I noticed alot of common comments but really know defined answer to this issue. So I went through the comments and wrote down the most brought up issue wich was the throttle body. Then started watching videos based on that. I took it to autozone to confirm. Came back as throttle body sensor. So 2 choices. Buy a new throttle buddy $350 lowest price for my vehicle or clean the one I have. I bought some throttle body cleaner and removed that part. It was totally black. Sprayed and wiped twice and it was shiny gold. Connected back to vehicle and the check engine light is gone. Been driving most of the day off and on and still no tool light no check engine. This fix cost me less than $10( cost of throttle body cleaner) Hope this helps. My situation was pretty much the same as the person that uploaded this video.
I think the reason for the conflicting comments is that it is the "check engine" light. I can be coming on for a multitude of reasons. I have a 2010 Fusion Hybrid and the light came on while in Florida. Stayed on the entire week. Fueld at the midpoint in GA. Never came on again for years. Then one day driving at high speed it came on. Went off later. Again a couple of years later, it came on again. It's always in high humidity and heat! My problem does not effect power and always the hybrid wreck comes on first, followed by the gas engine wrench.
This happened to me on my 2008 Edge, brought it to the dealer, this is caused by two sensors in the power train which need to be replaced would cost me $750 to fix, I haven't done the repair yet. This really sucks, I am finding out this problem is very common now in Ford vehicles. We should get a class action lawsuit started.
Be persistent it should be covered under the powertrain warranty plus you could call Ford and ask for the customer satisfaction program a representative there will give you a claim number and you can follow up with them about the repair
@@nathatmed6484 they never admitted to a failure of the electric throttle body much less a recall, there thing is that we have to run a diagnostics check first then they will replace it at no cost to you provided it is still under warranty for the powertrain. I would still follow the steps above and try to take some video of the problem happening so you can have some ammo on your side also look on the web and try to find some corresponding info from others like us. Good luck to you, I can promptly holler back too 😎
Did they tell you how long the power train warranty is for? And does it cover it? I'm in el paso, any specific ford you took it to? Sorry for all the questions, just happened today
I have a 2006 ford fivehundred that has been doing the same thing , turns out the wiring harness on this model and the 2005 and 2007 runs right across the top of the enging. Over the years the constant heat from the engine had melted wire into in numerous spots and they were touching. It's why it does it going down the road instead of starting that way. Because bumps and holes in the road or whatever tmcan make those wires not touch and when you restart it itll crank up normal. But drive a mile down the road and hit a hole just right and those wires will touch together again and put it back into limp mode.
So I have a 2005 Ford Five Hundred that is randomly doing the exact same thing "engine safe mode" with a wrench. Pulled Codes P2104 Forced Throttle and P2112 Throttle stuck closed so I replaced the throttle body and still doing the same thing. I'm thinking this is also a wiring short or ground that's causing this intermittent issue. I'll check the wire harness that you mentioned to see if it's heat damaged by engine or friction. Thanks for your post!!
This just happened to me yesterday and I barely made it home. I have not restarted it yet but I hope it is no problem and it will work when I use it next...ugh. I only have 55, 000 miles on my taurus 2008.
2009 Mazda Tribute happens alot and check engine light turned on with the code that the Throddle is stuck open. Cleaned ot with a throddle cleaner worked fine for a week and now its shuting down again. Do i need a whole new ETB or just a new sensor dor the air mass flow
My f250 6.0 powerstroke does this too and I don't have the 5k to fix the problem. Just got the truck "as is' 3 months ago, it's a fking disaster, now I'm stuck in a loan. I feel your pain brother.
This may possibly be an oil cooler issue. There is currently an investigation on behalf of consumers who purchased Dorman oil cooler kits for their 2003 - 2010 6.0L Ford Diesel Trucks to replace the factory Ford Oil Cooler. Dorman Oil Coolers are non-OEM (aka aftermarket) oil coolers sold at stores such as NAPA, Advance Auto Parts, Auto Zone and more. The Ford 6.0L Diesel Dorman Oil Cooler kit (part number 904-228) is sold for use in Ford Diesel vehicles made from 2003-2010. It appears that O-rings and gaskets within the kit are believed to deteriorate into small particles (sometimes green or yellow in color) that spread throughout the Ford diesel engine, causing expensive damage. If you purchased a Dorman Oil Cooler, had it installed in your Ford 6.0 Please contact us at Thealertconsumer@gmail.com and tell us your experience. Website is under construction. Find us on facebook @thealertconsumer
I have the Ford Edge 2013, Same thing... It was so dangerous. FORD should do a recall of all vehicles that has a problem with the Electronic Throttle Body. Be careful if you have a Ford!!
Before changing the Throttle Body clean it with a Throttle Body cleaner, that could save you $500, and clean the Mass Air Flow sensor (MAF) with a MAF cleaner.
@@robertzamb that what I said I was going to do. A mechanic here in Houston Texas told me to contact a Ford dealer to find out if it was a recall on this problem
I have a 2014 Ford Edge and the same thing happened to me. The Dealer just called and told me it waa the Throttle body and it will coat $490 to fix. I have only had the car 2 years and a couple months!! I called Ford customer service and of course they did nothing because there is not a recall for my vehicle
Anyone who have this problem if you have these 2 problems if you brake and it takes time to slow down or if you floor the gas pedal and the response hesitate before the wrech light come it’s your Acceleration position pedal sensor. Most people thing it’s the throttle body but the pedal tells the throttle body how much to open or close. If you have a electrical throttle body. Hope this helps had the same problem with my ford mustang
I have a Ford Fusion 2006, this happened to me as I was getting on the freeway in my city. I was doing about 70 and then the vehicle jolted and almost stopped running and my car slipped on ice and swerved into the right lane where a semi was. I was close to hitting it, I'm still pretty shaken up. What can be done? What happened with your vehicle? I read somewhere that this is a safety issue and ford can get a lawsuit filed if they don't fix it???
i have 07 milan its doing the same exact thing...wrench light then going in and out of gears high revs and jerking motion....is yours still running good? , and was there a recall for the throttle body?...there is a recall for the airbags just so u know...they can kill u w metal shrapnel inside them.
