Comeback that NEVER Left! OIL SPILL! Volkswagen Jetta 2.5

Sdílet
Vložit
  • čas přidán 26. 07. 2022
  • How it all started HERE. Over Engineered Bolts! Four wheel brake job. Actuated Calipers. Volkswagen Jetta 2.5 • Over Engineered Bolts!...
    Check out my Merchandise (because I don't say MERCH) Store Below the video for Men's and Women's Apparel, MUGS and Stickers!
    rainmanraysrepairs.myspreadsh...
    Send support on Patreon, check out the bio: / rainmanraysrepairs
    Patreon is a "Tip Jar" I don't post much there, daily YT uploads are all that I can manage right now
    Amazon List, must have for any toolbox!
    ATD Tools 13782 10-Piece Triple Square Spline Bit Socket Set amzn.to/3RV2fUB
    Same as Matco. Mountain 5-Piece Metric Double Box Universal Spline Reversible Ratcheting Wrench Set; 8 mm - 18mm, 90 Tooth Design, Long, Flexible, Reversible; MTNRM6 amzn.to/3OJTRp2
    Mercedes BMW VW Wheel Stud Master Kit: amzn.to/3OszRaL
    Bahco "Frustrated" Pliers AWESOME tool! amzn.to/3IfDeOa
    Brake Caliper Compressor: amzn.to/3gQBuiB
    GearWrench Hose Clamp Pliers: Currently Unavailable
    My Camera Gear:
    Gopro Hero 8 amzn.to/3mPnpFA
    Gopro Hero 9 amzn.to/3EKDcM1
    Hero 8 Dual Charger amzn.to/3EId84c
    Flexible Camera Mount amzn.to/3Jywrk5
    As an Amazon Associate I earn from qualifying purchases. #commissionsearned.
    Also, I personally use or have used the products featured in my links and only recommended them if I feel they are of good quality.
    “All the videos, songs, images, and graphics used in the video belong to their respective owners and I or this channel does not claim any right over them.
    Copyright Disclaimer under section 107 of the Copyright Act of 1976, allowance is made for “fair use” for purposes such as criticism, comment, news reporting, teaching, scholarship, education and research. Fair use is a use permitted by copyright statute that might otherwise be infringing.”
  • Auta a dopravní prostředky

Komentáře • 1,1K

  • @oobaka1967
    @oobaka1967 Před rokem +148

    Anyone who puts an oil pan drain plug on that tight / cross threaded should be charged with vandalism.
    They are purposely damaging the vehicle.

    • @SmallKittyPaw
      @SmallKittyPaw Před rokem +16

      Anyone who produces shitty oil pans/plugs should be charged. It was so tight because it leaked. It probably was same chines crap shop bought for first time. And someone (probably owner) just keep tightening it

    • @Straight_White_Fatherly_Figure
      @Straight_White_Fatherly_Figure Před rokem +13

      @@SmallKittyPaw yeah i agree. With how often the oil needs to be drained, youd think manufacturers would at least make the threads of the pan a tougher metal than aluminum..

    • @IIGrayfoxII
      @IIGrayfoxII Před rokem +25

      People who go to quiklube places should lose their car and drivers license,
      These places are known for fucking shit up.
      They use the cheapest conventional oil, they will use it even if you pay extra for synthetic because you wont know
      They use teeneages who dont know how many ugga duggas to use on a sump bolt which is in the milli uggadugga range.
      They even cover up their mistakes.
      remember seeing a video where a quik lube place did not add oil, engine seized, the customer took it back to the shop, they added oil then said, you have a "Warranty" problem.
      When the engine was torn down, no oil in oil pump or oil filter.

    • @daveverdonschot7956
      @daveverdonschot7956 Před rokem +7

      I think VW wants you to replace the drain plug with a new one every time... I guess not everyone does that.

    • @theoldbigmoose
      @theoldbigmoose Před rokem +23

      GM does it right. No crush washer, but an O ring with controlled compression designed into the bolt. What a concept!

  • @jimgilbert6511
    @jimgilbert6511 Před rokem +16

    Ray don't ever feel bad about calling out inferior products, it helps people like me who work on their own vehicles to know which (and why) to avoid them.

  • @TheCaptainbeefylog
    @TheCaptainbeefylog Před rokem +166

    Hearing you mention evening out the torques when fitting the pan reminds me of a time I was with my wife and we were talking to a mechanic about getting some work done on her car. I watched one their guys putting a head back on an in-line 6 cyclinder engine and he just went "around the clock" with the rattle gun they use for the tyres. We left shortly after that and went to a different shop.

    • @XStuntManiac
      @XStuntManiac Před rokem +13

      Did he rattlegunned it with all the torque of the gun and went back to assembling the rest of the engine or he just threaded it in? You can actually thread stuff in with little to no torque in the end even with one of these.

    • @TheCaptainbeefylog
      @TheCaptainbeefylog Před rokem

      @@XStuntManiac Nah he went full hammer on it. I was surprised he didn't shear off a head bolt.

    • @XStuntManiac
      @XStuntManiac Před rokem +18

      @@TheCaptainbeefylog Fair enough, I'd walk away too.

    • @KazeHorse
      @KazeHorse Před rokem +28

      @@XStuntManiac broski don’t use any air or power tools for head bolts. Just ratchet then torque them per specs.
      It’s not an ‘it might be alright’ scenario - it’s a classic risk vs reward scenario.

