I did the same thing because I had two M365s, but I put the second controller where the battery is normally installed and stuffed the two batteries in a bag attached to the seat actually really unnecessary because I use both at once anyway that I can get much faster but not really further despite the second battery also my scooter is now a free ticket for a court hearing as soon as I'm stopped. You can do it if you're bored and want to prove it that works 🤣
Can i ask you where did you find the peace that you put to the weel for the front disc brake ?? and if i can to extend the power of controller to give more power in the motor
The reason is that he used one controller which is supposed to be two to power both hub motors and not only did he use a single controller, he used a very weak controller. If I'm not mistaken on my estimate that controller should be in the range of 10 amps to 14 amps of power out, even worse that it is at 36volts A modification like in this video with proper/adequate components can hit easily above 50km/h
You made a new bracket? Why not use the original bracket + brake calipers on the rear wheel? Ah never mind, I figured it out: 6 hole adapter plus larger discs, original 5 hole disc is only 110mm
bro! dont need to used to panel board .. there are some tricks in wirings just watch my video for you to show the single finger throttle with dual controllers and dual hub motor
Brilliant! You are very skilled.
wow this looks amazing
just what i used to think about weeks ago
Pero si se parece un G30 .... D: hubiera agarrado esa plataforma y la hubiera hecho DHM y DDB
I did the same thing because I had two M365s, but I put the second controller where the battery is normally installed and stuffed the two batteries in a bag attached to the seat actually really unnecessary because I use both at once anyway that I can get much faster but not really further despite the second battery also my scooter is now a free ticket for a court hearing as soon as I'm stopped. You can do it if you're bored and want to prove it that works 🤣
Put some 10 inch tyres on the wheels to make it higher...
Very creative man!
You need 10 “ wheels yes or yes
Also you need from suspension and the best is rear suspension tooo
El tornillo de soporte freno se coloca desde el interior y se sujeta con tuercas no con mierda de silicona
use dual fsesc instead of common speed controllers
Wow thanks for the info. Just searched for it and it looks interesting
Good one with the threaded bolt end in the motor, much better than bending in the forks or buying fancy adapters.
😂 no that's stupid as fuck the bolt won't stop the axle from turning instead of the wheel #ignorance
Do you upgrade the controler? Or using the current one?
Think it’s just one controller that’s y it’s slow lol
he upgraded to a 48 volt
@@sad_clappzy9776 he did not in this video.
It needs 10" Tires
Can i ask you where did you find the peace that you put to the weel for the front disc brake ?? and if i can to extend the power of controller to give more power in the motor
Sir how did you connect the LCD display without error 10 i was use that in other scooter but the LCD display is error 10
why you have double display lcd why not one ?
Hmmm it’s not adding up. My XIAOMI hits 33kpm with firmware
The reason is that he used one controller which is supposed to be two to power both hub motors and not only did he use a single controller, he used a very weak controller. If I'm not mistaken on my estimate that controller should be in the range of 10 amps to 14 amps of power out, even worse that it is at 36volts
A modification like in this video with proper/adequate components can hit easily above 50km/h
What the size of brake disc adapter?
6 holes and 44mm or 48mm?
Do you have a page I can reach. I'd like to dual hub my scooter.
super
Hi! Great job with the front brake disc!👍 Question: which glue did you use to glue the 6-hole adapter? Kind regards.
Hola qué tal?
Saan po kayo sa pilipinas?
can you use ONE motor som Generator to load and the other for drive? so have you more options.Speed if you need and load for higher Range..
Boss ano ginamit mo na spacer dyan sa rear motor mo at ano din ginamit mo para makapagkabit nang disk brake sa motor salamat sana mapansin boss
Double voltage and battery
Like 65 hi friend ☺
You made a new bracket? Why not use the original bracket + brake calipers on the rear wheel?
Ah never mind, I figured it out: 6 hole adapter plus larger discs, original 5 hole disc is only 110mm
To je prasárna 😂
bro! dont need to used to panel board .. there are some tricks in wirings just watch my video for you to show the single finger throttle with dual controllers and dual hub motor
Can you send me a link?
Won't using 1 controller limit the power of both hub?
Bossing dba delikado yan? 3 lng na bolts kumakapit?
kamusta naman sir? bumilisba or feels like the same?
Pre may shop ka dto sa pinas?
idol pede e dual motor pero isang motor eh pang pro
Pano m onapagkasya sa likod yung motor at hub paps? Diba non pro yan?
san mo manili yung diskbreak mo
Looks slow
It don’t look that fast bro
Pwede ba isang throttle connection sa dalawang controller?
hina ng boses mo idol
pa fan sign po
After going to all that work you should have upgrade and buy a new scooter🍼 🤣😅😂