2006-2011 Honda Civic Wheel Bearing Replacement (Without Removing the Spindle)
Vložit
- čas přidán 30. 07. 2024
- On this episode I show you how to replace your front wheel bearing on your 2006 to 2011 Honda Civic. The procedure involves removing the brakes and pressing the old bearing out of the knuckle and pressing the new one into the knuckle. The only way to remove the bearing on the vehicle is with a couple special tools that I go over how to use in the video. I would estimate probably 3 to 4 hours to replace these bearings if you're not familiar with the procedure.
Here are the parts and tools you will need to replace your Honda Civic's wheel bearing:
Tools:
Slide Hammer: amzn.to/2X6CEdS
Press Tool: amzn.to/2UGbb6p
Large Snap Ring Pliers: amzn.to/2UZKE33
Impact Driver: amzn.to/2X5pj5M
Parts:
Bearing (non SI): amzn.to/2X4SWnE
Bearing (SI): amzn.to/2P86ZpX
Snap Ring (non SI): amzn.to/2PRj4jr
Snap Ring (SI): amzn.to/2DfOESS
Hub (non SI): amzn.to/2XcZfpj
Hub (SI): amzn.to/2Xa2iOX
Help support the channel by using my Amazon links
As an Amazon Associate I earn from qualifying purchases.
Torque Specs:
www.collegehillshonda.com/ins...
Questions? Shoot me an email at repairgeek365@gmail.com
Disclaimer:
The information, demonstration and any content contained in this video is for informational purposes only. The user Repair Geek makes no warranty, express or implied, regarding the effectiveness or safety of the contents of this video. In no way should the contents of the video, including the tools used, be repeated or tried by anyone. Viewers should only seek the help of a trained professional located at a licensed auto repair shop for any fix, modification, alteration, or any change to their vehicle. Repair Geek shall not be liable for any injury, damage, or loss to any person or property that may result from use of the tools, equipment, or any content contained in this video. In addition, there is no way to guarantee that the video is not altered or modified or is not in the final form submitted by Repair Geek and therefore, Repair Geek does not warrant that the video is unaltered or not modified. The links on this video to products are for informational purposes only and in no way are an endorsement of the safety or effectiveness of the particular product. Viewers understand that anything contained in this video or linked to or from this video is the sole responsibility of the viewer and in no way provides an express or implied warranty as to the safety or effectiveness of any linked tool, product, or video. Therefore, viewer agrees to release, waive, and discharge Repair Geek or anyone affiliated with Repair Geek, from any and all liability, claims, demands, actions, and causes of action whatsoever arising out of or related to any loss, damage, or injury, including death, that may be sustained by the viewer, or to any property belonging to viewer, regardless of whether the loss is linked to the use of the contents of this video, or otherwise and regardless of whether such liability arises in tort, contract, strict liability, or otherwise, to the fullest extent allowed by law. - Auta a dopravní prostředky
Here are some links to the parts and the tools that I used in the video:
Slide Hammer: amzn.to/2X6CEdS
Press Tool: amzn.to/2UGbb6p
Large Snap Ring Pliers: amzn.to/2UZKE33
Parts:
Bearing (non SI): amzn.to/2X4SWnE
Bearing (SI): amzn.to/2P86ZpX
Snap Ring (non SI):amzn.to/2PRj4jr
Snap Ring (SI): amzn.to/2DfOESS
Hub (non SI): amzn.to/2XcZfpj
Hub (SI): amzn.to/2Xa2iOX
Help support the channel. Buy using my Amazon links
As an Amazon Associate I earn from qualifying purchases and your cost is exactly the same.
Torque Specs:
www.collegehillshonda.com/ins...
Repair Geek I think the snap ring and si amazon link leads to the same thing
@@NikolaTesla64 fixed it. Thank you.
3⁴pl43
Very good video man!!!
Hi Repair Geek, i noticed that the torque specs on the link you added in the description are not the same as the torque specs you provided during the video. Can you explain that? I have a 2010 Civic EX and i want to make sure I am using the correct torque.
Thanks
I hope people understand a lot of time, thought and editing has gone into the making of this video. Perfect sound quality, perfect lighting and perfect camera angles with easy to see camera footage. Total quality throughout hope to see many more, thumbs up and subscribed. THANKYOU
Suree
You literally saved my day... It hadn't occurred to me at all that I could cut the old bearing off the hub. Thanks!!!
Just wanted to take a moment to add (like so many others), I too found this video hugely helpful for my own 2009 Honda Civic wheel bearing replacement. Rented all of the tools from O'Reilly Auto Parts. Thank you for a video well done!