    • @jaykellett2327
      @jaykellett2327 Před rokem +15

      Almost every mechanic knows you torque down an engine head in the proper sequence in a two step process. About 40% torque, then repeat to full torque.
      It ain't rocket science guys.

  • @Paolo0902
    @Paolo0902 Před rokem +6

    Dorman spare parts - enough said

  • @johnleinen7167
    @johnleinen7167 Před rokem +17

    Dorman, the king of the do over! I found one of those Snap-on lamps on the frame of a truck and it was coated with mud, probably was there a few years cleaned it and it charged back up and I use it to this day.

  • @jerrymoore7669
    @jerrymoore7669 Před rokem +136

    The fact that the bolt holes lined up was a miracle.

    • @jameslastname9171
      @jameslastname9171 Před rokem +4

      Seriously!
      Dorman has let me down so often

    • @charleshines1553
      @charleshines1553 Před rokem +6

      @@jameslastname9171 I don't buy any Dorman parts for my Passat. Unless it says made in Germany and is a good brand I don't want it! I also don't care for universal fluids with the exception of windshield washer fluid. Motor oil is different, a good German brand like Liqui Moly is fine. This next thing I am about to mention is not a Volkswagen only thing. That would be coolant, do not mix coolant types!! If you must top off coolant to make it home and can't find the right stuff, use water only (distilled very much preferred). If you mix some other type with the stuff in there it can for a jelly like substance and clog your radiator, heater core, and even cause overheating!!
      One other thing to watch out for is just because a coolant is the same color that doesn't guarantee it to be the same stuff!! For example both Toyota and Volkswagen have a pink coolant and they are both different even though they may look the same. That color is just a dye! They could just as easily make all coolants one color if they wanted to. It would be like the early days when there was just the green stuff we all may have seen before. I seriously doubt they would do a thing like that but that is all the color is, dye.

    • @MonkeyJedi99
      @MonkeyJedi99 Před rokem +3

      What is it with Volkswagen forcing mechanics to have a massive array of different tools to work on their cars?
      Are they allergic to hex bolts and nuts over in Germany?

    • @charleshines1553
      @charleshines1553 Před rokem +3

      @@MonkeyJedi99 They are just different that way. You will find triple square bolts on them too. If you ever encounter those DO NOT just use a Torx, that is one thing that will leave you with a ton of problems with those bolts!! It is also bad enough some of them would be really hard to get to so you really don't want to ruin those bolt heads at all!

    • @peterbonivart6818
      @peterbonivart6818 Před rokem +1

      @@MonkeyJedi99 Could be that things like caliper brackets are made by VW but the calipers themselves are from a company like Brembo and they may have other ideas about what is good. Automated assembly by robots is also a factor, that's why Torx is so common now, they are well suited to that.

  • @doggone317
    @doggone317 Před rokem +4

    As a shade tree mechanic that does most things several times before I get it fixed it is a joy to watch a professional.

  • @joelnrs
    @joelnrs Před rokem +4

    In this video we learn how to use brake clean.
    Jokes aside. I learn a lot from your videos and also very entertaining. I laugh probably more than I should. Keep up the great work.

  • @petersmart1999
    @petersmart1999 Před rokem +7

    For Whom The Bell Tolls!Glad to hear the guys in the shop appreciate classic metal!

    • @RezaQin
      @RezaQin Před rokem

      Overrated, overplayed Metallica.

    • @petersmart1999
      @petersmart1999 Před rokem +2

      @@RezaQin Most popular,largest selling metal band in history! Yeah they are overrated for sure! You are right and the other 125,000,000 people are wrong over the past 40+ years!

    • @572Btriode
      @572Btriode Před rokem +2

      I didn't know Ernest Hemingway wrote for Metallica.

  • @MrRunner
    @MrRunner Před rokem +3

    I was having tyres fitted once. The goon put the first tyre back on and gunned the lug nuts with an air wrench. I was across the floor at him at sonic speed. Told him to take the tyre off and give me a straight edge. Sure enough, two of the studs were necked.
    They got to replace the studs at their expense and never went back.

  • @TacomaRodeo4
    @TacomaRodeo4 Před rokem +6

    Once again another fine example of a Dorman product. I never had very good luck with Dorman aftermarket parts. I replaced an EVAP canister purge solenoid with a Dorman aftermarket part and it leaked right out of the box. However, they are very good about supplying a replacement part for the failed unit. You're just never sure if it will work or not.

  • @garyhewitt489
    @garyhewitt489 Před rokem +1

    I always get a nice tingley feeling when fitting OE parts.
    It's like getting the right Xmas present from Santa

  • @WickedProxy
    @WickedProxy Před rokem +31

    Would have liked to have gotten a closer look at the plug, crush washer and drain hole to see what actually failed. I'd hate to think all that extra labor was done and more expensive pan was paid for when replacing a faulty crush washer would have fixed it.

    • @Mondos2001
      @Mondos2001 Před rokem +3

      Yes, but add a Taiwanese crush washer and it could have but done. Also permatex isn't as good as it used to be, especially from Walmart..

    • @LoneWolfSparty
      @LoneWolfSparty Před rokem +3

      Ironically enough, if a VW drain plug was used, the crush washer is captured - it comes pre-installed on the drain plug and the washer is NOT removable unless you cut it off. Most VW dealerships replace the drain plugs on the 2.5 at every oil change - cheap insurance. Drain plug is supposed to be torqued to 30 nm if I remember right.

