IPMS Cyprus 14th Exhibition/Contest 2019: Commendation in Standard Category Revell Pirate Ship 05605 Scale: 1/72 Length 55cm and Height 47cm Number of Pieces: 896 Read comments for a full review and tips.
Revell Pirate Ship 80-5605 or 05605 Scale: 1/72 Length 550mm and Height 470mm Number of Pieces: 896 Level of Difficulty: 5 All I can say about this particular box is that everything fits perfectly. No flash, not even a trace, no need to drill anything, all detail is there, everything about this box was just perfect. This is the pirate ship which I painted black and followed the instructions of the black pearl version. Everything is the same except the figure under the bowsprit. Reason behind this simply to save money since the black pearl sells for over 100 euro while the pirate ship I purchased for 55. All other details are the same. Flags are of the paper kind in both cases. Instructions are very clear and for the rigging I followed the instructions of Revell. Some items to watch out: Steps 10-11: Make sure you glued the cannons well so you will not lose any after you have put the ship together. One of mine unglued but I managed to get it back. Steps 20-21. Gluing them together and then trying to attach them on the ship might cause you a problem. Mine unglued so I had to glued the two halves again while they were set on the ship. Step 34: Do not attach the two parts on the ship now. Leave them at the end. 99% at some point you will hit them with your hands or a tool. Step 40: BE CAREFUL! Not all the cannons will be inside or outside at the top deck. Four will have to be the opposite of what you choose to have enough of the parts (I4, I5, I6, I11, I12, I13) Step 51: Added the string on the cannon hole covers before gluing them on so I only had to tie them to the top part. Step 55-60: A bit use of force for the parts to get into place but they did. Maybe a bit of sanding needed. Step 74: Make sure you follow the instructions. Do not glue the top part. Step 75-79: I did not glue the D parts, as it would have made it difficult to do the rigging on the masts. (D1, D2, D3, D4, D5, D6, D7, D8, D9, D10, D11, D12) I added them when I worked on the specific masts and doing the rigging from the sails down. Add all strings to sails before you glue them on. Step 88: This is a sail I left behind and added it a bit later. It is up to you. It was easier for me to work the rigging without the particular sail in place. It will cause a bit of a problem setting it up since it hangs and it is not glued to anything. In general, I really enjoyed this ship. No problems. I placed some strings differently than suggested simply because I could not either reach, or it was too difficult to tie them where suggested but this was my choice.
Goodmorning. The reason it says revell pirste ship is because that is the box I used. This is not the black pearl box. (Different figurehead). It is essentially the same kit. Purchased the pirate at a much cheaper price and downloaded the black pearl instructions. So wanted to be accurate. 😉
Super awesome! I just bought this kit 2 weeks ago and started painting it immediately. I've literally gone through 4 things of Testors flat black and 2 things of testors gold. Im almost done painting all the parts. I really just cannot wait to start putting her together! I feel like painting is never ending!
Thank you so much for your lovely comments. Nice to wake up with some positive comments than all the hate and negative attitude that is around us and on the internet. Good morning, thank you
If you're thinking of building the model then be aware putting the guns together is a nightmare and regardless of the instructions fit them to the decks before assembling the ship!! My model is coming along but the instructions are to paint the hull after assembly, l think this is wrong!! Unfortunately my looks as if the guns won't be displayed at all. But Theodoros example is exceptional, fabulous, well done. :)
thank you for your kind comments. The only reason I mentioned "pirate ship" is because the actual box I used was that of the pirate ship. I will add it to the tags though. Thank you. Hope some of my advice helped
How long did that take. Blooming impressive. I have got one for Christmas so once I get the glue I will start it. Its gonna be the biggest model I've ever done.
@@theodorostzitzimbourounis thank you very much. I never thought I could do it but little and often. But well impressed I think the hardest part for me was the rigging and twine. Yours looks so smooth I love it. I huge well done and I can honestly say I know how you felt duing the build lol ⚓⛵👍🤗
Good morning, thank you for the kind words. Basically the main paint is revell anthracite grey 9. Did not mix it with anything. I paint it a couple of hands. Now in my limited experience when painting large pieces that ara not just flat like the sails but have grooves and so on the paint sticks well. In the case of the sails though I knew I will be in trouble if i did that so I applied first Vallejo black primer. After 24 hours I applied the paint one hand and it came out pretty smooth I think. So everything was hand painted no spray guns.