I just replaced one of these wheel bearings and I am an experienced technician. I knew the encoder ring for the abs sensor had to go in first because I have installed them backwards! So like a dummy instead of using a paper clip or something to see which side was magnetic I used the magnet on a pocket screwdriver. I completed the job everything went smooth and when I went on a test drive the dreaded abs light came on. Everything was installed properly and the abs sensor was fine so I was really puzzled on why I had an abs light with codes for the left front which I just replaced. Turns out my magnet on the pocket screwdriver damaged the abs encoder ring! Do not hold a magnet of any kind up to the magnetic encoder ring on the bearing as it will destroy the magnetic field on the encoder ring where you touched it with another magnet. So I will be doing this job all over again eliminating any profits I earned from doing it the first time...all this just because I touched the encoder ring side of the bearing with a magnetic pocket screwdriver...crazy
Wes Snyder Good to know thanks for sharing, I am going to try to replace one on my Gen 3 Odyssey.
Perhaps your magnetic tipped screwdriver did not damage the abs decoder ring, but simply gave you a false positive on it's location, leading to you installing it backwards
Are you sure the Axle Nut was tight enough? On a few occasions, my torque wrench was clicking (at the specified torque) like the nut was tight and there was still a lot of play in the shaft (the nut was not fully seated). Now I usually tighten the nut until that play is gone in the CV Shaft, then torque it to spec. If the Axle Nut is loose, the ABS light will come on because the reluctor wheel is not staying aligned with the sensor. Tightening the nut will possible fix your issue. Hope this helps!
Uhh 😬 done the same n just don't work on your car drunk as well...
Wow. That sucks. Thanks for the tip
Wow. Thanks a lot! Just what I needed before going to do it myself. Clear and complete description of the process!
Love your repair style. It gets the job done efficiently and with all the same safty gear I would use.
What is safty?
Very nice and well explained video. I just change my Civic 2008 bearing following your instructions. Thank you for taking the time doing this. Save me a lot of time.
Best video on this process I've found. Thanks.
Great job on the video. Out of a number of videos I watched you are the only one that mentioned the magnetic side of the bearing
You have the simplest style of replacing Honda wheel bearing,All of the video out there is much harder than what you did.You replaced it without removing the knuckle off the car,Excellent job.I'm a new fan of yours now.Forget Eric the car guy.
Nice. I would put some anti-seize on the spleen of the CV Axle for easier removal next time and also on the hub where the wheel meet.
Thank you. After seeing this, I've decided to just buy a whole new assembly rather than buy a bunch of new tools i wont normally need.
Don't own a Honda but pretty much the same process for all press fit bearing replacement. Very detailed and precise explanation. The work place is well organized and clean. Thanks for sharing.
Most cars are the same :(. Due to patents, they are all the same. Honda, BMW, Toyota, Etc, Etc.... They buy the parts from the manufacture and slap it on.
Unbelievably helpful, especially with all the links to the tools and parts. Thank you!
Great video, help me a lot to changed wheel bearings on my car. Thanks Buddy.
This is the best video I watch,do not take apart the all thing,more easy less time.wow.God bless you.
Great video. I'm about to tackle a 2012 rusty civic bearing and trying to decide if I should remove the strut bolts or the ball joint; so it was nice to see it done the way you did as I normally remove the ball joint. I'm not a fan of using an impact wrench with the bearing press tool; especially on the re-install. Not only does the tool itself say not to; but when the bearing bottoms out on the install it is easy to over-torque it and either ruin or shorten it's lifespan. I also found that putting the bearing in a freezer (an hour or more) does help make the install much easier. Thanks for sharing.
That’s a great idea
Great video man! You're a good teacher 😁👍
I'm doing my 96 Civic EX and my Official Honda Service Manual didn't have the right sizes for the tooling to be used with a press. I was shocked! My bearing is considerably larger than the one for the CX and DX apparently but the Honda manual made no mention. Seeing you use the slide hammer eased my mind regarding damaging the ball joints because that is the method I will be using. Thanks!
Great job Sir, a real mechanic for a change, thank you
Great video and information!! You definitely know the procedure and work it takes to do this!
Thanks for the tutorial. If I had a more set-up garage I would try that. But I think the average home, DIYer doesn't have half those tools and equipment working on the driveway, so the $350 my mechanic wants to replace both front bearings seems like a bargain compared to the time and effort it looks like you went through.
Thank you for posting very clear informative presentation exactly what I needed
So clear in your descriptions on how to do this very happy thanks mate
I have a lot of work cut out for me on my own Civic hatchback (eu spec) and I'm so glad you mentioned the magnetic side of the bearing, as I was kind of wondering which side that would be, as there was no obvious indication on the bearing itself. great vid, and thanks:)
Black side out, brown in.
Fantastic quality, very happy that I found this video!
Wonderful video! No BS and a full video of each step.
Great video for showing how to set up the tool not only how it works... liked and subscribed.
Good job, lad! It gave me that much more confidence to tackle mine.