    • @evilgtidriver
      @evilgtidriver Před rokem +6

      A crush washer isn’t gonna keep an impact driver from removing the bolt. Those threads were definitely fucked.

    • @Mondos2001
      @Mondos2001 Před rokem

      @@evilgtidriver on the new pan?

    • @aarong6616
      @aarong6616 Před rokem +1

      If he had to use an impact to remove the drain plug, I imagine whoever installed it last cross threaded it and impacted it in.

  • @cdubbs-small-engines
    @cdubbs-small-engines Před rokem +15

    Seeing an honest mechanic like yourself restores faith in me and proves that everyone is not always trying to rip me off. Thanks for all that you do and share with us.

    • @chrisgollihar8057
      @chrisgollihar8057 Před rokem +3

      Yep. That's why I do most things myself, and what I cant, I have a friend who's a mechanic

  • @ny7294
    @ny7294 Před rokem +2

    The Right Stuff sealant is the best I've found for such applications

  • @bigjbandit
    @bigjbandit Před rokem +1

    Only the best, top -grade Chinesium parts! Well done...both times. 😁

  • @billloomis7611
    @billloomis7611 Před rokem +2

    I'm convinced, don't but Dorman parts.

  • @atikovi1
    @atikovi1 Před rokem +22

    To align the oil pan without smearing the sealant, make some alignment pins by cutting off the head of a matching bolt about 2 inches long. Screw 2 of them in on opposite corners of the engine and then you can slide the oil pan over them in perfect position. Start some of the regular bolts and remove these.

    • @chrism5433
      @chrism5433 Před rokem +1

      I do the same ,works fantastic.cit the head of the bolt ,file a slot .oh yes sir

    • @petero2693
      @petero2693 Před rokem

      Nice trick..I'll steal it

    • @123andme
      @123andme Před rokem

      Dang who has time for that on hourly rate job.

    • @atikovi1
      @atikovi1 Před rokem

      @@123andme Whoever doesn't have the time to do it twice after a comeback for leaks.

  • @toyotatacoma6817
    @toyotatacoma6817 Před rokem +1

    OE parts are not typically made by the vehicle manufacturer, they are outsourced and a lot of aftermarket parts are made by that same manufacturer as the OE parts... So it's possible the oil pan was made by the same manufacturer as the original, the drain plug and crush washer was probably the issue as it reminds me of when someone reuses the crush washer over and over. Could have swapped out the plug and washer to see if that was the issue... But now you have the peace of mind of knowing it's a genuine VW part. AND that sealant? WTF? Permatex is the best! Great job Ray!

    • @mph5896
      @mph5896 Před rokem

      The right stuff, you can put back in service immediately. Permatex calls for 24 hour dry time. I have a large caulk tube of the right stuff, just leave a little out to try up when done, pull out the dried part and good to go for the next job.

  • @AntonioClaudioMichael
    @AntonioClaudioMichael Před rokem +1

    Good old cross thread on the oil drain plug @Rainman Ray's Repairs

  • @thechaun
    @thechaun Před rokem +54

    When you were doing the sealant, I literally thought in my head, "Well, that's not Permatex" right before you said it. As always, love the content. Not a mechanic by trade but I'm a mechanic'
    s son and watching your videos reminds me of the days I spent under cars with him (minus all the cursing and swearing). Those days are long gone but I still apply all the things he taught me to my own vehicles.

    • @imfloridano5448
      @imfloridano5448 Před rokem +2

      Cussin and swearing is what repairs the vehicle😂🤣🤣 oh yeah throwing tools also

    • @willypalooza6519
      @willypalooza6519 Před rokem +3

      Permatex is kinda mid to low tier in my honest opinion. Get some toyota fipg. You'll never go back.

    • @graken22
      @graken22 Před rokem

      @@willypalooza6519 or try the Mopar rtv, It has never failed me in 25 yrs!

    • @thechaun
      @thechaun Před rokem

      @@willypalooza6519 hard to go against something that hasn't failed me in 30+ years and costs half as much as the Toyota stuff.

    • @thechaun
      @thechaun Před rokem

      @@imfloridano5448 As frustrated as he would get, he never threw a tool. Probably the reason I treat every tool I have almost as good as my kids 🤣

  • @amzarnacht6710
    @amzarnacht6710 Před rokem +5

    8:36 - You need **alignment pins** for re-mounting oil pans because trying to hold it in place without fouling your sealant and still lining it up with all of the holes seems like more of a pain that it needs to be.
    If they don't make them, do it yourself with some 2" bolts of the appropriate thread. Snap off the heads, thread three of them into the oil pan upper just as you would with the alignment pins you would use for a wheel. That way you get the oil pan seated squarely, no screwing up the sealant. Once the bolts are set enough to hold the pan in place just take out the improvised alignment pins, replace with the proper bolts, and tighten down.
    Voila - perfectly mounted lower pan.

    • @LilBogota
      @LilBogota Před 4 měsíci

      They sell a gasket for the oil pan

  • @kerman559sanchez4
    @kerman559sanchez4 Před 2 měsíci

    That oil filter housing along with all the other coolant hoses and o rings under the intake manifold are the best

  • @Ironhide236
    @Ironhide236 Před rokem

    Had to pause the video at 19:03 when you pulled out the "vintage" SnapOn torque wrench. I actually have that exact wrench in my toolbox, purchased for me back when I was 16 by my father as a gift for my birthday. I still use it to this day when I work on my car, and it makes me think of him every time I use it.