I have the same issue right now with my 2010 Fusion everything is cool when the wrench is not on the dash but as soon as it pops up it just stalls like you don't get no speed it'll barely let you move 10 miles an hour but when I took it to AutoZone they said it was a throttle body and this purge valve I changed both of those and it seemed the car was running fine and then it started up again. and it sucks because I have to be in work tomorrow and today is Sunday so I couldn't take it to no shop because there is no mechanics and after I get this situated I'm probably pretty much done with Ford
if I were you I would take it in right away , everyone out there will be glad to know the even if you have a 2009 like my Escape the Electronic Throttle Body will be extended to another 10 years so in my case it is still covered till 2019 , don't be fooled this is a bigger problem than Ford would like to admit, the reason it is not a all out FACTORY RECALL is because Ford got a jump on it and layed it out as a customer service /safety program , in your case 2016 should be covered till 2026
I have a 2007 ford five hundred that's having the same issue. I purchased my car like 4 years ago from Carmart. So will I be able to get it fixed under warranty for free?
Its your ignition coils they are bad, or cracked Giving it a bad signal to transmission, if the transmission is doing weird stuff, and the wrench light comes on and the the traction control light the coils are the problem
So, did you find out what the problem was? Mine just came on Saturday and my car slowed down alot. I cut it off for a few minutes then start the car up and no wrench. Please let me know the diagnosis!
The wrench 🔧 light is a tune up spark plugs and coils you have to use the Oem plugs and coils (Motorcraft) After time the aftermarket plugs cause faluty combustion and the car goes into Limp mode. A bad injector can cause this as well for the most part just add Lucas fuel treatment after changing the plugs and coils.
tonight while driving my 2008 ford fusion home it happened to me , i have noticed in the past a intermitenet rarely engins stall and refire , suddenly the engine drops to 0 rpm then everything back to normal , like 10 random times during the last 2 years , and now tonight the wrench lights up and every 10 minutes complete loss of power and rpm drop to 0 then sudenly everyting is ok , only 53,000 miles , having a ford sucks , i will never have another ford ever
I have a 2007 F150 what does that really mean when you get that cause I did the same as this guy I would love to know is it a problem or something you don’t need to worry about
that's a damm shame it's still under factory warranty, don't give up ! Too bad it's 4th of July weekend , but that's bull shit don't give every time the wrench light turns on it's recorded and is stored as a specific code ! They told me at first that I should bring it in when the wrench light is on , then I retorted by saying HOW IN THE HELL DO YOU WANT ME TOO BRING IT IN IF IT ONLY GOES 5MPH ! I'M NOT DAMAGING MY VEHICLE !
I actually had my son put a brand new one on and then it's still having problems but I had it put on a scope and they're saying transmission like a bunch of words sensors came up and he says I knew it need a whole new transmission it didn't sound right to me because that's not the way it was acting once I wrench light was off at shifted fine
I put a brand new throttle on also and it didn’t stop the problem... also changed an o2 sensor and a cam sensor and also a map sensor still the same problem happens.... I don’t think it’s the trans because wen the wrench light is not on everything is fine
The same thing happens to my explorer 2006 v8 4x4 and after you go alot of the ligths star to turn on what the hell ford cant find the problem really first they said body troddle, them speed sensor and then pedal now they saying its the abs WTF what should I do
My 2010 Ford Escape did the same damn thing and it happens like 2-5 times a Day. I took my car in for service, i paid $80 because the mechanic said it was the throttle body. Mind you, before i went there, i stop by at Autozone to check the engine light. It came back with fuel pump issue. Code P455 P457. After the auto service fix my car, it was about 4 miles, it work perfectly fine... As i enter into the freeway, wrench light screaaaaam again. 😭 i can barely run 5 mph. Turn off, on, it went back to normal. I do thing its really the fuel hose, something to do with gas. I spend $229 today. I'll take it in to fix my EVAP or replace the fuel hose and we'll see if it puts an end to this.
Tevita Tu'ifua what happened? currently having this issue with my car but it doesn’t stall out. removed and cleaned the throttle body but still same problem and symptoms
Hey Whitswit, Mine is fixed, First they clean the throttl body, I brought my car home, When i entered the Freeway, the same thing happen, however this time, it was a lot better than before. for instance, Red lights, I cant even gas my car like everyone else but after they clean it, i was able to.... I just cant run over 60mph,.... I took it back, He said my car need a NEW throttle body....So when i brought back my car this time, No issue happened lately. *New Throttle Body solve this issue for me.*
I took my mustang to autozone and I got EVAP very small leak detected error P0456. I still didn’t do anything about it but my issue is that when it happens I can’t accelerate at all. The pedal just stops responding unlike others who say they can move slow. So after u got it cleaned the same issue happened after u reached 60mph or the car didn’t let u accelerate past 60? I’m very worried. You think I should try to clean the throttle first or just get a new one right away?
@@zaidmeqbel5465 mine is doing the same thing i asked a few good friends and they tell me its a throttle body. Its not letting a enough air in and to much gas or vice versa. So ill be getting a new throttle body today as well as the purge canister.
I HAVE 2013 FORD TAURUS MY CAR JUST DID THIS ...YELLOW RANCH CAME ON ...BUT CAR CRUNK BACK UP LIKE NORMAL...SO HOW OFTEN DOES THIS OCCUR ...WEEKLY, DAILY
If the wrench light comes on it’s a powertrain malfunction. You will experience severe issues with engine power if that light comes on. So essentially you’ll barely be able to move.
Mine just did the same thing as I was trying to leave my house. Is it a recall? I took it to ford not too long ago because the wheel locked up on me while driving.
This is happening in my 2014 ford fusion so if I turn the car off and turn it back on I should be fine? And I tried revving my engine after I turned it on and off and still made a different noise
yes my 2014 ford fusion doing this ONLY when im on the highway..i pull off ... turn engine off and restart and its all good ..going to dealership on tuesday
WOW so many different explanations, it's obvious this wrench light indicates a whole world of different issues. I have a 2008 Ford Escape V-6 and I bought it with the wrench light on for $1000 thought it was a good deal ( AND IT IS ) so just need to get it fixed. With my truck it seems to be the shifting is the issue , it doesn't shift properly from stop and go but once I'm over 50km's an hour it drives like a normal vehicle easily reaching 120km or more even up the steepest mountains here in British Columbia Canada. hmmmmmmm something so small can cause so much grief to all of us lol.. GOOD LUCK EVERYONE
@@PreetSingh-ji7ey Hey Preet.. I'm on the Island right but I live up over the Coquihalla but I haven't had my truck fixed yet because it drives fine and personally it doesn't concern me all that much. I've very much mechanically inclined so myself and another mechanic friend have determined it's not going to hurt my truck driving it this way... Chalk it up to being too busy but more likel procrastination hahahaha. Hope you don't have any issue's.
