Magic Controller Sensorless Mode - Golden Motor Canada

A demonstration of our Magic Controller in sensor and sensor-less mode.
goldenmotor.bike/product-cate...
To view our extensive product selection, visit our website at: goldenmotor.bike/shop/
Like us on Facebook: / goldenmotor.bike
Follow us on Instagram: / goldenmotor.bike
For exclusive deals on our products, join our owners clubs at: / 140989196674135
Subscribe to Golden Motor on CZcams: / goldenmotorcanada

[@MrNigel1340]

Thank you for the information, this has helped immensely.

[@mackattack8627]

Great

[@sgas]

cool comparison

[@noearias2006]

❤ THERE ARE ONLY TWO VIDEOS OF HOW TO CONNECT MOTORS WITHOUT HALL SENSOR BUT NEVER SHOW HOW TO CONNECT THROTTLE , AND NEVER SAID WHICH ARE SELF STUDY WIRES 🇺🇸❤🛴 THANK YOU FOR YOUR VIDEO

[@pietromazzettidipietralata4281]

hi, any idea to have display ( dashboard ) for this controller ? ciao

[@jeramyeswan4014]

My ebike goes up to only 20kmph. Wanted to see if it will increase in speed if I disconnect the hall sensor.

[@raymondreeves4477]

Thank you, great video. Do they make these hall sensorless controllers, for 72 volt 3000 watt motors? I need a replacement, And I'm not sure, if it's the charge controller, or the hall sensors in the motor. I live down in Arizona USA. Thank you so much.

[@chnapo1]

Is there a way to set up the 50A Magic controller so that throttle controls power instead of RPM? Right now my bike will, if I use half throttle, accelerate to half speed with full power. It is a small wheel and therefore has very high torque, almost impossible to start without wheelspin.

[@SteveDBallantyne]

Hello Gary, is there a controller setting on a VEC series that allows you to bypass the hall sensors? I have been running the 5Kw 72v motor with a VEC 300 controller. Occasionally (usually when it's wet outside) I will step on the throttle to pull away and there is a *JOLT*, and then I lose all power. If I put my foot out the door and push the car forward while hitting the throttle, I can pull away. Seems like a hall sensor? Just wondering if I can remove the hall from the equation using the controller USB programming software.

[@goldenmotorNA]

Hi, that is more of a question for our forum at www.goldenmotor.com/SMF

[@maukaman]

Is this a common form factor for motor controllers? I have one that looks exactly the same from a mart cart. It has only 2 phase wires with terminals but the label has 3 phases listed, one seems to just be missing the terminal. Is it possible that this controller could be modified to run a 3 phase brushless motor?

[@danielbutcher3305]

Hi there,
I have been looking for an answer to my issue for a long time. My controller states it is dual mode. I was running my wheel with the HAL sensors and they suddenly failed exactly like this wheel. But when I tried it with only the phase wires connected the wheel didn't turn. There was just a quiet clicking sound each time I turned the throttle. I've had 3 wheel hubs. Each time they failed on me. I just want to run without the sensors. Should I buy another controller?

[@azertaieb442]

This controller is sensorless and about the second wheel test ..if you check the angle of the controller and the hall in motor you will see that is not the same ...thank you for the video ...i hope that you send to me the lik of this controller ...thank you again

[@AlizadehMa]

Hi, I have a motor with only 3 hall sensor cable! but my controller has 6 :-) what will jo suggest :-)

[@MiMi-fh7ul]

Hi where can buy one thanks

[@gerardogama120769]

Does that controller work fine with a 72 volt battery 3000 watt motor?

[@goldenmotorNA]

No it will not fit 72 3k you will need the following controller
goldenmotor.bike/product/vector-200-series-72-volt-brushless-motor-controller/

[@gerardogama120769]

@@goldenmotorNA but the issues with the motor wheel are the sensors!! So I'm looking for a sensor less controller compatible!