E39 Trans Fluid Level Check and Top Off

Sdílet
Vložit
  • čas přidán 8. 04. 2021
  • How to check the transmission fluid on your E39 BMW 530i. Automatic Transmission ZF5HP19.
  • Auta a dopravní prostředky

Komentáře • 24

  • @mikebills9343
    @mikebills9343 Před 2 lety

    Thanks for the demo

  • @HellaRandomVideos
    @HellaRandomVideos Před 3 lety +2

    I can👃 it from here. Thanks for the tips!

  • @GregoryEsman
    @GregoryEsman Před 3 lety +1

    Thanks for the video! Would you please link the exact cable you used for INPA to read your car's data? Thank you

    • @williefast99
      @williefast99  Před 3 lety +1

      Taotao Inpa Cable with Switch FT232RL K+D CAN USB Interface Cable Car Ediabas K+ Dcan USB OBD2 OBDii Diagnostic Scanner for BMW www.amazon.com/dp/B07L498NGZ/ref=cm_sw_r_cp_api_glt_fabc_JN5G3208XBKMEGEWMW7M

    • @GregoryEsman
      @GregoryEsman Před 2 lety

      @@williefast99 Thank you 😊

  • @MRXCHRISS
    @MRXCHRISS Před 3 lety +1

    Question on your Rhino ramps. I have always drove up on them front end only. Any different driving reversing up on the rear tires? Need to check my transmission oil level. I have the 16,000 Rhino ramps. Hope they fit 275 tires.

    • @williefast99
      @williefast99  Před 3 lety

      No different reversing on them. Shouldn’t matter for checking trans. I

  • @kaywonderer
    @kaywonderer Před rokem

    why don't you just go for drive to heat it up instead of idling?

  • @chrismason598
    @chrismason598 Před 2 lety

    What was wrong with the torque converter?

    • @williefast99
      @williefast99  Před 2 lety

      It had a bad seal and wouldn’t go into lockup.

    • @jojo-vc6qe
      @jojo-vc6qe Před 2 lety

      @@williefast99 could you give me a quick run down on how you fixed it. I switched transmissions and it will rarely work like it should before going to trans. fail safe mode. I been riding it like this since November

    • @williefast99
      @williefast99  Před 2 lety +1

      @@jojo-vc6qe I installed the Transgo pressure regulator and replaced the bad torque converter. Mine wasn’t going into fail safe mode though.

    • @anthonywilliams1616
      @anthonywilliams1616 Před rokem

      @@williefast99 how could you tell it wasn’t going into lockup? I think mine has the same common seal leak but it’s low on fluid and I plan to fill it up and see if it fixes anything.

    • @williefast99
      @williefast99  Před rokem +1

      @@anthonywilliams1616 it should run 2750rpms at 80mph. If you’re at 3000 it’s not locking up

  • @dgod6715
    @dgod6715 Před 2 lety +1

    What size socket

  • @thechronic555
    @thechronic555 Před měsícem

    Ok nah bro. You filled it when it was too hot first and youre instructing to fill it after measuring it cold. A simple zip thru the gears with ensure its distributed properly as you fill it but the whole thing should be simplly one "safe" warm reading.

    • @92hoe_club
      @92hoe_club Před měsícem

      Sounds like you don’t know what you’re talking about.

  • @captainfallsalotatppic2508

    Thanks for the sharing of the the video. Your carpet is dirty! Pull out your seats and do a real good vacuum and shampoo! I don't mean to criticize and I do apologize for my doing so; however, I could not live with my baby having dirty interior. I am a total freak when it comes to my Bimmer's health and hygiene. I keep my baby running and looking like brand new. As a matter of fact, I have an appointment in June to get her paint completely stripped down to bare metal and repainted the same as factory color, topcoat and whatever coats the factory applies to the body.

    • @williefast99
      @williefast99  Před 3 lety

      Haha. I will clean it one of these days. Seems like I spill my coffee at least once a month in this thing.