14Point7 Spartan 3 Lite + JRP Edge 52mm Air Fuel Ratio Gauge Wideband Install
Vložit
- čas přidán 28. 08. 2024
- In this video we are going to show you how to correctly wire up the Spartan 3 Lite & also how to connect it to the JRP Edge 52mm air fuel ratio gauge.
It is important that when doing your Spartan 3 Lite wideband install you get the wiring correct, so in this video we walk you through the process and make sure you also know how to connect it up correctly to the JRP 52mm Edge Air Fuel Ratio gauge.
If you found this video and are looking for a wideband kit to install, feel free to give us a yell at Just Race Parts and we will be only too happy to help.
✅ For more information on the 14Point7 Spartan 3 Lite + 52mm JRP Edge Air Fuel Ratio wideband kit, checkout the link below.👇
➡️ Spartan 3 Lite Wideband Gauge Kit 52mm LCD & 02 Sensor
www.justracepa...
➡️ Our Full Range Of Wideband / Air Fuel Ratio Gauges & Kits
www.justracepa...
0:20 ✅Power Circuit Setup
1:10 ✅IMPORTANT! ENGINE GROUND
1:30 ✅Connect to JRP AFR Gauge
1:55 ✅ECU + Data Logger
2:19 ✅Factory ECU Integration with Narrow Band Simulation
2:53 ✅Explain Power Wires on Edge Gauge
hey man, can we please get a few vids on the 52mm guages. espcially the dual EGT & Boost, wanna see how it operates before i purchase. cheers
Hey Harrison,
We have plans to do a walkthrough video for the Edge 52mm, but it’s not scheduled to be filmed until maybe mid to end of Sept.
Did you watch the video from Aussie Arvos where Patrick installed the Dual Boost & EGT plus the Water Temp?
Also welcome to shoot us an email and ask for a copy of the manual, that runs over everything in detail as well.
czcams.com/video/KDg3wbW6TJA/video.html
Can i use the 12V +/- of the original O2 sensor Heater to Power Teminal 3/4?
Hi Alexandros, Thank-you for the message. No, Generally its best to follow the guide lines we put together in this video (and instructions) for successful installs + Spartan and Sensor longevity.
The kit comes with a pod for the gauge, which is a really loose fit. What's the recommended procedure for fitting the gauge to the pod? Kit has a bag with 3 screws and 2 strips of foam, but they are sticky on both sides.
Call or Direct message us on our Facebook page, we should be able to assist you further (send through some photos). There are one of 2x foam styles tapes that have been included depending on the age of your purchase. We have a Gauge mounting video as a work InProgress at the moment.
Thank-you
Is it absolutely necessary to ground them to the chassis and block? What would happen if I grounded them to my headunit wiring. On the Spartan 3 lite manual it doesn't give any recommendations for terminal 2 ground but for terminal 4 it says chassis and no mention of the block so could I do that also? Thanks
YES it is the BEST practice to do so if you want to take advantage of ACCURATE Spartan AFR readings. Part of the Spartans design architecture does indeed have a ground offset used to stabilise the data readings. Please avoid using a grounds off a head unit/ sound systems! This will lead to unexpected readings from electrical interferences. Terminal 2 is best to ground off ecu ground.
Feel free to call or email Just Race Parts for more info. :)
Is the spartan 2 sill supported by the JRP 14 in 1?
Are there examples of folks mounting the spartan?
Would this be ok to run through a haltech expander box?
Thanks for the message, Your best off emailing or calling through for more accurate information. Spartan 3 Can has been used with Haltech products and can be custom programmed.
Older ECU's and data loggers can also work with the analog 0-5v linear output.
@@JustRaceParts will do! Thankyou
Hey, is there a cable in the kit to connect the O2 sensor to this ecu? Nothing is said about that in this video. Cheers.
Terminal 6 is used to connect to gauges, ecu's, dataloggers. It's the same for all, just run a wire from terminal 6. If running to a gauge and ecu, single wire from terminal 6 and then have it join to each wire running off to gauge / ecu etc.
@@JustRaceParts Thanks for that. But I meant: the connection from the O2-sensor (located in the exhaust) to the Spartan 3 ecu. It's not clear for me if that cable (loom) is provided with this kit. Cheers.
@@Oscar-eb5rc All of the Spartan 3 kits we sell come with an 02 sensor, and also a cable that connects from the Spartan wideband controller itself to the supplied 02 sensor. You can only use the 02 sensors provided with the kits, you don't use any 02 sensors that are installed prior to using the Spartan.
Any other questions feel free to email us. ;)
@@JustRaceParts Thanks a lot.
@@Oscar-eb5rc Welcome. ;)
Can we use the same power source for for power 1&3 ?
Yes, but remember to separate the two grounds. Terminal 4 ground is best placed on the block.
hey man, is this product available?
They are on pre-order, shoot us an email and asked to be added to the pre-order list. They are selling out before the shipments even arrive, so best to get added to the list so you can secure a unit from the next shipment due in around 6-8 weeks from now. ;)
Wow you ready to take a liability of failed sensors ? Because you don't mention anywhere that that the spartan box can't be powered unless the engine is running
That’s because the manual that is supplied with the Spartan 3 runs over that. This video was more of a guide to help people better understand the manual by seeing what connects where and just give a visual to the manual.
@@JustRaceParts ok i still think it should be included in this video. As probbaly the majority of people are referring to this video for guidance.
It says 12v ignition on the pop ups when he mentions the lines