Sitting 20+ years will this $500 Truck Run & Drive again? (International Loadstar Revival)
Vložit
- čas přidán 6. 04. 2022
- See the first video on this truck here: • $500 Dump Truck sittin...
Grab a Shirt and hat at the Merch Store! dieselcreek.com/
Like something you see in a video? good chance its linked in my Amazon Store: www.amazon.com/shop/dieselcreek
Save yourself 5% and help support the channel by Getting some sweet gear from Yankum Ropes here!
yankum.com/?afmc=dieselcreek
Use the code dieselcreek at checkout for 5% off your purchase!
-If you’d like to help get the Autocar back on the road you can help out here: / dieselcreek
OR send a One Time Contribution Via PayPal to DieselCreek@gmail.com
-Custom Music made for me by Vinnie Longhi of the Semi-Supervillains
Check them out here: / tssvillains
-Wanna send me something? Sent it to:
Diesel Creek
P.O. Box 109
Burgettstown PA 15021-0109 - Auta a dopravní prostředky
I think you’re wonderful! I’m a 71 year old lady whose only mechanical claim to fame was dropping the engine on an old VW bug when I was 18, and rebuilding it with the help of a hippie handbook called “Volkswagon Repair for the Complete Idiot.” I knew nothing going in, but the darn thing ran for years after I got the engine back in it!
That book was da bomb! It even told you when it was time to take a smoking break, which I didn’t need, but years later I finally wondered what it was he was lighting up!
I remember pulling over and adjusting the idle with a bobby pin when it ran rough, as I didn’t carry any tools!
Wow, what a wonderful read.... Much love from 🇬🇧.
Good on you for dropping that engine blind! I guess it’s debatable what “smoke “ they were suggesting!
Reverse gears are straight cut gears on a bunch of gearboxes,even today.
Straight cut gears are noisy.
Yeah kinda hard to tell over a video and not in person but straight cut gears were my though aswell.
That is what I was thinking also. Looks like a really good dump truck to me
I’ll add my 32 years as a mechanic on this. I’ve never heard a manual transmission with a quiet reverse gear, regardless of scale.
That's right, All the old Internationals are like that... as I remember :) Reverse gears whine. That's what makes it a "Binder"
Was just going to say reverse gear is a straight cut gear so its extremely loud. You all beat me to it. The old Chevy 366 5 speed I drove was the same in reverse and first gear.
I can't believe CZcams hid your channel from me for so long. I absolutely love it!
This truck turned out to be one of those edge cases, where the repairs needed are moderate, but doable. And a lot of stuff that would typically be stuck, broken, impossible to repair and/or get parts for, were all in workable order... What a sweet old truck! They sure as hell don't build them like that anymore! I can see why you would want a 4-door, 4-wheel-drive version of it. One of those, done up nice, with some updates, would be damn cool.
When you mentioned how rebuilding a carb can seem daunting, it reminded me of my first time; I remember the Chilton's manual saying "Don't let it intimidate you; remember, it's only a carburetor."
Gr8fulFox , Yeah... ONLY a carburetor!
Working on a F-100 truck I gave up on Chiltons. Under air-conditioned fan replacement it said. REMOVE DASH of installation is reverse on in stall.
First time i ever dealt with a carb at work i was so worked up about it. Now its "just a carb" not like most all cant go back together anyway but the right way 🤷♂️ always learn somwthing new but not nearly as daunting as it used to be.
@williamkowalchik572 yeah i get that alot at work to "install is reverse of removal" and its really annoying like obviously its reverse of removal, but the tools and methods you used to remove dont necessarily install it again....
@@braap802 I keep my vehicles till the cost out weight the vehicle. So I buy uses and get the factory service manual to go with it.
Hey Matt, I used to haul gravel back in the early 70's with a 1960 International dumptruck . One of the most reliable, good running trucks ever. Wish you good luck with yours. Name, maybe, Big Red. It's what I named mine. Take care and best wishes. 👍
Nice! Gravel is a fun side gig nowadays, about 5 years ago I started my gravel hauling gig with a 1988 F350 7.3 IDI DRW with the ZF5. Still have it, and I'm considering putting a dump bed on it but I see videos like this and I think my money would be better spent on reviving an antique medium duty like THIS one 🚛
@@FarmerDrew might be! But it is a gamble - you might spend a lot more than the cost of your upgrade if many systems are shot, just keep that in mind before you decide. Whatever you decide: Good luck and Godspeed.
cutie vv
the truck ^ ^
i also suggest Bir Red for the name.