  • @stevegabbert9626
    @stevegabbert9626 Před rokem +5

    Not requiring a gasket reminded me of my 78' Goldwing. I overhauled the motor, actually I stripped the whole bike apart, and the block separates right down the middle. Both surfaces are milled and only requires their thin yellow sealant, which sets up like rubber. Never leaked a drop of oil.

  • @CargoInk
    @CargoInk Před rokem +10

    Love watching your videos Ray… And I’m an aircraft mechanic (A&P IA).

  • @HUBBABUBBADOOPYDOOP
    @HUBBABUBBADOOPYDOOP Před rokem +1

    *@**15:40*
    To car owner-
    That engine vanity cover will clean up to nearly new condition again,
    by using the original white GUNK waterless hand cleaner.
    Wipe on generously, let sit at least one hour, then wipe off with
    absorbent paper towels only, do not add any water or other cleaners.
    The lanolin residue will help to keep it clean, and moisturize the plastic.
    It's also great for vinyl dashboards, door panels.

  • @jasongrisdale3084
    @jasongrisdale3084 Před rokem

    as soon as i heard the bells i knew metallica's ride the lightning was going to play on the radio and it did...you can barely hear it but it is on the radio...i love working in the shop when hard rock music is on the radio.

  • @1320Jason
    @1320Jason Před rokem +3

    Most shops would’ve put sealer on plug and called it a day. Good for you Ray Ray 👍🏼👍🏼

  • @braddempsey6930
    @braddempsey6930 Před rokem +94

    Draining the fresh engine oil out after the first go around may have seemed to be a waste, but at least the engine got a good flushing out.

    • @Shouk02
      @Shouk02 Před rokem +7

      Lol if you think thats a waste you would hate doing a semi oil pan. My coworker put a new plug in thinking the plug seal was leaking but the thread internet was leaking and i hade to drain 36 qts of brand new oil to replace the pan…

    • @phil6465
      @phil6465 Před rokem +3

      @@Shouk02 But you could have re-used the oil?

  • @frankvitullo3735
    @frankvitullo3735 Před rokem +3

    Good morning Ray. Have a great day! Stay safe

  • @cswango1714
    @cswango1714 Před rokem

    Thats correct!! Actions or material quality speak louder than words!!

  • @kurtelliott1987
    @kurtelliott1987 Před rokem +3

    Two of the things Granpop always said..... "Oil is cheaper than parts" and "It pays to buy the best cause the best is none too good".

  • @neooneZ1
    @neooneZ1 Před rokem +5

    I love the "Brake Clean" pause, it awesome. I also saw the cool tool you used to squish out the sealer. best price ebay, not amazon...love the detail!!!! As always, awesome video 🤙

  • @KECOG
    @KECOG Před rokem

    YAY for the music with the brake cleaner! LIKED for that reason! :D

  • @MikeClowder
    @MikeClowder Před rokem

    The whimsical music when taking the pan off (second time) made me smile for some reason. Great video as always, for some reason at work we've been fighting Dorman QC a bunch, watched this on lunch break. That keeps happening, but like you and our master mechanic have both told me, things come in waves.

  • @jwray9799
    @jwray9799 Před rokem +3

    One word.. PERMATEX second word.. INDIAN HEAD GASKET CEMENT for cork gaskets

  • @Dis-Emboweled
    @Dis-Emboweled Před rokem +8

    Whenever Ray says "Super-high-speef" I turn on X2 speed and let 'er fly!

  • @phr3dmcc0y
    @phr3dmcc0y Před rokem +1

    i love the detail you put into doing your work. man I wish I had your skills.

  • @andrewkiwi1
    @andrewkiwi1 Před rokem

    I used to work in a euro car shop. we had a lot of young guys getting lowered springs put into their Golfs they looked great but you could guarantee that they'd be back within a month or two for a replacement cast aluminium oil pan. Hitting those judder bars in a supermarket car park is enough to split them LOL

  • @ensen89
    @ensen89 Před rokem +5

    I have a 2005 Skoda which is just a cheaper version of a Volkswagen and I head a similar problem. Got a new oil pan installed at a dealership and it leaked from the drain plug.
    At the dealership they told me they made a mistake during install. The oil pans come with a Aluminium washer under the drain plug but that is just some kind of transport protection device. Before filling the engine up with oil that washer needs to be replaced with a copper ring and they forgot to do that. Af the washer / ring was replaced the leak was gone.

    • @ferrumignis
      @ferrumignis Před rokem +4

      I smell a strong flavour of BS from your dealership. Lots of cars use a soft aluminium washer on the drain plug, and why would the drain plug need protection during transport? If it's screwed into the sump then it's not going to get damaged. More likely they forgot to put any washer on.

    • @ensen89
      @ensen89 Před rokem

      @@ferrumignis I stood directly beside the shop manager / master mechanic when he replaced it. So I saw the washer swap with my own eyes. Could still be bs. Maybe they just forgot to give it the right torque and then he made something up.

  • @onryboy2264
    @onryboy2264 Před rokem +3

    I never used black silicone for a oil pan just for that reason.
    It's always been ultra gray sealer for the simple fact that black silicone takes at least 24 hours to fully cure.