Katie they will be covered for the electric throttle body if that is the problem . My Escape never really lunged into gear but if it happens again I would take it in and demand they change out the ETB , then it adds another 10 year warranty for the electric throttle body. carlos16822@att.net if you need help 😉
I had this issue on Friday the wrench light came on with the AWD off light. It crawled at almost a nonexistent speed. It's sitting at the mechanics shop now and he is stumped due to it not having any codes stored. I'm hoping he can figure it out. I don't even want to think about taking it to Ford 🙄
I do the same thing it does it everytime i drive it and come to a complete stop. The car goes into like a limp mode and if i turn it of and back on it goes away and drives fine unless its hot then it acts like it is slipping until you get up to atleast 5 or 10 mph and it will grab and drive fine again so confused it has got me stumped
@@dylwillonewheel7614 My Freestyle has been doing the same thing. At first I would turn it off and on and problem solved. Now the light will stay on until I park for a long time, like overnight. On cold days I can drive a lot and the light will not come on, unless I am in heavy traffic or long traffic lights. This tells me that temperature has something to do with it, even if the engine temperature shows normal levels at all times. In any event, the moment that light comes on the car starts to act up, with jerky motion and high RPM required for 35 MPH (2,000 RPM). It has some other issues but I keep driving it.
@@dylwillonewheel7614, by the way, I changed the throttle body, the EGR valve and the accelerator pedal. I don`t know what else to change. Maybe the car.
I have an 08 mustang GT it just started doing this I start the car and at idle the wrench will never pop up but as soon as I shift into first gear and start moving it comes on and Boggs the car down but since mines a manual I can drive it around I can still do about 80 on the highway still but it’s just A LOT slower does anyone know if this is a serious issue or if it’s just some stupid sensor that’s causing the computer in the car to have a panic attack
I have a 2020 mustang gt with manual transmission and it came on @ 14500 miles. I took it to dealer but it went off . I still had them check it but nothing came up..
I need help! I have a Ford Fusion 2006, this happened to me as I was getting on the freeway in my city. I was doing about 70 and then the vehicle jolted and almost stopped running and my car slipped on ice and swerved into the right lane where a semi was. I was close to hitting it, I'm still pretty shaken up. What can be done? Would ford be responsible?
@@Anna8765 There might be couple reasons for this . 1- If you have ford hybrid most probably it is mecs coolant pump. 110 bucks under the engine easy to fix. 2- If your vehicle is not hybrid it is still coolant pump but you need to check your coolant level first. 3- It might be throttle body. If it is throttle body DONT TRY TO CLEAN AND REPLACE by yourself because you will need expensive scan tool to recalibration. I am writing this and in las t 2 hours it happened to me 3 times. My car is 2012 lincoln mkz hybrid. My car is 256 000 miles. Btw I still can drive more than 40 miles between restarts. I ordered the part and will change asap
For me I am having the same issue, I have found that if I go over any bumps in the road the check engine and wrench lights come on and I lose all power and can only creep very slowly. With further investigation I realized if I jiggle the cables going to my throttle body I can recreate the problem every time. I have been fighting this battle for months with a dealership, first I paid 800 for new throttle body, I had that refunded now the second dealership tells me it was my PCM, changed that 1200 dollars, still same thing happens. I let them know what I found and they refuse to refund me my 1200 for there shitty service. So a lot of times its just in the connection and nothing actually wrong with the car itself. Hope this helps. Ps if anyone can make a video of how to fix this it would be great.
My car has been at the mechanic all week trying to figure out what was wrong. They think it is the cooling pump for the catalytic converter. He says my car acts like it has California emissions. I am in michigan. He says this car has a great engine and he has never seen this before. 07 fusion
take it to your dealer make sure you record it like I did and if they say you need to bring it in with the check engine light on that's b.s. cuz the computer will keep a record of engine faults plus you have it on video. All Escapes from 2008 thus 2014 should be covered for this at no charge
Hi, do you have any info that all Escapes from 2008-2014 should be covered? My 2008 Escape's wrench light just went on tonight and it kind of lunged into gear when I accelerated.
Thank you for sharing The 2014- 2016 Ford products Stalling /Loss of Power Throttle Body seems to be a consistent issue in the Ford Escapes, Flex's, Explorers 2015 to present, and other ford products. These safety issues include, but are not limited to: sudden jolting; sudden stalling; sudden deceleration; sudden loss of power without warning; vehicle going into limp mode; no throttle response, and transmission failing to stay in park. When these dangerous safety issues occur, it appears that consumers claim that the check engine light, air bag light or a light in the shape of a wrench illuminates in the gauge cluster of affected 2016 Ford Explorers. This can be a major issue especially for officers responding to an emergency. Please look for us on facebook and comment your experience to Alert other consumers about this issue. For more information on these claims contact us at THEALERTCONSUMER@gmail.com website coming soon. facebook.com/TheAlertConsumer/
I have a 2009 ford focus ses and my wrench light is on an engine light and when you turn car off then back on its gone but comes right back. I put a new throttle body I bought a new air flow sensor. An still same problem
@@dylwillonewheel7614 ditto for me. Just recently started. Car runs rough when putting into gear after wrench comes on. If i put car back into park and shut off/turn back on, it then runs ok. Might try resetting the cars computer using the technique mentioned by Fordtechmakuloco on CZcams....to relearn calibration. Might also try removing throttle body unit and cleaning it. Hoping this isn't an actual transmission issue......car doesn't seem to have obvious transmission issues.