Typo - Big Red.
I love the old international loadstar such a beautiful body lines seeing that it’s red I would call it Clifford. Since it’s going to be a yard dog of a truck. Keep up the good work and stay safe out there.
Yes, it looks like a Clifford!
Clifford🤙🤙🤙
Just call it mine if I was you. It's yours an let the haters hate.
she looks SO HAPPY racing down the road again! Like she's all young again!
Still hoping to see this classic International restored and put back to work. It hurts to see it just sitting in the woods rotting away.
As far as a name I think Clifford fits. Ya know the big red dog. Friendly and always willing to help out.
I'll second Clifford. I was coming to write my own recommendation, but I like yours better.
Third!
I was gonna suggest "Ethyl".
Matt, you know what 1+ hr video from you is called?! A Gearheads treat! Your art to refurb is second to none, thanks a lot!
Exactly! Matt, never worry about how long your videos are, you have a very captive audience.
Matt, I want to commend you on your videography. Your camera angles and editing skills are next level IMHO. You show us everything we want to see and then some. No wonder your channel is doing so well. You keep making videos like this and I'll be watching them well into my twilight years. Thanks so much for the great content.
I agree this was my first video of his and I though it was awesome
It's an oldie but a goodie, you got a good deal
I'd love to see the top speed. I'm guessing 48 mph!
50 does sound about right, he'll need an entire crew to effectively use all his machines at a job site
He might be able to score some extra cash that way like Chris at letsdig18 or the folks at Dirt Perfect do
I would probably say 65 mph. I drove a 67 back in 67 lol, I am old
The one I drove 65 mph no governer
I drove one with out the dump bed it ran 65 mph without pushing it.
Speedometer says 80 🤷🏼♂️🤣
That definitely is money well spent , the frame and under carriage looks awesome and the Engine sounds mint! I think that a good name for the truck is "Die Hard"
needsa cammo paint job on all rigs he got
@@rsprockets7846 no 💀
Done a great job, sound good. I enjoyed, thank you.
Matt, what I love about your videos is the fact that I can go away from you for a while and then come back and it’s the same caliber of educational, entertaining, and just plain enjoyable to watch videos.
Thanks.
Nothing makes me smile as much as seeing someone give an old neglected machine
some love. The junk we as a society build today will never ever be around as long
as the machines built by our fathers and grandfathers . Great respect from canada.
Hi Matt I am 75 years old and live in the UK.I have watched your video’s from day one and I have loved them all but this one was such a pleasure to watch.That International seems to be a quality build and designed for easier maintenance.She deserves a bit of tlc
over one hour of video definitly worth the wait! love all your videos
Glad you like them!
@@DieselCreek great job on the IH must be an old state DOT truck, ever figure out a standard paint job on all your equipment?
@@rsprockets7846 I thought that too, kinda like MattsOffRoadRecovery yellow. Would be neat to see a standard.
@@dubuque1 He does have a nice yellow Christine!
@@leeklemetti1887 Yep. Can't wait to see that grader back together and with glass and rubber in the cab.
I can’t believe I just discovered that diesel creek did a video on my favourite truck
I worked at a parts store in Fort Fairfield Maine from 1988 to 1992 that used to be an International dealership in the 60's & 70's. It was a town of about 4000 people, but had a LOT of potato farmers. In 1965 they sold 100 Loadstar 1600s! Many were still in use 28 years later.
Can you do an update on the church/apartment you were working on? We love your videos!
Nice job as always Matt. If you can I would keep the loadstar as part of your fleet.
Looks like that fuel tank has been replaced not to long ago , that's a win win , stay safe , from the UK ...
Highly impressed with you firing the old girl up I remember those trucks in Baltimore growing up City was yellow and the water works department was light blue Those colors are still used to this day
I found myself with a big smile on my face as I watched you driving down the lane. What a great find and a great buy.
Those IH gasser’s are pretty good engines. They are very resilient and tolerant of abuse.
Perfect for a work truck
Back in the day international was working man's truck strong truck easy to work on construction truck thanks for sharing
Old reddy is a good name. Because it's so awesome!! Keep the dump truck it's great!! Absolutely worth it.