  • @andrewpawson6494
    @andrewpawson6494 Před rokem +1

    10:02 When "For whom the bell tolls" starts playing, you know something bad is going to happen!

  • @DconBlueZ
    @DconBlueZ Před rokem

    Thanks for the video, always enjoy watching!

  • @satamanschmidt3428
    @satamanschmidt3428 Před rokem +14

    Ray, you had me up and down on this one. First I was happy seeing that you were using a Valco Cincinnati tube squeezer and then I was down when you didn't use a nozzle on the RTV tube. Then I was shocked when I saw your shop had bought HARBOR FREIGHT RTV. The best RTV is Three Bond out of Japan. This is also available as Hondabond and Yamahabond and a bunch of other Japanese bond relabels as all Japanese cars use Three Bond. Another good one is Victor Reinz. The Permatex is good enough as well and I like the Right Stuff about the best of all the Permatex RTV's followed by the gray Ultra.

    • @craigpounsett7861
      @craigpounsett7861 Před rokem +4

      The genuine sealant he used on the oil pan was actually 3 bond ultra grey most of the vehicles on the road now use 3 bond as a chemical seal

    • @jettamaster3297
      @jettamaster3297 Před rokem

      if you use "The Right stuff" sealer on a pan like this,
      cleaned properly,
      you will hate life if you have to take it off again : )

    • @tsherwoodrzero
      @tsherwoodrzero Před rokem

      Thanks for the tip about rebranded ThreeBond. I was wondering where to get it when I translated the Eunos Cosmo workshop manual as Mazda is quite fond of ThreeBond. Turns out it's made just outside of Cincinnati, Ohio. Also, thanks to M539 Restorations, I've heard nothing but great things about Reinzosil from Victor Reinz. Sreten swears by it and he's a legend in the BMW community.

    • @garyalford9394
      @garyalford9394 Před rokem +1

      The 2 cycle guys use yamahabond to seal their engine crankcases.

  • @lundtland
    @lundtland Před rokem +18

    On a new pan like that I like to scuff up where the sealant is going, sometimes the paint finish does not allow the sealant to adhere well.

  • @Starsnu1
    @Starsnu1 Před rokem +1

    Option B is the true option here. Not all parts are created/manufactured equally. Another reason to almost always use OEM parts. Another great video, Ray. Thanks

  • @tomdixon1213
    @tomdixon1213 Před rokem +1

    Thank you for showing the top of the drain pan. I wondered how you were throwing bolts in there and not losing them.

  • @BorisEkner
    @BorisEkner Před rokem +3

    Watched a few of your videos, I find them educational despite not owning any of the cars maintained. Love it.
    1st question…
    - What’s your opinion on magnetic oil plugs, good or bad?
    2nd question…
    - Why is there never(?) a drain plug on auto transmissions?

  • @BL00193
    @BL00193 Před rokem +4

    as soon as i saw that pan i knew there was going to be an uh oh moment

  • @dosgos
    @dosgos Před rokem +1

    The video special effects are getting great. That second screen inset at speed was epic.

  • @lqueryvg666
    @lqueryvg666 Před rokem +1

    When you said "vintage torque wrench", I chuckled because I have the exact same one in my set.....

  • @mymusicaccount1456
    @mymusicaccount1456 Před rokem +14

    I can guess by the title, they're will be a LOT OF BRAKE CLEAN in this video!
    Can't hardly wait!

  • @ronreneau437
    @ronreneau437 Před rokem +29

    Using a scotch brite pad on the pan sealing surface would help the sealant adhere to the pan.

    • @inoahmann7542
      @inoahmann7542 Před rokem +5

      The Scotch Brite scour pads work great for cleaning up silacone and leaving a good surface for sealant.

  • @neilchilders5442
    @neilchilders5442 Před rokem

    For Whom The Bell Tolls seems to be a fitting song while putting a Dorman oil pan on a Volkswagen.

  • @Torsee
    @Torsee Před rokem

    Very cool Picture in Picture segment.
    Parts collector accumulates fasteners!

  • @strokermk3
    @strokermk3 Před rokem +7

    I agree that aftermarket parts quality really fell of the cliff. I was used to buy aftermarket made in germany parts (I'm from europe) but the brands I used to like and use no longer can because I had so many failures that I lost count. Trying out some made in spain and turkey parts from now on.

    • @ypoora1
      @ypoora1 Před rokem

      A lot of recognized brand names get bought out by Chinese part-poopers sadly.

  • @alannewhall2323
    @alannewhall2323 Před rokem +3

    You did the job and customer right by replacing it but I wonder if some thread tape on the drain plug would of fixed the problem. Regardless it’s done right so the customer doesn’t have to bring it back

  • @pixelmator
    @pixelmator Před rokem +2

    Glad that you are always on top of things Ray, I wish I had you as my mechanic, always do amazing work.

  • @richardsmith2721
    @richardsmith2721 Před rokem

    I liked the repeat because it showed the difference in the part and sealant. I hope this time was successful.

  • @MrMadaket78
    @MrMadaket78 Před rokem +14

    Anybody else notice that there appears to be debris attached to the oil pickup tube screen?

    • @federico494
      @federico494 Před rokem +2

      I was looking for this comment! exactly what I saw

    • @desotosky1372
      @desotosky1372 Před rokem +2

      I was more focused on the debris around the filler cap.