There might be couple reasons for this . 1- If you have ford hybrid most probably it is mecs coolant pump. 110 bucks under the engine easy to fix. 2- If your vehicle is not hybrid it is still coolant pump but you need to check your coolant level first. 3- It might be throttle body. If it is throttle body DONT TRY TO CLEAN AND REPLACE by yourself because you will need expensive scan tool to recalibration. I am writing this and in las t 2 hours it happened to me 3 times. My car is 2012 lincoln mkz hybrid. My car is 256 000 miles. Btw I still can drive more than 40 miles between restarts. I ordered the part and will change asap
Crankshaft position sensor 20ish dollars replace it then drive around with ac on but do stop and go city like driving 20ish mph nothing fast like for ten minutes to let the brain relearn the new part then your good to go
Karen Bauer Sinnen Yes under the customer satisfaction program, if it's the electric throttle body problem , they will replace it at no cost plus extend the warrenty for that also . Make sure you call Ford and ask them about it @ 1 800 392 3673 , Google it also 😊
Carlos Romo thanks for the reply. my car is the Ford 500 it does the same thing except it stays like that won't change when I turn off the car. I'm.hopimg it's the throttle body
This is exactly what happens with my 2006 for 500 I took it to the garage and they said it's my transmission what was the outcome of your car please respond
This is happening to my 2008 Ford fusion..when the wrench light comes on it still drives but idles and doesn't switch gears and wen I turn off the car and turn it back on the wrench light comes off and it drives perfectly fine..does anyone know what I need to do and how much it will cost ?
So....I'm at the dealer for a recall. Asked about customer satisfaction program...she said it's for the intermittent stuck in first gear issue. Which I've had
Ive owned ford for over 15 years and been surrounded by fords for 30 years. ford has had terrible electronics since 1993 era and the more electronics you throw at it the shittier they become. Ive had new f150s, new escapes, new ford five hundreds several rangers. Only great vehicle ford ever made was the 01-06 or so f250 with the 7.3l diesel. my 2012 f150 is not worth the tires it sits on. if i could only afford a tundra, ford has cheap baseline vehicles but after experiencing same issues in sedans to trucks to suvs its a common problem. I blame the investors sucking the funds out of the company they need to pull out of the stock market entirely and frankly i hope everyone invested in them loses their retirement! Your not the only one anyway. too bad ford and gM own NHSI and DOE who commonly discredit smaller manufactures as not having good enough emissions and not safe enough to drive, yet fords throttle body is responsible for several deaths including a few kids hit by their own parents car that rev'ed out of control forward. Go ford like a real american company kills and abuses its own customers.
Sorry guys. I replaced the Brake ABS module, Transmision module, rebuilt the Transmision and all brake, ABS, Traction control lights still on but car is drivable since rebuilding Tranny. Only had 50k miles on it so let’s see how it goes. Very disappointed in Ford and the quality of this.
I have 2016 Explorer with 4800 mile. orange wrench and engine light came on. could only travel at idle speed. Ford not very responsive. clised gor 4th. no one would help. "bring it in 5 july", today is the 2nd.
I noticed alot of common comments but really know defined answer to this issue. So I went through the comments and wrote down the most brought up issue wich was the throttle body. Then started watching videos based on that. I took it to autozone to confirm. Came back as throttle body sensor. So 2 choices. Buy a new throttle buddy $350 lowest price for my vehicle or clean the one I have. I bought some throttle body cleaner and removed that part. It was totally black. Sprayed and wiped twice and it was shiny gold. Connected back to vehicle and the check engine light is gone. Been driving most of the day off and on and still no tool light no check engine. This fix cost me less than $10( cost of throttle body cleaner) Hope this helps. My situation was pretty much the same as the person that uploaded this video.
Thanks for the info!! I had that problem today…
Just had this problem Thanks for the tip
Just happen to me
Thank you. I side hustle as a delivery driver and until I get this fixed....
I appreciate your research and sharing
Fingers crossed, prayers up!!
I think the reason for the conflicting comments is that it is the "check engine" light. I can be coming on for a multitude of reasons. I have a 2010 Fusion Hybrid and the light came on while in Florida. Stayed on the entire week. Fueld at the midpoint in GA. Never came on again for years. Then one day driving at high speed it came on. Went off later. Again a couple of years later, it came on again. It's always in high humidity and heat! My problem does not effect power and always the hybrid wreck comes on first, followed by the gas engine wrench.
This happened to me on my 2008 Edge, brought it to the dealer, this is caused by two sensors in the power train which need to be replaced would cost me $750 to fix, I haven't done the repair yet. This really sucks, I am finding out this problem is very common now in Ford vehicles. We should get a class action lawsuit started.
it happens to me too so count on me for the complain
This doesn't happen to all. It has to be 09 and above. My mom has a 2010 Escape and this has happened to her. I have a 08 but never heard of this.
55dbau yes we really need to get a lawsuit started. Same thing happened to my 2007 ford e250??
Shitt is happening to me right now 🤬
I just bought a 2009 escape hybrid. I’m getting this wrench light also. What 2 sensors were bad? Thanks.
Be persistent it should be covered under the powertrain warranty plus you could call Ford and ask for the customer satisfaction program a representative there will give you a claim number and you can follow up with them about the repair
Did they tell you what caused it and what u have to replace ?
@@nathatmed6484 they never admitted to a failure of the electric throttle body much less a recall, there thing is that we have to run a diagnostics check first then they will replace it at no cost to you provided it is still under warranty for the powertrain. I would still follow the steps above and try to take some video of the problem happening so you can have some ammo on your side also look on the web and try to find some corresponding info from others like us. Good luck to you, I can promptly holler back too 😎
Did they tell you how long the power train warranty is for? And does it cover it? I'm in el paso, any specific ford you took it to? Sorry for all the questions, just happened today
I have a 2006 ford fivehundred that has been doing the same thing , turns out the wiring harness on this model and the 2005 and 2007 runs right across the top of the enging. Over the years the constant heat from the engine had melted wire into in numerous spots and they were touching. It's why it does it going down the road instead of starting that way. Because bumps and holes in the road or whatever tmcan make those wires not touch and when you restart it itll crank up normal. But drive a mile down the road and hit a hole just right and those wires will touch together again and put it back into limp mode.
Does the 06 freestar have same
So I have a 2005 Ford Five Hundred that is randomly doing the exact same thing "engine safe mode" with a wrench. Pulled Codes P2104 Forced Throttle and P2112 Throttle stuck closed so I replaced the throttle body and still doing the same thing. I'm thinking this is also a wiring short or ground that's causing this intermittent issue. I'll check the wire harness that you mentioned to see if it's heat damaged by engine or friction. Thanks for your post!!
@tonyvella3242 have you had anymore problems since you replaced the throttle body?
This just happened to me yesterday and I barely made it home. I have not restarted it yet but I hope it is no problem and it will work when I use it next...ugh. I only have 55, 000 miles on my taurus 2008.