I grew up driving and fixing loadstars. That's gotta be a two speed rear I've never seen a ten speed. That big holley four barrel means its a 392. These trucks are bulletproof. They're hard to break and easy to fix. We always called them cornbinders.
Yes, this is a 5 speed transmission with a 2 speed rear axle. 2 speeds are accomplished with a set of planetary gears and a sliding clutch that either allows the planetary set to rotate on itself for reduction, or lock them all together as a unit for no reduction. The need to split shift (or not) depends on load and grade. Lightly loaded and slight or no uphill grade and your engine will "probably" handle the upshift without problem and continue to accelerate. But if you are loaded heavy or steep uphill grade it's best to split the rear end to high while staying in the same transmission gear to give the engine a bit of help staying within its better pulling range. Next upshift you pop the rear end back into reduction while simultaneously upshifting the transmission to the next taller gear.
Compound box transmissions are different. With compound box transmissions you upshift to the highest ratio and then shift the compound box to the high side and repeat the transmission upshift sequence all over again.
Drove many corn binders In 45 years of truckin ,mostly COE
Our old fire tanker was 64 loadstar 1500 gal. 392 was cold blooded. Fun to drive. Hard to stop.
Today I was looking thru one of my 1970 tool boxes and found a two speed motor. I laugh 😂
What model of loadstar is it. I have a 1700 all original and trying to find parts for it or manuals have become a nightmare. Any info would help greatly
Hi, Matt. just what I need today, on a cold April's day in Berlin. love this truck..
If you run out of fuel at around a 1/4 tank mark it's because the pickup tube filter is holding the pickup tube up off the bottom. You can take the pickup tube back off push the filter further up on the tube and that will fix that. Just ask me how I know lol. Nice job love these old trucks 👍🏻
10/17/2023 Matt has a beautiful shop now ! Congratulations and the Philadelphia Phillies baby!!!!
You should add a “will it burn” segment to any future “will it run” videos! I think you’re like a lot of us that LIKE 🔥! (But don’t catch anything good on fire like the ratchet strap on your service truck)
I would love to see a wash, oil change, and a new cover for the seat.
I will never argue the time it takes or the cost to of a mechanic again, that takes some patience
Your content is good and makes men from the city feel like they are loosing out on good 'ol guy stuff.
The "ol binder" is pretty impressive! Back in the day, they were a solid work horse truck. Definitely a very good score.
Dear Matt: I can see that your site is an amazing place, when, just hours after posting, you have 10k+ thumbs up and over 1200 comments. I, like so many others, really enjoyed this hour long video. Thanks so much.
Looks like a "Rosey" to me! Dad bought my Mom a special farm to market truck in the middle 60s- a Loadstar 1600. I recently discovered a 75 loadstar 1700 and rehabbed it- named it after Mom!
I am a retired truck mechanic and an IH guy even worked as a truck mechanic in an I H truck dealer when I was a pup, those were great trucks IH sold a bunch of them I had a 1964 loadstar 1600 I used as a mechanic service truck for 18 years. I took in a lot of money in my mobile fleet repair service with that truck I did not have much problem with it.
Lube the door hinges real well, before they break off. Top speed depended on the person paying the bills.
Definitely brought back a lot of memories for me seeing and hearing this truck run. I grew up on the other side of PA from you, my grandfather had a building materials business, and he had a few International truck, an Autocar, and a Mack. One of the International trucks was exactly the same truck just blue in color. I started driving that truck at 16 delivering sand, stone and coal.
في اي عام ذلك
Matt you could call your International The Binder, as that was the nick name for Internationals among truckers in past decades. It was a reference to Cyrus McCormick's nineteenth century field implement.
Matt: I forgot to mention that the 4-barrel carb on your truck points to a possibility that the engine is a 392 rather than a 345. There is a machined area on the right-hand front corner of the block, just below and behind the alternator that specifies the displacement (naturally, it will be hugely greasy and dirty, so you will have to scrape and wipe it before you can read it. The 345 is powerful; the 392 is immensely powerful (but it burns more fuel than the 345). You will come to love whichever one that you have, and you will probably decide to slowly restore the truck. It will probably become your family's prized possession.
Yeah, I'm an IH guy. At this point, my IH stable is small again. I have a beautiful '67 Loadstar 1600 flat bed (345, 4 and 2), an award winning restored '73 Scout (5 firsts and I second in six shows), and a 464 tractor (1300 hours) much like your 454. I'm looking for a '70 1200 pickup to replace the one that I foolishly sold in '78. Also looking for a '67 Travelall to replace the one that a huge deer destroyed in '04. As I mentioned, I'm an IH guy.