    • @johnscavarda6251
      @johnscavarda6251 Před rokem +1

      Yes! I kept asking "are you gonna clean out the oil pickup screen?"

    • @nainnub1
      @nainnub1 Před rokem

      @@johnscavarda6251 Gee, don't you want to see the "dealers only" repairs make their bogus $ for their bogus services? 🤡

  • @marksaunders2500
    @marksaunders2500 Před rokem +6

    Hi from uk ray👋👍 great job on 2nd run mate not sure what went wrong it had the Chinese stamp of approval onnit🤣 I wish ppl wouldn't put us thru this and just get decent parts to start with it's better in long run 👍 good job tho 👌thanks for your time be safe and see you soon 👍👋

    • @1320Jason
      @1320Jason Před rokem +2

      Chinese stamp of approval
      😂😂😂. Good ole chap!

  • @kafkaian
    @kafkaian Před rokem

    Pure meditation. Thanks bro. Appreciate all you do.
    Ian from 🇬🇧 🏴󠁧󠁢󠁥󠁮󠁧󠁿

  • @EverydayMan83
    @EverydayMan83 Před rokem +1

    Welp, some of us like to not only do a job twice, but now a third time. Yep, after market parts are rough these days. I’ve put 2 wheel bearings on my drivers side and wouldn’t you know it, it’s failed again! This time it gonna be an oem one. Hey at least I’m a pro by now lol, great videos Ray, I love watching them 👍👍

  • @joepanico6480
    @joepanico6480 Před rokem +27

    Another fun source of oil leaks is the vacuum pump at the end of the cylinder head. Costly too!
    PS: The car alarm began sound just as you started the oil pan replacement process, during the sealant application. You didn't heed the warning.

    • @BFMV409
      @BFMV409 Před rokem +1

      Yeah, ended up deleting my vacuum pump.

    • @Gromitdog1
      @Gromitdog1 Před rokem

      Why would the naturally aspirated 2.5 gas have a vacuum pump in the 1st place?

    • @losi8ightyew
      @losi8ightyew Před rokem +1

      @@Gromitdog1 You'd be surprised man. Volkswagen is known for cramming those things on every engine they can. My Mk4 1.8T has gone through 4 of em.

    • @BFMV409
      @BFMV409 Před rokem +2

      @@Gromitdog1 I think it's supposed to give more assistance and consistent feel to the brakes.

    • @joepanico6480
      @joepanico6480 Před rokem

      @@losi8ightyew Just thought to ask ... how many steering column locks have you changed? I fixed mine and one of my employees (not part of his pay scale; just 'cause I could.)
      Trick: don't drill-out the security, break-away bolts. Use a punch and hammer to work loose.

  • @alanglover1605
    @alanglover1605 Před rokem +9

    After 15 years in the vw audi trade , selling both oe and aftermarket parts , on parts designed to keep oil in place , ie oil pans and rocker covers, oe was the only way to go.

  • @dannyshoop1677
    @dannyshoop1677 Před rokem

    Something bout spreading sealant that just relaxes me !!

  • @orwellboy1958
    @orwellboy1958 Před rokem +2

    My favourite saying "buy cheep, buy twice"

  • @gregbutler9873
    @gregbutler9873 Před rokem +6

    Chinese replacement parts … my wrench slinging hero . Always mate up to the previous part and check for correct tolerance according to OEM print if possible. Part stores and OEM knockoffs should be checked for overall quality .✌🏼🍻

    • @nickmalone3143
      @nickmalone3143 Před rokem

      China is your master now ....thanks to corrupt congress usa manuafacturing has been sold out like Judas

  • @PurityVendetta
    @PurityVendetta Před rokem +11

    I'm from the UK and I know as soon as you said Dorman trouble was in the offing. I've watched enough of your videos and read the comments and Dorman seem to be the equivalent of Bearmach parts for Land Rover here in the UK.
    I work mainly on vintage British motorcycles an unfortunately due to prehistoric manufacturing processes I have to be an engineer, a fitter and a mechanic all at the same time. I think we can all feel the good vibe when you used the VW OEM sealant 😊

    • @therandomchannel2022
      @therandomchannel2022 Před rokem +3

      Oh man Dorman is so crappy, they really should be banned. I've never seen a good quality Dorman product ever.

    • @PurityVendetta
      @PurityVendetta Před rokem +2

      @@therandomchannel2022 We have plenty of crappy parts here in the UK too. The trouble is the customers always want cheap. I can't say I blame them with the way things are but I refuse flatly to use anything other than known make parts or OEM for brakes, knuckle joints etc and clutches. The amount of stress with el cheap crap isn't worth the effort.

    • @barney2633
      @barney2633 Před rokem

      You mean Britpart.. Bearmach are good. I have worked on landrovers for years.

    • @PurityVendetta
      @PurityVendetta Před rokem

      @@barney2633 Don't use either if it's a mechanical part. Bearmach hubs are rubbish. Had two fail within 6 months. I have worked on Land Rovers longer than I can remember.

    • @xalty1200
      @xalty1200 Před rokem +2

      URO, Shitpart, Eurospare are all on Dorman's level.
      Febi, Meyle, etc are usually a step up but not always

  • @neillleblanc4039
    @neillleblanc4039 Před rokem

    Lol the minute I herd Dorman Eric O popped up in my mind calling it garbage and he wasn't lying!!

