Video

Ugh CANT WAIT!!

No need to mask the disc mounting area?

I gather you’re not in this as a business actually. You need to determine your out of pockets and set a flat fee for prep. Make a determination of the cost of electricity for six months to a year for the shop. Do the same for your expendables (I.e., blasting media, chemicals, nitrile gloves, nozzles, equipment maintenance, building maintenance, insurance, etc.). Determine how many products you completed over that period and divide that number into the those total costs. Don’t try to weight the size of the project into determining that result. After you have come up with that figure make a decision on what constitutes a small, medium, or large project. For each size project, assign a margin figure based on a business math percentage of the annual piecemeal number you came up with. For example, say you have a piece that is less than approximately a square foot or several pieces that aggregates to about a square foot in surface area you could do a 10% markup to determine your flat fee. Do the same for the medium and large flat fees as well. On your bill keep the flat fee, the man hours, and powder media on separate lines of the bill. To be successful, you’re going to have to be consistent or your customers aren’t going to trust. I spent quite a few years as a wholesale buyer for a large national company and I can tell you if you aren’t savvy in business math, you’re going to be in a world of hurt. The best thing you can do is get a knowledgeable bookkeeper to help you set up your books. Believe me, laboring in the oven is not even half work of making and growing a successful business.

Do you use any degreaser after blasting?

Nice, where's the after?👍

Just got one can wait to use it.

What kind of stripper are you using or where do you get it?

Do you offer someone to pay for a small phone call conference to help with powder coating questions? I feel like i saw in a video once you said you would do that, thank you

Is your neutralizing tank a mixture of water and baking soda, if so what is your ratio?

Anucia broder anucia internet shops put all the 200 and some body weith on abvertizing

I was the thousandth like 😎good vid man

Can I cut the sire going to the gun and put a plug on it so I don't have to drag the whole kit with the gun?

Can I cut the wire going to the Eastwood gun and put an automotive plug on it so I don't have to drage the whole kit with the gun?

I really enjoy your content man and when I was watching a video from a year or so ago and you did not have a wireless microphone on and I can barely hear you I thought oh man I’m sure he got one so I jumped to the newest video still no wireless Mike look into them. They’re like 20 bucks dude it’d be so much better. I love the content. Just trying to help. And I was listening to you from my television in my home with a surroundsound system. I had to turn it up..

I need one of those hopper holders.

Thanks for the info. I have a new one that I will modify. The existing parts suck. What grit and type media were you using and what size tip? Compressor size? Thanks again

I'm having a shop re-do my wheels right now because of way too much orange peel on the wheels they did for me. I am however somewhat worried about the wheels loosing some of their structural durability goes as far as metal hardness and what not. Is it okay to sandblast and heat up alimunim alloy wheels twice? The wheel manufacturer Enkei will actually downright void your warranty on wheels you buy from them if you even powdercoat them once. Should I worried? I drive a Lexus GX 460 and the wheels I bought for it are 17" AGP Wheels. I plan on keeping this vehicle and these wheels on it for a long time.

Looks really good 👍

Loose the music people with hearing aids can’t hear you ,is there chrome power coat ?

sometimes when I spray clear vision it doesn't lay the same as the clear and ends up going on in splotches (usually it all melts away but sometimes you can see it in the finish, what causes this?

Been loving my RC2. Went from a Hypersmooth 03 and this thing just lays down like glass. I have better control of my powder flow and I don't have to tap the hopper constantly to maintain powder flow to the gun allowing me to lay down more even, smoother coats.

does touching the part to rotate it introduce grease that can affect the finish?

if you like bones check out $uicideboy$

This video narrated by Matt Saracen. LOL

So the powder won’t flow into the areas I take it.

Glad I seen this before cutting a couple holes towards the top off center like cycle fab recommend! I’m sure his mod helps but this seems like it may be the better mod. Quick question. Could I use an old big air compressor that has rust and a a lot of moisture inside or would your recommend I get a small brand new 4 gal air compressor instead? I’ve already got moisture and oil filter on the gun. TIA!

I would like to see a comparison on the different guns, and what bigger money gets you….

I would like to see a comparison on the different guns, and what bigger money gets you….

Solid video, the volume is all over the place though, having to adjust it to hear what your saying. Sure you know after 2 years though haha

bro this kit can be used with the hypersmooth 3.0?

Also use a deburring tool after clear coat

I’m trying to get into powder coating. Building an oven. 15 months in. Not much help from other people. Started 15 months ago was tired of powder coating coming up on my phone. Decided to watch. Got hooked right then. How simple it could be. With a regular oven. But I wanted something that would hold a differential at least. 2 am. By 9: am I was going at it. Small town not many options for materials. No plan,no knowledge no idea what i was really doing. I am making it with electricity and propane. Because electricity costs are crazy expensive. In a town that gets 115~122 degrees in the summer.May never even use electricity. Think it was a waste $ but couldn’t get any advice from many people. 200 videos like yours. Helped me design what I thought that I wanted.thanks for your time. I want to be fair to people also. 8x7x6 ft.

I’m trying to get into powder coating. Building an oven. 15 months in. Not much help from other people. Started 15 months ago was tired of powder coating coming up on my phone. Decided to watch. Got hooked right then. How simple it could be. With a regular oven. But I wanted something that would hold a differential at least. 2 am. By 9: am I was going at it. Small town not many options for materials. No plan,no knowledge no idea what i was really doing. I am making it with electricity and propane. Because electricity costs are crazy expensive. In a town that gets 115~122 degrees in the summer.May never even use electricity. Think it was a waste $ but couldn’t get any advice from many people. 200 videos like yours. Helped me design what I thought that I wanted.thanks for your time. I want to be fair to people also.

Amazing work they look fantastic 👌🏻

Where did you get the aluminum sheets from

You can use a sieve to remove paint residue from the drum.

I’m 2 years late. But call them “twister tips”

here in ph , 50kg of methyline chloride cost 10,000 pesos. the most effective way on stripping

Awesome thanks!! Inspiration slap to the head

Bro, you are awesome. I am planning to Powder coat my motorcycle rims but I am here in California, by you just making this video I would take my rims to you if you were in California. I will follow you because you are an honest person. I am sure you will get a lot of customers because media spreads like wild fire.

Hey what did you use to plug up the holes and cover up the piston slots?? Thanks hope to hear back

Do you ever spray parts hot or only at room temp? Like if you were doing a base and a clear top?

It does use a electronic charger to make powder stick,correct?

Whats the ratio on baking soda to water?

Where u get the plugging plugs from?

What color is that at 32:51? Chartreuse? Who’s it through?

Can u give me some insight as to why I'm continually getting orange peel on my parts but the wheel hangers, "which are eye bolts" look amazingly perfect.?

Chemicals?! Name please?! Thank you in advance!

What do you use for paint stripper and neutralizer tank

No matter what I tried with the rc1 I couldn't get it to do a 2nd coat properly. The rc2 will do 3 and 4 coats efficiently so far.