I have a ford transit connect 2013 it comes on when I lower the stearing wheel to the low level and lock it. it doesn't affect the engine running.
2009 Mazda Tribute happens alot and check engine light turned on with the code that the Throddle is stuck open. Cleaned ot with a throddle cleaner worked fine for a week and now its shuting down again. Do i need a whole new ETB or just a new sensor dor the air mass flow
I'll never get another Ford
Wowwwww. El chuco town.... Miss it
This just happened in our 2010 ford escape. We bought it from someone last year. Do you think it would be covered under warranty?
My f250 6.0 powerstroke does this too and I don't have the 5k to fix the problem. Just got the truck "as is' 3 months ago, it's a fking disaster, now I'm stuck in a loan. I feel your pain brother.
This may possibly be an oil cooler issue. There is currently an investigation on behalf of consumers who purchased Dorman oil cooler kits for their 2003 - 2010 6.0L Ford Diesel Trucks to replace the factory Ford Oil Cooler. Dorman Oil Coolers are non-OEM (aka aftermarket) oil coolers sold at stores such as NAPA, Advance Auto Parts, Auto Zone and more.
The Ford 6.0L Diesel Dorman Oil Cooler kit (part number 904-228) is sold for use in Ford Diesel vehicles made from 2003-2010. It appears that O-rings and gaskets within the kit are believed to deteriorate into small particles (sometimes green or yellow in color) that spread throughout the Ford diesel engine, causing expensive damage.
If you purchased a Dorman Oil Cooler, had it installed in your Ford 6.0 Please contact us at Thealertconsumer@gmail.com and tell us your experience. Website is under construction. Find us on facebook @thealertconsumer
Throttle body. Make sure you recalibrate the new one.
I have the Ford Edge 2013, Same thing... It was so dangerous. FORD should do a recall of all vehicles that has a problem with the Electronic Throttle Body. Be careful if you have a Ford!!
Before changing the Throttle Body clean it with a Throttle Body cleaner, that could save you $500, and clean the Mass Air Flow sensor (MAF) with a MAF cleaner.
@@robertzamb that what I said I was going to do. A mechanic here in Houston Texas told me to contact a Ford dealer to find out if it was a recall on this problem
It's a recall on my mother 2010 Escape
2013 Ford Fusion no issues at all 194,000 miles
I have the 2013 fusion too im having this same issue. It stopped on me last week wouldn't turn back on. I had it towed to the dealer
I had this problem and had to change the throttle body and now its fine
I’m having the same problem with my 2012 Ford Fiesta. What should I start replacing first.?
I have a 2014 Ford Edge and the same thing happened to me. The Dealer just called and told me it waa the Throttle body and it will coat $490 to fix. I have only had the car 2 years and a couple months!! I called Ford customer service and of course they did nothing because there is not a recall for my vehicle
Replace TPS or try cleaning it ... N just replace cople sensors .. in that area
Anyone who have this problem if you have these 2 problems if you brake and it takes time to slow down or if you floor the gas pedal and the response hesitate before the wrech light come it’s your Acceleration position pedal sensor. Most people thing it’s the throttle body but the pedal tells the throttle body how much to open or close. If you have a electrical throttle body. Hope this helps had the same problem with my ford mustang
This just happened to me to today in my ford edge and it was very scary considering this was the first time.
Same here. Ford is BS
I have a Ford Fusion 2006, this happened to me as I was getting on the freeway in my city. I was doing about 70 and then the vehicle jolted and almost stopped running and my car slipped on ice and swerved into the right lane where a semi was. I was close to hitting it, I'm still pretty shaken up. What can be done? What happened with your vehicle? I read somewhere that this is a safety issue and ford can get a lawsuit filed if they don't fix it???
Its is most likely the Electronic Throttle body. Had the same problem in my 06 Milan and that was the issue. Took me about an hour to change.
Cusheena Mcrae hi. Where is the etb located in the car?
Yes plz it would be really helpfull since I'm in the same spot
@@jaeescobar3106 did you figure it out mine just started
i have 07 milan its doing the same exact thing...wrench light then going in and out of gears high revs and jerking motion....is yours still running good? , and was there a recall for the throttle body?...there is a recall for the airbags just so u know...they can kill u w metal shrapnel inside them.
I have the same issue right now with my 2010 Fusion everything is cool when the wrench is not on the dash but as soon as it pops up it just stalls like you don't get no speed it'll barely let you move 10 miles an hour but when I took it to AutoZone they said it was a throttle body and this purge valve I changed both of those and it seemed the car was running fine and then it started up again. and it sucks because I have to be in work tomorrow and today is Sunday so I couldn't take it to no shop because there is no mechanics and after I get this situated I'm probably pretty much done with Ford
Did you by any chance get it fixed?? I'm having the same issues, and it's stressing me out. Mine is a 2014 fusion. 😞😞
if I were you I would take it in right away , everyone out there will be glad to know the even if you have a 2009 like my Escape the Electronic Throttle Body will be extended to another 10 years so in my case it is still covered till 2019 , don't be fooled this is a bigger problem than Ford would like to admit, the reason it is not a all out FACTORY RECALL is because Ford got a jump on it and layed it out as a customer service /safety program , in your case 2016 should be covered till 2026
I have a 2007 ford five hundred that's having the same issue. I purchased my car like 4 years ago from Carmart. So will I be able to get it fixed under warranty for free?
What did you find out, and what did you do for your issue?
Just happened to me, 2013 Taurus. When I hit the gas it wouldn't move, let off and it. Coasted.
How did you fix it?
I had this issue one day. It was due to a blown ABS fuse. I replaced it and the light went off.
Did you figure out what the problem was ?
Same thing just happened with my mustang yesterday, but when shutting off and turning back it was still the same.
Did u ever find the problem?
Had the same issue. Sent my 2011 fusion today to the dealer and they changed the ETB for free.
How many miles you have when it happened?
@@valeriequintana906 less than 180 000km
my saturn view did that so at a light i had to put in low to take off and acouple mile it would run knew again
I have not had any problems with my 08 Ford Taurus. It has 161,000 miles on it. Still working good
my truck is doing the same shit
i have the same problem., whats the issue
I have a 2016 explorer and it happened twice today. Scary!!!
I got the same problem in a explorer 2016.
How you solved it ?