  • @badassbiker1974
    @badassbiker1974 Před rokem

    Thanks Ray. 😊

  • @dhandler1
    @dhandler1 Před rokem +2

    Ray, you are an excellent and caring mechanic who takes pride in his work. I wish there were more like you. BTW, in German, they pronounce Volkswagen "FolksVagen". "v" is pronounced like we pronounce "f" and "w" is pronounced like we pronounce "v".

  • @dspautocrosser
    @dspautocrosser Před rokem +8

    This will continue to be a problem for those of us with older cars we want to keep running that don't have a huge aftermarket following. Decent cars in junk yards are drying up and many, many parts are NLA from the dealer. A lot of times you don't have much of an option but to roll the dice on an aftermarket part.

    • @theundergroundlairofthesqu9261
      @theundergroundlairofthesqu9261 Před rokem +2

      With German cars, aftermarket parts are generally fine -- you can buy most things from the very same company that made them for the German automaker. Usually going Dorman or URO is a choice, not a necessity. Almost always, really.

    • @BFMV409
      @BFMV409 Před rokem +3

      Surprisingly good resources for German cars. Especially for VW/Audi cars. FCP Euro and ECS Tuning are fantastic.

    • @brisiobrien1
      @brisiobrien1 Před rokem +1

      Surprisingly, OEM genuine VW from Jim Ellis in Atlanta is the way to go and cheaper than most other places.

    • @theundergroundlairofthesqu9261
      @theundergroundlairofthesqu9261 Před rokem

      @@brisiobrien1 Yeah, you never know. I never got any deals from my local VW dealer back in the day, but am now getting the "cool guy price" at a different dealer and its so close to aftermarket that it's hard to resist sometimes.

  • @JBreeze4598
    @JBreeze4598 Před rokem

    At 10:03 queue the music, "F0r Whom The B3ll Toll$" Priceless!! Thanks for sharing Ray.

  • @alternative2104
    @alternative2104 Před rokem

    Reminds me too much of an A4 I worked on I've got deja Vu. You've got much more patience than me for sure. Good job

  • @williamgilroy5217
    @williamgilroy5217 Před rokem +20

    I don't understand the benefit of sealants over gaskets. It seems to me a well crafted gasket solves everyone's problems and establishes quality seal everytime.

    • @KeithHeinrich
      @KeithHeinrich Před rokem +2

      CZcams AMG engine assembly. Those engines are precisely sealed with sealant applied by robots. If its good enough for AMG, then its good enough for Volkswagon I guess.

    • @jameslastname9171
      @jameslastname9171 Před rokem +5

      Cost savings by manufacturer

    • @watershed44
      @watershed44 Před rokem +2

      @William Gilroy
      Bean counters ruin everything. It's a cost saving measure for the mfrs.

    • @AnhYeuEmMaiMai69
      @AnhYeuEmMaiMai69 Před rokem +1

      they last a lot longer. When I did my oil pan at 155K due to excessive rust, it still was not leaking

    • @hdfxrs9121
      @hdfxrs9121 Před rokem +2

      My older Civic EX has an aluminum pan which requires RTV only, while the other model Civics had steel pans that used a gasket. I would have preferred the gasket, even an MLS.

  • @handymandev03
    @handymandev03 Před rokem +3

    Just ask Eric o about dorman parts lol

  • @oldk4tz
    @oldk4tz Před rokem +1

    i know you hate doing your job twice because of inferior parts we all do. but i like watching it.

  • @bad05ford
    @bad05ford Před rokem

    Local shop has used numerous Dorman pans and no issues. I have the rear diff cover for the 08 up super duty and it fits perfectly and seals.

  • @Herbertti3
    @Herbertti3 Před rokem +3

    At least engine is properly flushed now.

  • @davidturner4639
    @davidturner4639 Před rokem +3

    Curious about the Dormant oil pan leak, was it poorly cut threads, porous welds, or?

  • @stevo4649
    @stevo4649 Před rokem

    thankyou Ray,,and a good day to you..👍👍

  • @1DarkStorm
    @1DarkStorm Před rokem +1

    Welcoming back!

  • @johnt.848
    @johnt.848 Před rokem +8

    If the first replacement sump worked why increase costs and replace it again? The only issue I saw was the wrong crush washer used on the drain plug, use a thicker copper washer, not alloy, it would have saved a lot of time and work.

    • @brucepickess8097
      @brucepickess8097 Před rokem +2

      Yes that was my thought as well, strange decision.🤔🤔

    • @mrfrenzy.
      @mrfrenzy. Před rokem +1

      What if it was the sealing surface on the pan that was bad? Then he would have wasted another batch of oil and another day the customer was without his car. Not worth it to take the risk again.

    • @hardluckvintagegarage6968
      @hardluckvintagegarage6968 Před rokem +2

      The original pan had the drain bolt cross threaded and the threads were all galled up. It was going to leak if Ray tried putting the drain bolt back into it. That being said, I would have tapped the drain plug out to the next highest size and put in a new drain plug.

    • @johnt.848
      @johnt.848 Před rokem +1

      @@hardluckvintagegarage6968 my question wasn't about the original sump pan.

    • @johnt.848
      @johnt.848 Před rokem +2

      @@mrfrenzy. it was leaking from the sump plug, a copper washer would have fixed that.