Yep it’s Otis 4 barrel it’s not a 345
They were all two barrels
Otis ??? Hate spell right
@@philliphall5198 Yeah. "Otis" doesn't make sense there. Should that be, "Yep, if it's a four barrel, it's not a 345"?
May have what you're looking for...
Matt those load stars were used for many years in many ways, from school buses, fire trucks, delivery, and dump trucks! You have a good running gem there!
That's a great looking old International, at least in terms of style! Glad you got the old girl running, seems like she might serve you well over the long haul.
Gas powered Internationals like that one were what the school buses I rode on in Elementary school were built on. I'll never forget the sound of the driver working the gears, especially on hills.
My ex. used to be taking those carboraters apart on the kiitchen table. I would be complaining because I wasn't able to serve dinner until he was done. He had a really big one, a double barreled carborator , trying to clean it one day. Its so nice we don;t have to worry about carboraters any more.
Those old truck bring back memories… My uncle had one very similar… and Carb rebuild… I saw enough of those by the time I was 10 to last my lifetime.. my father was always rebuilding someones…
I just watched this whole video without skipping a single bit. I regret nothing. Matt makes some quality content. It really helped pass the time. I was sitting in class bored out of my mind.
BIDEN 2020 ALL THE WAY BABY
@@evan_kumar wonder why hmmm
@@evan_kumarI hope you're happy with your grandpa Biden now.
you really do have a touch for getting these old school boys and girls going again. giving them another chance to prove themselves worthy. great job Matt.👍👍👍
When my dad was teaching me how to rebuild a carburetor, he told me to check the floats to see if they need to be replaced, just squeeze them with a pair of pliers. Then put the new ones in.
Why would anyone consign a potentially good vehicle to the scrap heap?? You can tell the old truck WANTS to be yours Matt, it's doing everything it can to live again and be yours alone :-))))) I wish it were mine, $500 is a steal. I really enjoy your videos and your company, always a joy. Cheers from Wales.
Given the age of the dump I would urge you to replace the brake softlines. Nothing worse than having a load and a popped soft line.
The two speed axle is great for when the truck is loaded. Start off in "granny" (1st) gear with the button in the down position. Gain a little speed and RPMs then push in the clutch and pull up on the button leaving the truck shifter in the 1st gear position. (Now you have split the gears between 1st and 2nd). Gain a little more speed and RPMs then clutch and shift into 2nd gear pushing the button back into the down position at the same time. Gain a little more speed and RPMs, push in the clutch and pull up on the button and release the clutch. You are now between 2nd and 3rd. You can continue that method until you have gone all the way to 5th gear in reality giving you 10 gears. You can also leave the button in the down position and go through all 5 gears and pull the button up when you have traveled the full range of 5th gear low side. Pull the button up and you will be on the high side of 5th gear.
I hope this information is helpful to you. I certainly enjoyed watching you get the old girl running. I am really impressed with your capabilities. Thanks for the good videos I really enjoy them.
youre going to have a bad day if you shift from 5th low range to 1st high range.. engine will see 12,000 rpms before a rod leaves the block
@@AndrewBrowner Not what he said, I don't think.
@@AndrewBrowner Who said anything about shifting from 5th low to 1st high? Reread and understand before making a comment!
@@TKevinBlanc You are correct Kevin, that is NOT what I said.
IIRC a Loadstar Can be compound 5, so you can have a case of missed geared at the top, cause depending on box, it should go 1Lo, 1Hi, 2Lo, 2Hi, 3Lo, 3hi, 4Lo, 5lo, 4Hi and 5hi, with the option of leaving 5lo out, because it being so close between the gears.
And after I started remembering things; there was a 3 boxes available, 5direct, 5compound and 5OD.
And the 5 OD being rare, above that there was 3 Roadranger style transmission, where the 2 biggest was in the Non-butterfly hood, and one of those two was behind the DD v6.
I love Loadstars, but DD puts the tits in trucking!!
Love that little truck too. When I was a kid I drove them with a potato box for harvest brings back good memories thank you
Bring memories from my childhood. They still around, with turbo diesel engines and synchromesh transmissions... going for other 30 or 40 years more of service.