How did you fix the explorer
Its your ignition coils they are bad, or cracked Giving it a bad signal to transmission, if the transmission is doing weird stuff, and the wrench light comes on and the the traction control light the coils are the problem
So, did you find out what the problem was? Mine just came on Saturday and my car slowed down alot. I cut it off for a few minutes then start the car up and no wrench. Please let me know the diagnosis!
Did you fix it
my old man Car Started to do that it a ford five hundred
The wrench 🔧 light is a tune up spark plugs and coils you have to use the Oem plugs and coils (Motorcraft)
After time the aftermarket plugs cause faluty combustion and the car goes into Limp mode. A bad injector can cause this as well for the most part just add Lucas fuel treatment after changing the plugs and coils.
Not on all vehicles, ford's its a trans issue/AWD issue
Not on this one
0:55 you think this is a problem while driving on the fwy? 😂
tonight while driving my 2008 ford fusion home it happened to me , i have noticed in the past a intermitenet rarely engins stall and refire , suddenly the engine drops to 0 rpm then everything back to normal , like 10 random times during the last 2 years , and now tonight the wrench lights up and every 10 minutes complete loss of power and rpm drop to 0 then sudenly everyting is ok , only 53,000 miles , having a ford sucks , i will never have another ford ever
I have a 2007 F150 what does that really mean when you get that cause I did the same as this guy I would love to know is it a problem or something you don’t need to worry about
It happend to me today just that way, turned it off then on again!
I have a 2008 focus sel and it came on but I could drive at normal operating speed
Hyraj next door neighbor I got that happening to my Ford Flex but like you said my truck driving normal with the light on
that's a damm shame it's still under factory warranty, don't give up ! Too bad it's 4th of July weekend , but that's bull shit don't give every time the wrench light turns on it's recorded and is stored as a specific code ! They told me at first that I should bring it in when the wrench light is on , then I retorted by saying HOW IN THE HELL DO YOU WANT ME TOO BRING IT IN IF IT ONLY GOES 5MPH ! I'M NOT DAMAGING MY VEHICLE !
It's the electric throttle body, that's the problem .
I actually had my son put a brand new one on and then it's still having problems but I had it put on a scope and they're saying transmission like a bunch of words sensors came up and he says I knew it need a whole new transmission it didn't sound right to me because that's not the way it was acting once I wrench light was off at shifted fine
I put a brand new throttle on also and it didn’t stop the problem... also changed an o2 sensor and a cam sensor and also a map sensor still the same problem happens.... I don’t think it’s the trans because wen the wrench light is not on everything is fine
@@flyboydj719did you ever find the issue I'm going through the same thing
@@juanbadillo1373 you found out what was going on with yours
The same thing happens to my explorer 2006 v8 4x4 and after you go alot of the ligths star to turn on what the hell ford cant find the problem really first they said body troddle, them speed sensor and then pedal now they saying its the abs WTF what should I do
My 2010 Ford Escape did the same damn thing and it happens like 2-5 times a Day. I took my car in for service, i paid $80 because the mechanic said it was the throttle body. Mind you, before i went there, i stop by at Autozone to check the engine light. It came back with fuel pump issue. Code P455 P457. After the auto service fix my car, it was about 4 miles, it work perfectly fine... As i enter into the freeway, wrench light screaaaaam again. 😭 i can barely run 5 mph. Turn off, on, it went back to normal. I do thing its really the fuel hose, something to do with gas. I spend $229 today. I'll take it in to fix my EVAP or replace the fuel hose and we'll see if it puts an end to this.
Tevita Tu'ifua what happened? currently having this issue with my car but it doesn’t stall out. removed and cleaned the throttle body but still same problem and symptoms
Hey Whitswit,
Mine is fixed, First they clean the throttl body, I brought my car home, When i entered the Freeway, the same thing happen, however this time, it was a lot better than before.
for instance, Red lights, I cant even gas my car like everyone else but after they clean it, i was able to.... I just cant run over 60mph,....
I took it back, He said my car need a NEW throttle body....So when i brought back my car this time, No issue happened lately.
*New Throttle Body solve this issue for me.*
Tevita Tu'ifua thank you!
I took my mustang to autozone and I got EVAP very small leak detected error P0456. I still didn’t do anything about it but my issue is that when it happens I can’t accelerate at all. The pedal just stops responding unlike others who say they can move slow. So after u got it cleaned the same issue happened after u reached 60mph or the car didn’t let u accelerate past 60? I’m very worried. You think I should try to clean the throttle first or just get a new one right away?
@@zaidmeqbel5465 mine is doing the same thing i asked a few good friends and they tell me its a throttle body. Its not letting a enough air in and to much gas or vice versa. So ill be getting a new throttle body today as well as the purge canister.
my ford escape has a problem slowing down it will some time drop really hard into gear anyone know if this is a problem
Check your fluid if it's a sealed transmission if not check the pressure control solenoid pack
Could be your MAP sensor.
I HAVE 2013 FORD TAURUS MY CAR JUST DID THIS ...YELLOW RANCH CAME ON ...BUT CAR CRUNK BACK UP LIKE NORMAL...SO HOW OFTEN DOES THIS OCCUR ...WEEKLY, DAILY
Clean the Throttle Body, that could be the cause.
If the wrench light comes on it’s a powertrain malfunction. You will experience severe issues with engine power if that light comes on. So essentially you’ll barely be able to move.
Just bought a mkz, got the wrench, but car running fine, whats causing the light.
@@vracerv what was wrong with yours?
My car has the light but all the power still there its an 09 ford fusion
did it happen again man?
Mine just did the same thing as I was trying to leave my house. Is it a recall? I took it to ford not too long ago because the wheel locked up on me while driving.
Viviana Enamorado my 2013 Ford 150 is doing the same thing.
the when lock up thing though.
Does anyone know what causes that because I've been having the same problem with my 2008 Ford expedition
2009
I have a 2006 tool light come on and off sometimes
This is happening in my 2014 ford fusion so if I turn the car off and turn it back on I should be fine? And I tried revving my engine after I turned it on and off and still made a different noise
yes my 2014 ford fusion doing this ONLY when im on the highway..i pull off ... turn engine off and restart and its all good ..going to dealership on tuesday
@@tonylobin5749 hey it was the transmission and it cost 4 to 6g to fix I'd get a new rid or fix it if you have enough
@@alphacloak1822 hey, what was the transmission problem specifically?
