Nissan Mass Air Flow (MAF) P1102 Diagnosis and Replacement 2003 Altima 2.5 (2002-2006 Similar)
Vložit
- čas přidán 20. 10. 2017
- In this video I show you how I troubleshoot and replace a Mass Air Flow (MAF) sensor on a 2003 Nissan Altima. This vehicle idled poorly and eventually had a P1102 check engine light. Although I used a more expensive scope in this video, there are cheaper alternatives that can be used like a DSO Nano or similar product from AES Wave.
The exact vehicle in this video is a 2003 Nissan Altima 2.5S four cylinder with automatic transmission.
Be sure to subscribe for more tool and car repair videos!
/ bigdog50001
/ bigdog50001
/ bigdog50001
Disclosure: This channel earns a small commission using some of these links - at no additional cost to you.
The Big Dog 50001 Automotive Channel Store can be found here: www.amazon.com/shop/bigdog500...
Tools and Parts:
Mass Air Flow (MAF) Sensor: amzn.to/2LpNYOd
AESWave uScope: bit.ly/2lD1Z1C
Alternative DIY Scope: amzn.to/2MXsFXs
Snap-On Vantage Ultra: bit.ly/2qqO4et
Autel MS906BT (Upgraded Version): amzn.to/2zTecDo
208 Piece 1/4" Bit Set (Alternate Version): amzn.to/2Lv5Kzp
Want a free Big Dog50001 Automotive sticker? Send an email to bigdog50001@gmail.com with your address. Sorry, no international addresses.
Have something you would like to send to Big Dog50001?
Send it here:
Big Dog50001 Automotive Channel
P.O. Box 726
Cortaro, AZ 85652
2017 Epidemic Entertainment. All rights reserved.
Disclaimer:
Due to factors beyond the control of the Big Dog50001 Automotive Channel, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. The Big Dog50001 Automotive Channel assumes no liability for property damage or injury incurred as a result of any of the information contained in this video.
The Big Dog50001 Automotive Channel recommends safe practices when working with power tools, in on or around automobiles or other vehicles, automotive lifts, lifting tools, jack stands, electrical equipment, automotive modules and systems, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.
Due to factors beyond the control of the Big Dog50001 Automotive Channel, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not the Big Dog50001 Automotive Channel. - Auta a dopravní prostředky
*Parts and Tools*
This channel earns a small commission using some of these links - at no additional cost to you.
Mass Air Flow (MAF) Sensor: amzn.to/2LpNYOd
AESWave uScope: bit.ly/2lD1Z1C
Alternative DIY Scope: amzn.to/2MXsFXs
Snap-On Vantage Ultra: bit.ly/2qqO4et
Autel MS906BT (Upgraded Version): amzn.to/2zTecDo
208 Piece 1/4" Bit Set (Alternate Version): amzn.to/2Lv5Kzp
The Big Dog 50001 Automotive Channel Store can be found here: www.amazon.com/shop/bigdog50001automotive
Be sure to subscribe for more tool and car repair videos!
czcams.com/users/BigDog50001
twitter.com/BigDog50001
instagram.com/bigdog50001/
Disclosure: This channel earns a small commission using some of these links - at no additional cost to you.
The Big Dog 50001 Automotive Channel Store can be found here: www.amazon.com/shop/bigdog50001automotive
Great diagnosis . I'm going to send you one of my channel stickers 👍
Thanks, I will be on the lookout for it!
good video and explanation! and nice sticker I saw behind the whiteboard!
Thanks! Yeah I can't quite remember where I got that sticker from.....
The Disgruntled Mechanic 😂😂😂😂
You should become an instructor at the local Tech School. This is an excellent tutorial Dave.
Thanks Rob! I appreciate the comment!
Thank you very much, very informative 🤙🏽 Mahalo
I appreciate the comment, thanks!
What hose connects to that maf sensor ? I’m trying to replace that but I don’t know the name of it.
exelent job no questions ask
Very good explanation and demonstration appreciate it thanks 💐
You bet , thanks for watching 👍!
How do u get it out of the mode where it won’t pass 3 rpm
Great Video
I have the same vehicle and I ran all the tests for each wire, but when I rev the rpm up to 2500 and 3000, it never gets past 1.97 volts. Should it not get to 2.5 volts at 2500 - 3000 rpm? Should I change it to a new one?