Brings back memories. I revived a 1968 IH Loadstar and loved that truck. Factory was a straight 6 but converted it to a v8. So easy to work on. Mine was $600 and had lots of the same issues. My brakes were vacuum assist though.
If you find yourself in need of a clutch or brake shoes, do yourself a favor and take them directly to a remanufacturer. Saved me a TON of money.
Matt I have been a subscriber for a couple of years. I really like your enthusiastic approach to these old iron projects. Your no fear of attacking the seemingly difficult issues is inspiring. Thanks for keeping your channel growing.
My uncle owned a massive dairy operation in southern Utah. All his gas powered trucks were IH. Ten ton hay bale trucks, huge dump trucks to haul away cow manure by the ton, all were IH.
The shots you get for your videos is impecable 👏🏼👏🏼👏🏼
One moment of clarity in this crazy time thanks for the new video Matt!
You got it!
Hey Matt, I’ve found that when cleaning really gunky carbs and other parts that a good quality oven cleaner (spray can) works pretty good. Use a mask and gloves but it will clean down to bare metal.
Also I’ve discovered a way to solder that pin hole in the float with out overheating the whole float. Submerse it in water with the “blow hole” up. It will keep the rest of the float from unsoldering. Maybe you already know but just in case!!
Thanks for your great videos. 👍
the oven cleaner eats aluminum and leave it looking like crap just a heads up
Most oven cleaners are lye based and quite aggressive on bare metals. Ovens are porcelain can resist the effects of corrosives pretty well.
@@smasica Yup yup, i believe easy off makes an aluminum one tho
@@beettheyeetskreet9216 Good to know. Thanks. My mother used Easy Off for years, both the old brush on paste and the spray. Strong stuff.
I love these old dump trucks, we've got a GMC c6000 that runs great but the brakes just will not tighten up. no leaks, just no pressure, changed almost everything in the whole system, same thing, so aggravating. I love the 2 speed rear end, people always try and buy it off us
One of my favorite gas powered trucks! I would highly advise that EVERYTHING be dismantled before dipping in carb cleaner though! The big Holly needed a bath and probably new accelerator pump too! Thank you for reviving a LoadStar!
Dean Benson , You might want to explain what carb cleaner does because he used brake cleaner. Ouch.
Love it Matt! 1972 bought my first truck. A 62 loadstar 1800 with a totally worn out 345 v8. Super simple to work on. Everything is accessible. Keep your eyes open for same truck with air brakes so you can change over from juice to air. I've done it on an old tandem. Old truck even had foot valve to fit on firewall. Thanks for the memories!
Sweet sounding motor, a very good buy for $500.
That brings back memories. Back in the late 70s we had a 1967 IH truck with a big grain dump bed on it, bought at auction. It replaced a 1936 Chevy that definitely needed replacing by then. I put some miles on that thing.
Like an old movie star that will not fade away... "Scarlett!"
That’s a cool truck. I agree the styling is timeless. Would really look great with a fresh coat of black paint on the body & red on the cab. Clean it up & get years of service from it. 👍
Hi Matt, I am 68 today and it's pissing down with rain outside as usual, you've made my day with your video, keep them coming, cheers from the UK.
Happy Birthday!
Happy Birthday! 🙂👍
All the best. I am turning 70
Happs! Many more.
@@georgedavidson1221 The best is yet to come George... I think🤔
Sure is good to see the no-nonsense approach to fixing things. Good filming and excellent commentary Matt. 👍
Years ago, I tried rebuild a 2 barrel carb on a '57 Chevy I had. 3 people helped tear it down, but I was alone to reassemble. After 2 hours, i got the top back on the carb, traded it on a rebuilt carb.
Great revival! That thing is minty. IH gasser lubrication systems are more about flow volume than pressure. Discard the notion of seeing 70-80 psi like you may be use to with other engine makes. A steady 10psi per thousand engine revs at operating temp is plenty good for the ol' Binder. So at hot idle, that can be 10 psi or a fuzz under and still be just fine, as long as it jumps back up with a throttle blip. But yes, some quality 15w-40 diesel rated oil will be just what the doctor ordered. These engines are overbuilt in nearly every way, but they do have an achilles heal...the cam bearings. Sitting non-rotated for many years does them no favors. Keep an eye on that OP gauge and an ear trained on the valve train. If you start seeing erratic gauge readings during extended intervals at higher revs, accompanied by lifter clatter, your cam bearings have likely given up the ghost. But, for how you intend to use it, that time could well be years away yet.