Hello this is exactly what happens with mine. Did you find the cause of your problem?
Did you find the problem ? Happening to me now
Fuze #47 popped and caused this for my 08 mustang replaced fuze and all problems went away
WOW so many different explanations, it's obvious this wrench light indicates a whole world of different issues.
I have a 2008 Ford Escape V-6 and I bought it with the wrench light on for $1000 thought it was a good deal ( AND IT IS ) so just need to get it fixed.
With my truck it seems to be the shifting is the issue , it doesn't shift properly from stop and go but once I'm over 50km's an hour it drives like a normal vehicle easily reaching 120km or more even up the steepest mountains here in British Columbia Canada.
hmmmmmmm something so small can cause so much grief to all of us lol.. GOOD LUCK EVERYONE
I have the same problem . And in Vancouver BC .. did you gets yours fixed if so much parts and labour thanks
@@PreetSingh-ji7ey Hey Preet.. I'm on the Island right but I live up over the Coquihalla but I haven't had my truck fixed yet because it drives fine and personally it doesn't concern me all that much. I've very much mechanically inclined so myself and another mechanic friend have determined it's not going to hurt my truck driving it this way... Chalk it up to being too busy but more likel procrastination hahahaha.
Hope you don't have any issue's.
I have a 2006 explorer and the same thing is happening to me
What was the problem and how you fix it? I have the same problem with my Sport Trac now
Katie they will be covered for the electric throttle body if that is the problem . My Escape never really lunged into gear but if it happens again I would take it in and demand they change out the ETB , then it adds another 10 year warranty for the electric throttle body. carlos16822@att.net if you need help 😉
Yoooo I have a 2006 you thinknits still covered
@@mayhemgaming4297 no harm in trying
I had this issue on Friday the wrench light came on with the AWD off light. It crawled at almost a nonexistent speed. It's sitting at the mechanics shop now and he is stumped due to it not having any codes stored. I'm hoping he can figure it out. I don't even want to think about taking it to Ford 🙄
Any update ?
@@zykerahaynes4253 Throttle Body
Bronwyn Rice how much did it cost for labor
@@zykerahaynes4253 think it was like $100
Bronwyn Rice wow took my car to 2 mechanics paid 150$’ to find the issue and still can’t find the problem
I changed the oil, hasn't came on since..
Hey mine did the same I turned it of and on then went away what did you do afterwards?
I do the same thing it does it everytime i drive it and come to a complete stop. The car goes into like a limp mode and if i turn it of and back on it goes away and drives fine unless its hot then it acts like it is slipping until you get up to atleast 5 or 10 mph and it will grab and drive fine again so confused it has got me stumped
@@dylwillonewheel7614 My Freestyle has been doing the same thing. At first I would turn it off and on and problem solved. Now the light will stay on until I park for a long time, like overnight.
On cold days I can drive a lot and the light will not come on, unless I am in heavy traffic or long traffic lights. This tells me that temperature has something to do with it, even if the engine temperature shows normal levels at all times.
In any event, the moment that light comes on the car starts to act up, with jerky motion and high RPM required for 35 MPH (2,000 RPM). It has some other issues but I keep driving it.
@@dylwillonewheel7614, by the way, I changed the throttle body, the EGR valve and the accelerator pedal. I don`t know what else to change. Maybe the car.
I have an 08 mustang GT it just started doing this I start the car and at idle the wrench will never pop up but as soon as I shift into first gear and start moving it comes on and Boggs the car down but since mines a manual I can drive it around I can still do about 80 on the highway still but it’s just A LOT slower does anyone know if this is a serious issue or if it’s just some stupid sensor that’s causing the computer in the car to have a panic attack
I have a 2020 mustang gt with manual transmission and it came on @ 14500 miles. I took it to dealer but it went off . I still had them check it but nothing came up..
I need help! I have a Ford Fusion 2006, this happened to me as I was getting on the freeway in my city. I was doing about 70 and then the vehicle jolted and almost stopped running and my car slipped on ice and swerved into the right lane where a semi was. I was close to hitting it, I'm still pretty shaken up. What can be done? Would ford be responsible?
Is it hybrid ?
omer bayrak no
@@Anna8765 There might be couple reasons for this .
1- If you have ford hybrid most probably it is mecs coolant pump. 110 bucks under the engine easy to fix.
2- If your vehicle is not hybrid it is still coolant pump but you need to check your coolant level first.
3- It might be throttle body. If it is throttle body DONT TRY TO CLEAN AND REPLACE by yourself because you will need expensive scan tool to recalibration.
I am writing this and in las t 2 hours it happened to me 3 times. My car is 2012 lincoln mkz hybrid. My car is 256 000 miles. Btw I still can drive more than 40 miles between restarts.
I ordered the part and will change asap
omer bayrak not a hybrid must be the throttle
Mines is jumping parking it till I can get a maunal check up
put in low and it will move faster
i tried that. didn't work for me.
For me I am having the same issue, I have found that if I go over any bumps in the road the check engine and wrench lights come on and I lose all power and can only creep very slowly. With further investigation I realized if I jiggle the cables going to my throttle body I can recreate the problem every time. I have been fighting this battle for months with a dealership, first I paid 800 for new throttle body, I had that refunded now the second dealership tells me it was my PCM, changed that 1200 dollars, still same thing happens. I let them know what I found and they refuse to refund me my 1200 for there shitty service. So a lot of times its just in the connection and nothing actually wrong with the car itself. Hope this helps. Ps if anyone can make a video of how to fix this it would be great.
great info man thank you
I start having the same problem with my ford fusion STD 2007 and this sucks
My car has been at the mechanic all week trying to figure out what was wrong. They think it is the cooling pump for the catalytic converter. He says my car acts like it has California emissions. I am in michigan. He says this car has a great engine and he has never seen this before. 07 fusion
Did you ever figure it out I have the same Problem with mine I change the part for the code but it still does the same thing
How did u fix it?
Thats weird hey,hmmm,must be a ford wiring issue somewhere
what year and what kind of truck is it
915/329/6330 text me , that would be easier I think ,pleasssssssssssse 💆
So what do u have to do about that? Cuz it happends to me all the time n i still cant find help
@@thealertconsumer1145 I have the same problem in a explorer 2016
How can I solve it ?
