How to Replace Throttle Body Position Sensor 2007-2013 Chevy Silverado
Vložit
- čas přidán 5. 02. 2023
- Buy Now!
New Throttle Position Sensor from 1AAuto.com 1aau.to/ia/ACTPS00001
This video shows you how to install a new throttle position sensor on your 2007-2013 Chevy Silverado.
This process should be similar on the following vehicles:
2007 Chevrolet Silverado 1500
2008 Chevrolet Silverado 1500
2009 Chevrolet Silverado 1500
2010 Chevrolet Silverado 1500
2011 Chevrolet Silverado 1500
2012 Chevrolet Silverado 1500
2013 Chevrolet Silverado 1500
Tools you will need:
• Flat Blade Screwdriver 1aau.to/oa7P/1AXAA00013
• 10mm Socket 1aau.to/oaSj/1AXAA00017
• 8mm Socket 1aau.to/oaSj/1AXAA00017
• Trim Tool Set 1aau.to/oYL/1AXXX00006
• Ratchet 1aau.to/obk6/1AXAA00016
• Cloth Rags 1aau.to/oym/1AXSS00035
• Pick 1aau.to/oGp/1AXAA00037
Subscribe: / @trq
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video. - Auta a dopravní prostředky
√ Watch the Video
√ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts
√ Do it Yourself
√ Save Money
For all those why open blade....it then will line up shaft of motor with the slotted hole in the assembly when you put it on.
Will a faulty TBPS cause shifting delays, rpm jumps etc?
This video was great. It help me change the throttle sensor and programmed it like he said. Good job on this video
Fantastic video, thank you! I lucked out, my idle improved instead of running too high.
What happens if I don’t hold blade open while putting the sensor on
Thanks for the video. This was helpful.
Around 2006-07 there seem to be multiple throttle position sensor setups on these and it's hard to look up exact info on what goes with what if you haven't looked under the hood. I have a 2006 4.8 with the sensor that looks like this. Some of them around the same time seem to be the kind in your other video where you have to remove the alternator to get to it. The type that look like this are sometimes held on with these clips, and seomtimes they are riveted on and the replacement parts come with bolts.
For the riveted version of this, does anyone know if I can do it without removing the vehicle or does the open blade issue require that you take out the throttle body to change the sensor?
Many thanks for you, bro
Thanks 🙏🏼
Good 👍👍👍👍👍👍
So you don’t need blade open but you might need to push it open to pit properly on tps line it up. The clips are a pain but I just put it on tps first then use flat head on the other side of clip. Flat on top and two handed in on. Hope that make sense. Then you need to do relearn procedure. 3min on 1 min off x2
Rpm’s will shoot up to like 3k but it will go down if all is well. Hope this helps.
What he didn’t tell you is if you vehicle is running at 2,500 rpm idel and you throw it in drive you’ll be spend a lot more in a transmission rebuild
Can anyone tell me what to do if i didnt hild the throttle plate open the first time i took it out of the truck? PLEASSSSSE HELP!!!
Does it have a iac valve
Why would you open the throttle? I did that and now my idle is running at 3k rpm’s and is way off. Nothing I do is leveling it out.
Ty
How often do these sensors go out
What if you do this without opening the throttle??
👍👍👍
You dont have to take the whole throttle body out
My check engine light goes on while idling...and goes off st 25mph...it's a new throttle body and has been programmed..
Why with the throttle blade open
Did you say 89 inch pounds 😵😓
One of the reasons I don’t like this channel is because they don’t ever answer any questions