thank you so much. Coming from you means a lot cause I have looked at your work. I do this as I say in my comments over weekends and nights so even the smallest plane takes me some time. This ship took me almost 8 months. I know its not perfect but people should not be afraid to try out. That is why I put these videos up. :) Thank you
No i did not use beeswax. Used on previous ship. You use it so the thread does not get that furry look. What i do is that i do not tie a final knot or use glue until the end or until the point i realize i will not be able to reach it. The reason is that you work on a mast at a time and by adding sail after sail the mast might move even the slightest from the weight. Especially on this ship the sails are heavy. In addition you have horizontal lines going from mast to mast so again you might pull to tight. Finally the weight of the hanging sails. It is better then to tie the knot but leave extra line so when almost everything is in place you can finalize then the knot and use glue.
Hi. I translated your question so hopefully i understood correctly your question . There is a goose because as i stated in my comments, this is the pirate ship box. I simply painted it black. There is no difference between this and the black pearl box except price and the ornament at the front
Revell Pirate Ship 80-5605 or 05605
Scale: 1/72
Length 550mm and Height 470mm
Number of Pieces: 896
Level of Difficulty: 5
All I can say about this particular box is that everything fits perfectly. No flash, not even a trace, no need to drill anything, all detail is there, everything about this box was just perfect. This is the pirate ship which I painted black and followed the instructions of the black pearl version. Everything is the same except the figure under the bowsprit. Reason behind this simply to save money since the black pearl sells for over 100 euro while the pirate ship I purchased for 55. All other details are the same. Flags are of the paper kind in both cases. Instructions are very clear and for the rigging I followed the instructions of Revell.
Some items to watch out:
Steps 10-11: Make sure you glued the cannons well so you will not lose any after you have put the ship together. One of mine unglued but I managed to get it back.
Steps 20-21. Gluing them together and then trying to attach them on the ship might cause you a problem. Mine unglued so I had to glued the two halves again while they were set on the ship.
Step 34: Do not attach the two parts on the ship now. Leave them at the end. 99% at some point you will hit them with your hands or a tool.
Step 40: BE CAREFUL! Not all the cannons will be inside or outside at the top deck. Four will have to be the opposite of what you choose to have enough of the parts (I4, I5, I6, I11, I12, I13)
Step 51: Added the string on the cannon hole covers before gluing them on so I only had to tie them to the top part.
Step 55-60: A bit use of force for the parts to get into place but they did. Maybe a bit of sanding needed.
Step 74: Make sure you follow the instructions. Do not glue the top part.
Step 75-79: I did not glue the D parts, as it would have made it difficult to do the rigging on the masts.
(D1, D2, D3, D4, D5, D6, D7, D8, D9, D10, D11, D12) I added them when I worked on the specific masts and doing the rigging from the sails down. Add all strings to sails before you glue them on.
Step 88: This is a sail I left behind and added it a bit later. It is up to you. It was easier for me to work the rigging without the particular sail in place. It will cause a bit of a problem setting it up since it hangs and it is not glued to anything.
In general, I really enjoyed this ship. No problems. I placed some strings differently than suggested simply because I could not either reach, or it was too difficult to tie them where suggested but this was my choice.
It's not just any pirate ship, mate. It's the Black Pearl.
Goodmorning. The reason it says revell pirste ship is because that is the box I used. This is not the black pearl box. (Different figurehead). It is essentially the same kit. Purchased the pirate at a much cheaper price and downloaded the black pearl instructions. So wanted to be accurate. 😉
@@theodorostzitzimbourounis It still looks cool, doesn't matter what kit it is.
@@chrisduitsman2918 thank you so much....
STOP BLOWING HOLES IN MY SHIP!!!! 🤣 Outstanding detailing sir congrats.
thank you kindly.
I believe this Revell kit is a reboxed Zvezda kit, just an fyi to potential buyers.
Super awesome! I just bought this kit 2 weeks ago and started painting it immediately. I've literally gone through 4 things of Testors flat black and 2 things of testors gold. Im almost done painting all the parts. I really just cannot wait to start putting her together! I feel like painting is never ending!
Thank you for the comment. Good luck with the ship. Send a link when finished.
@@theodorostzitzimbourounis thank you so much! I promise I will send you a videos of her when she's finished! Cheers!
@@dkstryker Did you ever finish it?
Great job.....very inspirational! That’s a lot of detailed work! Congrats!
Good morning and thank you for the beautiful comment. Now thta we need to stay in our homes it is time to start another project. :)
Nice job .. The dark gray look neat and the gold really stands out .. Well done
Thank you for your comments. I wish you and your family Merry Christmas and always in good health.