I have a 2012 n the wrench light comes on and my car shakes and does exactly that
take it to your dealer make sure you record it like I did and if they say you need to bring it in with the check engine light on that's b.s. cuz the computer will keep a record of engine faults plus you have it on video. All Escapes from 2008 thus 2014 should be covered for this at no charge
Hi, do you have any info that all Escapes from 2008-2014 should be covered? My 2008 Escape's wrench light just went on tonight and it kind of lunged into gear when I accelerated.
Thank you for sharing The 2014- 2016 Ford products Stalling /Loss of Power Throttle Body seems to be a consistent issue in the Ford Escapes, Flex's, Explorers 2015 to present, and other ford products. These safety issues include, but are not limited to: sudden jolting; sudden stalling; sudden deceleration; sudden loss of power without warning; vehicle going into limp mode; no throttle response, and transmission failing to stay in park. When these dangerous safety issues occur, it appears that consumers claim that the check engine light, air bag light or a light in the shape of a wrench illuminates in the gauge cluster of affected 2016 Ford Explorers. This can be a major issue especially for officers responding to an emergency.
Please look for us on facebook and comment your experience to Alert other consumers about this issue.
For more information on these claims contact us at THEALERTCONSUMER@gmail.com
website coming soon.
facebook.com/TheAlertConsumer/
I have a 2009 ford focus ses and my wrench light is on an engine light and when you turn car off then back on its gone but comes right back. I put a new throttle body I bought a new air flow sensor. An still same problem
Same here
@@dylwillonewheel7614 ditto for me. Just recently started. Car runs rough when putting into gear after wrench comes on. If i put car back into park and shut off/turn back on, it then runs ok. Might try resetting the cars computer using the technique mentioned by Fordtechmakuloco on CZcams....to relearn calibration. Might also try removing throttle body unit and cleaning it. Hoping this isn't an actual transmission issue......car doesn't seem to have obvious transmission issues.
There might be couple reasons for this .
1- If you have ford hybrid most probably it is mecs coolant pump. 110 bucks under the engine easy to fix.
2- If your vehicle is not hybrid it is still coolant pump but you need to check your coolant level first.
3- It might be throttle body. If it is throttle body DONT TRY TO CLEAN AND REPLACE by yourself because you will need expensive scan tool to recalibration.
I am writing this and in las t 2 hours it happened to me 3 times. My car is 2012 lincoln mkz hybrid. My car is 256 000 miles. Btw I still can drive more than 40 miles between restarts.
I ordered the part and will change asap
any updates?
Crankshaft position sensor 20ish dollars replace it then drive around with ac on but do stop and go city like driving 20ish mph nothing fast like for ten minutes to let the brain relearn the new part then your good to go
Did you ever found out the problem?,I had that problem today need help .
Did you find out??
This is happening to my 3 year old Ford Everest Titanium. Never buy Ford.
did you ever get it fixed?
Karen Bauer Sinnen Yes under the customer satisfaction program, if it's the electric throttle body problem , they will replace it at no cost plus extend the warrenty for that also . Make sure you call Ford and ask them about it @ 1 800 392 3673 , Google it also 😊
Carlos Romo thanks for the reply. my car is the Ford 500 it does the same thing except it stays like that won't change when I turn off the car. I'm.hopimg it's the throttle body
@@MrYandell49er what year is your? My mom escape is 2010 and she bought it the same year. She hardly have any miles on here.
@@slimsampy4764 2009 she can still take it
@@MrYandell49er I spoke with a Ford dealer today and it is a recall. So it's going in tomorrow morning and for another recall on the fuel flange
Mine is doing the same shit what is it??
Is this the same for a crown vic
Yes just happen to me today
It's just the TPS ..
This is exactly what happens with my 2006 for 500 I took it to the garage and they said it's my transmission what was the outcome of your car please respond
Brenda Mason ^
This is happening to my 2008 Ford fusion..when the wrench light comes on it still drives but idles and doesn't switch gears and wen I turn off the car and turn it back on the wrench light comes off and it drives perfectly fine..does anyone know what I need to do and how much it will cost ?
Did you figure anything out mine is doing the same
Its electrical gotta flush the memory from the car unplug the negative on the batterie there is a guy who shows how to do it on youtube
The throttle body electtrical are the probleme
My ford focus 2009 is doing the same thing and i have try my possible best to resolve no way
check your power train warrenty, most are 10 years, don't be fooled, question authority
Can you contact me. I'm having the same issue. 274-1698
So....I'm at the dealer for a recall.
Asked about customer satisfaction program...she said it's for the intermittent stuck in first gear issue. Which I've had
This happen to me
Ive owned ford for over 15 years and been surrounded by fords for 30 years. ford has had terrible electronics since 1993 era and the more electronics you throw at it the shittier they become. Ive had new f150s, new escapes, new ford five hundreds several rangers. Only great vehicle ford ever made was the 01-06 or so f250 with the 7.3l diesel. my 2012 f150 is not worth the tires it sits on. if i could only afford a tundra, ford has cheap baseline vehicles but after experiencing same issues in sedans to trucks to suvs its a common problem. I blame the investors sucking the funds out of the company they need to pull out of the stock market entirely and frankly i hope everyone invested in them loses their retirement! Your not the only one anyway. too bad ford and gM own NHSI and DOE who commonly discredit smaller manufactures as not having good enough emissions and not safe enough to drive, yet fords throttle body is responsible for several deaths including a few kids hit by their own parents car that rev'ed out of control forward. Go ford like a real american company kills and abuses its own customers.
My truck F150 2006 doing the same??
Clean the Throttle Body, that could be the cause.
did you find out the problem my 07 is doing it now
I have 06 F150....did you find the problem
My 2016 Explorer started doing the same thing last night. Have found anything on WTF is wrong with these fords??
Victor Jones have you found anything out?
I have the same problem
How you solved it?
I hate people that comment looking for answers, but they never come back to let people know how it was resolved.
Sorry guys. I replaced the Brake ABS module, Transmision module, rebuilt the Transmision and all brake, ABS, Traction control lights still on but car is drivable since rebuilding Tranny. Only had 50k miles on it so let’s see how it goes. Very disappointed in Ford and the quality of this.
I have 2016 Explorer with 4800 mile. orange wrench and engine light came on. could only travel at idle speed. Ford not very responsive. clised gor 4th. no one would help. "bring it in 5 july", today is the 2nd.
should say closed for 4th
Did you find out anything on what the cause/how do you fix it?