Diesel oil is not good for gas engines as it has detergents in it like trans fluid and can wash down the cylinders and bearings
@@masterbates7016 If that was true, it would be just as harmful for a diesel engine. Many folks have run diesel rated oil in gas engines for decades with no ill effect. Older flat tappet gassers like the one in this dump truck need a certain amount of ZDDP to prevent premature cam lobe wear. That ZDDP level is no longer sufficient in modern conventional motor oils due to supposed damage to catalytic converts. Diesel rigs don't have cats, thus the ZDDP level remains sufficient.
@@masterbates7016 Don't tell Vice Grip Garage that ;) And I use the same stuff (15W-40 diesel flavor) in my air-cooled garden tractors and it works great! Zero oil consumption now and it stays clean for 2+ seasons of use.
@@masterbates7016 I have ran Shell Rotella T4 15w-40 in gas engines for over 25 years. They all do fine. Still use it in my 345 V8 pickup and my 300 6 cyl Ford.
I've owned a few IH V-8 engines. I can confirm the cam bearing problem. Take off the oil pan and there will be thin sheets of bearing babbitt metal in the bottom of the oil pan. Also the engine times on #8 cylinder (closest to the passenger firewall). Russ
Once again: Matt: I just liked the look of this and wanna save it; I'm not gonna KEEP it or anything....
Also Matt: Man! I really love this little truck, it's great! It'll be so handy to have around for projects and stuff!
Spoken like a true collector.
IH was always very good at using good steel so severe corrosion on fastners and moving parts is usually not terrible. Body panels are a different story.
If you can find the line set ticket it will have a list of all the parts that were on the truck when new. It's a piece of cardstock usually in thr glove box or attached to a inner rear corner of the cab. It might still be there. If not, Five Star Trucks in Lewiston, PA told me several years ago that they could get copies of your line set ticket based on your VIN number, might check with them.
I found a 53 international sitting in a double corn crib underroof. 1 ton duals. I hauled firewood on it for 10 years. Had more pulling power with weight than my tractor, geared low. 50 mph and the straight six was winding.. used it up to 1990. And sold it,
this brought back memories of when i was young pretending to drive one just like that that had been sitting, wish my grandpa didnt scrap it. all thats left now is the badge on the shelf
I love the old IH's my grandfather had a rollback about the same year and I loved to drive it even though I'm a Chevy guy,,, I'd call it "Big Red" . I love the video 👍👍
Hey Matt I really enjoy your videos! Try using Lacquer Thinner in the gas tank. It dissolves the varnish and you will be shocked how well it works.
Second that!
Add some clean crushed gravel and you will be surprised what it removes. 👍😉
I'm from 'DOWN-UNDER'/Aussie; A name suggestion with me for this Inter might be, The 'Appoloussa' then with a clear coat as its protection, your Inter could stay with 'APPOLOUSSA'! So, then Matt Giddy-Up!? 👍Keep-On🚛
I've got a 1979 C70 Chevrolet dump truck same size as this International. I call her "Old Blue". I've been running this truck for almost 20 years and use it regularly. My top speed is 52 miles an hour before the overrev light comes on. The one thing that is definitely on my list to change is to upgrade from that nasty cast iron single Master cylinder brake system to a hydroboost. Have lost the brakes twice when fully loaded and there is absolutely no stopping until you simply run out of inertia. One was a vacuum can failure and the other was a blown brake line. We have the advantage here of no hills which helps with the lack of performance. I have a 366 gas with 5+2 tranny. When I bought the truck it had a golden dog hood ornament that someone had installed on it and I was gonna take it off. It's still there all these years later cuz performance wise it's a dog, but dependability wise it's golden!!!
When you were reversing it sounded just like my old Morris Minor did in reverse, because it had straight cut reverse gears. Still worth checking I guess, but it might be nothing to worry about.
I think you'd be hard pressed to find a bevel cut reverse gear in a truck transmission in those days, they all had a good whine from what I remember.
@@thekeyboardwarrior5054 Yes, that was kind of what I was thinking. Here in Europe things are different in many ways, but commercial vehicles tended to go for the strongest option than any level of refinement!
@@IanSlothieRolfe I think the same for here as well, It's been a long while since I pulled one apart, ans I'm no expert, but if I recall correctly, reverse used 1st gear, which was also was straight cut and with no synchro, it being a couple of smaller gears turning a big one, which is why all the noise comes from.