Excellent work, your skills are admirable.
Thank you so much for your lovely comments. Nice to wake up with some positive comments than all the hate and negative attitude that is around us and on the internet. Good morning, thank you
I love this Pirate Ship!
Good morning. I will let you have it if you agree to share the loot from your sails Erik the Pirate :)
Great Job !!
If you're thinking of building the model then be aware putting the guns together is a nightmare and regardless of the instructions fit them to the decks before assembling the ship!! My model is coming along but the instructions are to paint the hull after assembly, l think this is wrong!! Unfortunately my looks as if the guns won't be displayed at all. But Theodoros example is exceptional, fabulous, well done. :)
Thank you for the comments. Anything i can help with drop a line.
Great job ! :o)
Thank you Daniel.Merry Christmas and a Happy New Year full of laughter and in good health.
@@theodorostzitzimbourounis Same wishes for you ! :o)
Espetacular!
thank you
i want it
Great video my man but you should definitely change the title from pirate ship to Black Pearl.
That's the name of the ship after all
thank you for your kind comments. The only reason I mentioned "pirate ship" is because the actual box I used was that of the pirate ship. I will add it to the tags though. Thank you. Hope some of my advice helped
It s not the black Pearl because of the animal on the front of the boot
For thé black Pearl it’s an angel, or a lady
@@killianbernard2513 a lady with a bird on her hand i think, also the model would need more triangular sails
How long did that take.
Blooming impressive.
I have got one for Christmas so once I get the glue I will start it.
Its gonna be the biggest model I've ever done.
Thank you. Good luck and when finished send me the link. Happy new year wishing you and your family good health and smiles
Just saw your video. Nice job man. The satisfaction when you complete a project surpasses all the cursing. :) beautiful
@@theodorostzitzimbourounis thank you very much.
I never thought I could do it but little and often.
But well impressed I think the hardest part for me was the rigging and twine.
Yours looks so smooth I love it.
I huge well done and I can honestly say I know how you felt duing the build lol ⚓⛵👍🤗
How did you paint the hull? What paints did you use/mix? Great job!
Good morning, thank you for the kind words. Basically the main paint is revell anthracite grey 9. Did not mix it with anything. I paint it a couple of hands. Now in my limited experience when painting large pieces that ara not just flat like the sails but have grooves and so on the paint sticks well. In the case of the sails though I knew I will be in trouble if i did that so I applied first Vallejo black primer. After 24 hours I applied the paint one hand and it came out pretty smooth I think. So everything was hand painted no spray guns.
Great job
thank you so much. Coming from you means a lot cause I have looked at your work. I do this as I say in my comments over weekends and nights so even the smallest plane takes me some time. This ship took me almost 8 months. I know its not perfect but people should not be afraid to try out. That is why I put these videos up. :) Thank you
Toop Toop
How did you get the rigging to stay so straight? Did you use beeswax or anything? It looks great!
No i did not use beeswax. Used on previous ship. You use it so the thread does not get that furry look. What i do is that i do not tie a final knot or use glue until the end or until the point i realize i will not be able to reach it. The reason is that you work on a mast at a time and by adding sail after sail the mast might move even the slightest from the weight. Especially on this ship the sails are heavy. In addition you have horizontal lines going from mast to mast so again you might pull to tight. Finally the weight of the hanging sails. It is better then to tie the knot but leave extra line so when almost everything is in place you can finalize then the knot and use glue.
@@theodorostzitzimbourounis good stuff! Thank you so much for your reply and good advice!
Ωραίο μοντέλο φίλε
Σε ευχαριστω. Metallica, saxon, iron maiden, motorhead, και η λιστα συνεχιζετε ολα σε βινυλιο. Χρονια στην πλατη μου οπως το πλοιο. 😁
@@theodorostzitzimbourounis φιλε εισαι δύναμη 🤘👊
Hello men, could you help me?? Because normally the color of the sail are white, but yours are black
Did you peint them?? Thanks!
Hello. I painted them first with vallejo black surface primer and then the revell black. What you see is handpainted. No airspray. The primer helped
Theodoros Tzitzimbourounis tank you verry much!!
Почему там гусь на носу?
Hi. I translated your question so hopefully i understood correctly your question . There is a goose because as i stated in my comments, this is the pirate ship box. I simply painted it black. There is no difference between this and the black pearl box except price and the ornament at the front
Halo
Hello, thanks for visiting hope it helped.
link pembeliannya om.
amazon.de