf

Please watch the video in English language: czcams.com/video/pxgT6M9V_Cw/video.html