I have a 2003 as well. I’ve been having issues with my car slipping out of gear going neutral while I’m driving and idle up to 3500 rpm and then it will pop back in gear sometimes and start back riding,then sometimes it won’t.. I have to pull over and cut it off and sit for about 2 minutes or so then it starts driving. What do u think it could be? It was reading spend sensor codes so I bought 2 of those and it was saying idle sensor too high so I bout the throttle because the sensor didn’t come separate,come to find it out I didn’t need that because the car is still doing the same thing. I have spent about $500 in sensors and nothing is helping.I was told the transmission was going out and then I heard it wasn’t because spite all of that,it switches out like it supposed to when it’s acting right.
Not sure if you could provide some advice on this but I figure I'd try: I have a 2011 Altima that has had its Check Engine Light on for some time now. The code is the p0101 code. So I've had the mass air flow sensor replaced five months ago, but the light is still on. I have the ECM reflashed and after a week it came back on. Finally, it turns out my car was part of a recall for getting the ECM upgraded. My mechanic took it to the dealer, got the upgrade, and the light had been off for the past month until yesterday where the light is now back on. Any advice or answers???
I've read things online about cleaning the throttle body and that took care of it or checking the hoses for leaks. Could it be a problem like that? Or is the computer really in need to constant reprogramming? I will say that when I drive the car the car drives fine but I have noticed that since the dealer upgraded the computer a month ago, the RPMs upon acceleration is pretty even at 1000. But when the Check Engine Light is on, when I accelerate the RPMs go higher now before the CVT kicks in.
thanks...good video
I am a technical trainer for a truck repair company and I wanted to say that you did an excellent job of explaining the test procedures for this sensor. I have a couple of questions.
How do you feel about the Autel scan tool vs Snapon's?
I have the Modis Ultra which includes a two channel scope. Do you prefer to have your scope separate from your scan tool?
Thanks
Thanks for the comment! Snap-On makes great scan tools and you can't go wrong with one but the Autel is much cheaper and I think can hold its own. I work on a lot of Hondas and the Autel replicates the Honda HDS pretty well which is why I prefer it. I do like having a scope separate from my scan tool so I can see both at same time.
This is very good video
Thanks 👍!
Did he have to unplug the battery before installing the new one? I saw another video that the mechanic said take off the negative wire to battery so u dont pop the sensor when u plug the new one in. I need to do mine because of a prolonged start after time. At least 3/4 seconds before if fires up. And some times stalls out when starting. Any advice?
No need to disconnect battery, just have to make sure the key is off.
Suggest a good place to buy Nissan parts online
Thank you Sir. Good job. I appreciate your videos.
Thanks!
How many gs should I. see at idle for a versa 2018 . I have 1.7to 1.9 GS @ idle
For those Versas, it can very from .8 - 4.0 g/s at idle (warmed up engine), just depends on the location you are at. Good chance those readings are ok.
Thank you for this wonderful video!That video was perfect for me since I own a 2003 Altima.Do you teach a class somewhere?
I only teach here on CZcams lol. Thanks for the comment!
anyone know the exact size to security bit ?
If you are referring to the Torx security bit size for this vehicle, 6:17 in video, TS25.
Thank you very much … I bought a little cheap set (harbor freight ) and seems the inside hole isn't big enough .. Ill buy a higher quality one... Great Video !! Wish you had an buick enclave .. We'd be best pals ..lol
T25 Security doesnt fit on mine. I went to several parts stores and nobody had the bit to take mine off. I noticed that on mine i only have 5 star with the security piece in the center. And the t25 bits have a 6 star with security. WHat i had to do was use a small pair of vice to loosen and get the bolts out. So just beware before you buy a set to check if you have 5 star or 6 star. Also if you have one like the video which is t25 and you go buy a cheap set at Autozone, or harbor freight be sure to look at the bits in the package. Most i have found are very cheaply made and the security holes on the bits are not centered. So even if you did get the right bit it still might not fit due to poor quality of the bit made.
Why my Nissan won’t start after I replaced it?
Did the car start before replacing it? A bad sensor can sometimes cause it to not start, these Nissans do not have the best backup strategies if the sensor has failed and sometimes aftermarket sensors do not work well.
thanks
👍