Really love the way you worked and made such a nice video thanks
nice job thanks for sharing wish I had that tool today the civic I did today had cam bolt in the top so the front end alignment they just did is shot if I had that tool take the ball joint lose leave the struct alone . thanks again will be buying the tool
I love to see things, like you'll never get the sensor out because of rust. All too often I see a video from areas that don't have rust and they never show how much that further complicates the issue. For me, had to replace the dust shields because they were basically gone as well.
Good mechanic and good presenter!
Solid video man. I rarely subscribe, but you got mine.
Great explanation on the proper placement of the bearing.. It may be the most important tip for the do it yourself mechanic can get. I've seen others that do not let people know about the ABS feature built into the hub and consequently some mechanics are bewildered at why the ABS fails to work properly. Congrats on a great job in the work and the explanation. thanks also for the links on the tool s you used in this repair, in your description. going to subscribe, I'd like to see more of your work
nice job, Thanks for sharing
Hi,thank for sharing.
I have a question. Can I use the same way to take out my hub by the slide hammer on my 2011 Honda Accord SE 2.4L? Thank you so much.
Absolutely phenomenal video sir 💪
Keep them coming
thanks you are very good to show have good time bye
This is what I was looking for. I really don't want to deal with a stuck bearing on the hub so I want to buy the hub separate and just replace the old one. This will save me a massive headache since I don't have the tools (not confidence) to cut out the outer bearing from the hub. Thanks!
This helped a lot. Thank you so much for putting it a great video together
Great video very detailed covered all the little questions I had.
Great filming and explanation! You made it look easy!
Saved me a lot of time. Thank you!
Thanks brother, your video was very helpful and informative 👍🏾, keep it going man I already subscribed to your channel.
perfect demo bro..love it...
Great video! Thank you for sharing.
Nice work buddy! Love the approach, too late for me, i already bent the upper caliper bracket arm trying to press out the bearing using a press, now it's in the bin & I'm down another car! Oh boy 😯
The best video on how to do it.
thanks for the torque specs. If I did it to save hiring both those tools I'd take the bottom ball joint off, take the hub and assembly off and try a range of sockets to drift the bearing out and back in again, failing that I'd take it to a garage and get the bearing pressed out /in
Great Job Sir!! Thanks For Sharing!!
Great video, it help me with my 2013 Civic.
Very good and clear video if only they were all like this and have subscribed!
Very good point at 13:50 about supporting the inner race. If you support anything else you will damage the bearings while pressing in the hub. Never press against bearings.
Great video, well explained, good lighting and video work. Curious, what would/did a front wheel bearing run at the shop? Do you recommend doing both at the same time or just as needed?
What size nut (axial nut) is that you used the impact on? I know it's big! Thank you!
Very detailed, explanation helpful.
Just what I needed for reference, perfect!
Do you know if it’s the same parts and process for the hybrid model?
Would it be possible to use this same method on AWD 2004 Honda crv Rear Side? (NOT REMOVONG SPINDLE METHOD) using the tool you show? Such a great video Thank you!!
I thought when you press a hub in you need to make sure the cup pushes from the inside of the inner bearing ring. maybe I couldnt see the size of the cup you used just wondering your thoughts. usually rule of thumb is outside of the bearing when you press it in and the inside of the inner bearing when you press the hub back on.
Thanks for the great video.
Are the hubs side specific? Ordered 2 si hubs and they look slightly different with one having a sort of lip coming off the edge
Ha i always get confused with shift loading. So i do a slight turn to the left. It means all the load will be on the right side correct? If that true that mean my right bearing is toasted :(
Thanks so much for your video and teaching. I'm going to do this on my daughter's 2005 CR-V front bearing (AWD)). Does vehicle require an alignment afterwards?
does this work for an 07 honda crv as well. I just watched a video on it and the guy used a hydraulic shop press and not that thing you used. Which is easier?
Any idea if this applies to other cars as well? Was thinking of trying to use this method on my 2003 civic if I confirm it’s a bearing.
In a pinch if you couldn't get your hands on a slide hammer, could you use an air hammer from the rear of the hub to get it off?
Super helpful. Thank you very much!
Thanks for the video. I was trying to take the spindle off the other day but it was impossible with the rust condition (no penetrant at the time).
Now I know how to do it right!
This was so helpful thank you
That's the videos should be. Thanx man!
great job, thanks
I don't have a civic but really enjoyed this video! All the bearings I've replaced are pressed from the rear, which I think would be difficult to do with the knuckle still attacked to the car, so I've always removed it and done it on a vice. I take it you do it this way to save you having to remove the bottom ball joint?
great video! thanks for sharing it. I guess the job would be similar for a tacoma with front end bearing needing replacement...do you have a link for a torque list for tacoma 4x4 2007?