  • @PMD_Bill
    @PMD_Bill Před rokem +13

    So did you do a post-mortem to find out what actually failed? Was it a bad pan surface, a bad drain plug gasket, or was the drain plug itself bad?

    • @MrPropanePete
      @MrPropanePete Před rokem +2

      I was waiting for the autopsy too but as a former mechanic I would say the sump plug was cross threaded. On VW's (and most cars these days) you always fit a new sump plug and crush washer each time you change the oil.

    • @frankhage1734
      @frankhage1734 Před rokem

      Ray didn't check the brand new crush washer and pan for debris on the sealing surfaces.

    • @BlamBlam80
      @BlamBlam80 Před rokem

      @@MrPropanePete it seemed he had a problem removing the drain plug the 1st time so if he used the same one again then I would assume that is the culprit. Therefore, this issue could be operator error, sorry Ray.

  • @stanSnider
    @stanSnider Před rokem

    Good morning Ray

  • @AntonioClaudioMichael
    @AntonioClaudioMichael Před rokem +1

    That bead the vw sealant is doing is super niceni bet it will seal this time oh yeah 😎 @Rainman Ray's Repairs

  • @auxmike718
    @auxmike718 Před rokem +2

    A factory plug and gasket would have fixed this in a jiffy!

  • @hiscifi2986
    @hiscifi2986 Před rokem +4

    I would have tried to find the fault of that drainplug seal, maybe there was just a metal shard from the machining process.. If all else fails, use a fibre washer.

    • @h2o100c
      @h2o100c Před rokem +3

      Agree. The problem was ONLY the washer on the new pan! Ray ripped off the customer this time.

    • @marioreali5925
      @marioreali5925 Před rokem

      @@h2o100c You really think they charged customer twice? No way.

    • @h2o100c
      @h2o100c Před rokem

      @@marioreali5925 I never said twice but it could have been double the cost for the OEM pan

    • @marioreali5925
      @marioreali5925 Před rokem

      @@h2o100c Could very well be much higher price but worth it I think.

  • @vincemota4357
    @vincemota4357 Před rokem

    I am nowhere near an experienced step mechanic . I usually send out my car to get fixed. I'm only as mechanical as a printer allows me to be. Even though it was a pain in the butt to do it a second time, I really appreciated the lesson Learned using the preferred sealant.

  • @rafaelbetancourt3551
    @rafaelbetancourt3551 Před rokem

    love the shiny new german oil pan

  • @JRattheranch
    @JRattheranch Před rokem +4

    The lesson learned, Ray, is buy cheap, buy twice... Well known by you and I but obviously not to the parts supply department.

  • @stevealan2289
    @stevealan2289 Před rokem +10

    You got a Dorman pan with a bad sealing washer, I've had it happen with parts directly from the dealership. Nice to see you tried a new .50 cent sealing washer instead of upselling a customer an overpriced dealer part that's the exact same quality. Secondly, that gasket your parts guy got you was for the lower pan after a quick search of the P/N and gaskets should always be used when available as opposed to RTV. I don't know what it is but I love some of your videos and other ones have me boggled, I bet your bosses love the revenue though!

  • @jontibbetts9724
    @jontibbetts9724 Před rokem

    @ 6:19.... not even a flinch this man is steady 🤘

  • @clay282
    @clay282 Před rokem

    Am I the only one, that all but squeals with happiness, when he pops out the brake cleaner and the dramatic music hits? No...? Me neither. I was actually asking for a friend LOL

  • @joen2418
    @joen2418 Před rokem +5

    I was never a fan of "gasket in a tube," I would rather use a true gasket with a little "hi tack" and a dab of blue loctite on a couple of bolts to ensure it stays put.
    Never had a job returned during my time working at the VW dealear, or anytime in my automotive career.

    • @NoWr2Run
      @NoWr2Run Před rokem

      I use " INDIAN HEAD SHELLAC " NOTHING LEAKS WITH THAT STUFF.

    • @losi8ightyew
      @losi8ightyew Před rokem +1

      @@NoWr2Run That's some old school stuff. When I was a kid just getting started with engines, I worked on 2 cycle Maytags and that stuff was all we used!!

    • @NoWr2Run
      @NoWr2Run Před rokem

      @@losi8ightyew Yes Sir, That is " OLD SCHOOL ", My Dad used it & so I followed suit, LOL. It's a bugger too get off but IT DOES NOT LEAK.
      I also us MOPAR BLACK SILICONE on some stuff, Neighbors a MOPAR Mechanic & gives it too me for free. That stuff never let me down either. The key is " THE SURFACE HAS TOO BE VERY CLEAN & FLAT ". Like when you're painting something, it has too be very clean.

    • @johncooper4637
      @johncooper4637 Před rokem +1

      Toyota sells one for sealing their oil pans that is better than Ultra Black. You have to drive a razor blade in around the edge to get that stuff loose.

  • @mike_dodane
    @mike_dodane Před rokem +6

    The engineer that designed that oil pan must have thought they were saying “more torx bolts” instead of “more cow bell”

  • @HouseCallAutoRepair
    @HouseCallAutoRepair Před rokem

    I ran into this once, with a Subaru. All went wel. No leaks....
    Next day, down a quart and when running, there was a steady stream. Right through the upper oil tube welds....

  • @billziegmond4943
    @billziegmond4943 Před rokem

    Got to love the flying wallet.