"Buella" for a name. Love the old Loadstars. There were lots them around 40-50 years ago. Always either dark green, red or highway yellow in my area. Great trucks, they just look "right" to me. Sure wish I could run onto one like that!
Buelah! I second this. Like the teacher from Porky's
Matt - you are the first person I have ever heard say that a Corn Binder steered and handled really well..
Matt, you did an excellent job at rebuilding the carburetor and adjusting it, too!
You made an great investment in the dumptruck which I think you "should name Jasmine."
Well done, Matt!
Are you going to have to take the fuel tank out to replace that filter when it clogs? You know that it is going to clog. You might have been better off to have just put the tube back into the tank with no filter on the pick up. Just put a good see through filter in a external place along the fuel line "before the pump" that you can see and get to easy. That way you know that you never would have to pull the tank and you have a good in line filter elsewhere that will do a better job and can be easily changed.
Your right, that is a rather limited surface area filter. Maybe a screen could have been a better choice for that location.
Man I've been looking for a find like that for years only dreams at this point you're a lucky man
How I love to start my Saturday, after making my wife's breakfast and lunch, with a video like this.
I almost want to quit my job and become a carb' repairer!
Well, maybe not, but this was another great one.
Thanks from Japan.
Nice find, those old Internationals are tough as nails. I had a 68 Loadstar 1800 dump truck w/345 eng, 5 & 2 axle, air brakes 75,000mi (ex gov truck). It had a very short 134" WB with a 9' Truckweld 4/5 yd box and it turned on a dime but if the driver took their eyes off the road it wanted to drive right into the ditch.
Hey from Philly, love your videos man! Between you and Camarata I can’t get enough, need you guys to work out a rotation so we get vids daily! Haha
Here in northern Indiana, I see a lot of these old Loadstars sitting on farms (mostly with grain beds, of course), and they seem to be ready for at least seasonal use at their advanced ages. They just don't build them like they used to. Glad to see yours running so well!
Just too small for most farms is why they sit. Most guys around here use them for hauling spray and liquids to their large equipment. A hundred acres was enough for a family in the fifties. Now it takes more than a thousand.
A good old truck. I use to drive one back in the 70's.
Hello, my friend,
Coming to you from a small town in Ct. Just want you to know that I have been a Mechanic for some 50 years working on cars trucks and my favorite Johnson and Evinrude out Board Motors I LOVE WATCHING YOUR VIDEO
Those are great old trucks. My first non farming related job as a teen was working as a grave digger and the guy I worked for had a single axle international like that. It wasn't fast, it wasn't overly powerful and it used a ton of gas, but everything about that truck oozed strength and dependability. It was a purpose built machine and was a pleasure to use. I actually keep my eyes open for one still, and would buy one in a heartbeat if I could find one that wasn't rusted away. It is definitely a 60's design era forefather of the truck you run now. With a little road time you will find that two speed rear axle natural and easy to shift. The only thing I would change about your truck is to shoot a coat of industrial yellow on it, cause that's how I remember them fondly 🙂
A new Diesel Creek video. Nice! Makes my day.
Glad to hear it!
Variable resistor. As the fuel float moves the resistance changes changing the location of the pointer on the gas gage.
Check the radio on that old truck Matt. Also make her roadworthy because L'll bet some day need to use the highway, brakes and brakelights headlights etc. Consider putting a paint job on the old gal and new boards on the sides with Diesel Creek on them.
Good old truck Matt, remember time off #8 and keep a screwdriver handy when the point close up. Adjusting the brakes, makes a big difference in the pedal height . Make sure to remove the drive axel breather and make sure it is clean of rust they fill up internally and this will prevent possible axle seal leaks. Glad to see your not afraid of carbs like most young guys today!
Congratulations, Matt - great job on getting it running. I remember these well from my childhood in the 70s - I always liked the look. It's a sweet ride - I think you should keep it!
Dad had some 60's models of this exact truck, as well as Fords, GMC's and Chevys. All used in his asphalt business. They got snow plows added as well, never got to drive one, but ran the plows up and down /w the drivers permission...on snowy snowy nights, in big parking lots.
I love those old cornbinders (IH) and that IH engine is a brute for work. My first thought was to call it Ole' Red as soon as the video began. I already named it for you. LOL