I'm assuming an 06 is basically the same truck:
drive.google.com/file/d/0B-P_0I7UKquvQjd5TXFidXFGZWM/edit
Really cool video to know how to use a wheel bearing tool. Do you think for any car should be the same prrocces ? Thanks so much.
Very good instruction.
Last week I did this on a 05 accord. After struggling to get the bearing to go In straight, I took it to a shop that damaged the abs side if the bearing during the install. I’m getting ready to attempt the job again, any tips on getting the bearing in straight?
your the man... thanks
I feel road noise on slight patchy road, is the the wheel nearing? Ps: just overhauled full suspension, joints etc and fairly new michelin primacy st tyres.
Good video never use a standard ball pein hammer on brake disc always copper or lead mallet.
Got those same snap ring pliers the other day from home depot. Lol. Only one the sold.
Do I apply a little bit of lube on the bearing before pressing ? Same for the shaft into the bearing ?
What a fantastic video. Sure wish you were close. At 72, I am getting old for this and sure would be nice to have someone you trust.. I replaced both rear hub bearings on my 2007 2dr Civic EX with 177K on it ( my student's car). Back right was totaling failing when I caught it. Then you could hear right rear in turns. It was rough. Replaced the two compensating bushings in the lower front control arm. Backside under was torn That stopped a clunk in bumps that I thought was top strut mount going bad. Now with all tight when you turn and let the steering wheel spin back, you can fill a shutter bump fill in steering wheel and a pretty noticeable howl as you pull out driving along straight. One axle is new. Other fills good. Hard to believe boots are still good. (My 85 and 93 failed at 80K. Even the one I replaced was still good till a shyster stuck it with a scribe down in the bottom of the V at the Honda dealer at state inspection. Years ago the boots were about $40. Now it's cheaper to put in a new axle and sure lot less messy.
I guess the only true way to check is to take the axle out unless the bearing is failing loose.
My question have you ever seen one go past 180K and be OK? Could my howl be in automatic transmission? It fills and shifts great. I have always used 3 quarts of synthetic Honda fluid in it ever 3rd motor oil change
Yes these cars are plenty reliable well past 180k. Just like anything else it obviously depends on maintenance and driving habits but for the most part they are good cars.
@@RepairGeek Took it down and pulled axle. Both bearing smooth and no play. Axles smooth and little shake. Guess the howl is the old tires. 180 K. Honda builds good stuff. Mine even is rust free. Brake pads are apx 3/4 gone but they are the replacement I put on at 100K.
Shame the motor has front casting antifreeze leaks. But the stop leak light duty pellets seem to have fixed it. Took about 6 months. Dosed it twice. Monitored it closely and probably added a couple gallons till it finally sealed.
Thank you for sharing this video, Great work. Ever since I replaced my front right bearing with this method. My cv shaft has excessive play which cause clunking and also abs light is goes on.
What I feel is the use of slide hammer may misaligned camber or toe angle.
You didn't tighten the Axle Nut enough. Take off the wheel, pop the center cap out of the wheel, put the wheel back onto the car, then drop the car/wheel down on the ground and tighten the nut until that play is gone in the CV Shaft, then torque it to spec. The ABS light is coming on because the reluctor wheel is not staying aligned with the sensor. Tightening the nut will fix both issues. Hope this helps!
Great video...thanks for posting
Master at work 🙏🏾🙏🏾
Well Done! Thanks for sharing.
Would you need an alignment after removing the strut bolts
Thanks for the video and I just found your channel. No hate.. just a comment. My 2005 CRV looks almost brand new in the brake assembly compared to that car. WOW! Sure glad I live down south. That salt is killer up there. 3:22
Great video! DO NOT REMOVE THE SPEED SENSOR! At least I didn’t need to in my ‘08 EX. Like he said, it will likely break off, and you can quickly look up other videos to see what a pain that is to deal with...My ABS light is on, but I think you gotta put everything together and take it for a ride before you can see if it’ll turn off! So avoid the headache and don’t touch the speed sensor if you don’t have to. Sources online also say you should test the ABS magnet with a paper clip or something small.
Great video. U sure make it look easy. 😄😄😄
Great video thanks
Is it the same procedure for 2004 odyssey?
Muy buen trabajo gracias por tu experencia muy etico y profecional 😉😎saludos y felicitaciones
very informative. thanks!
Awesome video. Thanks for not attaching the camera to your wrist and making everyone nauseous!
Have a '99 Si. What is different? Is your torque link for the Si? Don't see anything in the specs referring to the Si model.
I have a 2008 hybrid will it be the same process for repair?
Great video! Does this method affect the alignment or is this a way to avoid having to do the alignment. I have to do mine on a 2012 lx coupe and didn’t know it was gone until I had an alignment.
Did you have to get another alignment?
My 2011 Civic needs new wheel bearings. Any idea what a fair repair estimate is?