Speedhack Ninebot G30 controller St link New
Vložit
- čas přidán 14. 06. 2023
- Welcome to visit our webshop
www.wattsnabb.se/en
You can send youre controller to us and we will st link it. If you are outside EU send us a message info@wattsnabb.se We need to do a special shipping to avoid taxes when you shit controller to us and will guide you how to do.
www.wattsnabb.se/products/upp... - Hry
Another question for you. When you said “I will change my serial number” 12:37 . Do you just change it to the serial number on the side of the scooter or do you pick an arbitrary serial number? Thank you for the help thus far!
Its depends witch motor you have. If you have a new motor(PADH)then I use serial on the side. If its a gen 1 or 2 them i use somting like N4GSDXXXXCYYYY
X is year and week ex 2330 and y is whatever number you like ex 1337
When I followed your previous tutorial for the 3 capacitor board with the debug terminals on the bottom and soldered them to it like you said in that video. When I click launch recovery button it says “couldn’t connect to ST-Link” any suggestion on what to do? I have verified that my solder connections are solid and not interfering with each other. Thank you!
Hi. Have you checked so all connection is right and that you have installed all st link drivers properly?
@@WattsnabbAB just went back and verified the drivers and they weren’t correct. Fixed that and it worked! Now it’s shaking like it did near the end of your video so I’m going to try the fix you did once my android device is charged. Thank you for the response!
Edit: in case anyone sees this in the future I downloaded the new drivers from the ST website STSW-LINK009. Extracted them in a folder on my desktop and told the STLINK to find the updated drivers there
@@sethhubbard698 if you have the new motor you need to do same serial number as on scooter and use shfw(187) for it to work. Sometimes you need to install shfw 2 times for it to work.
Dio = data input/output, to bring or get data
Clk = clock, for reading the actual data
Sw = switch, your blue device
Good video 😃
Great video, thanks !
I wonder how you aliment the controler when you try to flash it with stlink and the two cable on the front ?
You talked about an adapter ? Do you know how to find this adapter ?
This is for the 5v and the ground, right ?
Thanks :)
Thanks. Its then dashboard connector. I had a spare of them. You can also solder on the dashboard for 5v and gnd. So i connect a dashboard connector to the controller and from it connect 5v and gnd to the st link.
Cool video, thanks from Bielefeld. Is it a special glue (or jelly) where you connect the cables to the board (I can'T fix them)?
Greetings from Krautland 🙂
Hi Bielefeld :)
Ido you mean the Silicone in the controller? I'm unsure witch name it have but it's is Silicone.
Thank you for this information but I have one question. I have a nine bot G 30 I try to flash a custom firmware, and now the scooter won’t turn on long enough to connect to the Bluetooth. Turns on briefly and shuts right off so I would like to know if I do this process should I be able to fix the problem?
Hi. You have used wrong firmware. Need to st link it.
Hi good explanation thanks. Can I ask you if I do that process and custom firmware it can I solve the reduced power issue after %70 battery left ?
No not really but becuse you increase power you will have mord power. Best way is to buy external battery to get longer range.
Have a second question is it possible to ST link a high boy max scooter?
Hi. Dont know :)
hi, you have some good videos about electric scooters
I have understood that the new (black) controller can ST-link when I select AT32..
but then I'm a little doubtful about the rest you say..
can I hack it like the others or are there limitations..
what it's about is making the animal run faster..
Hi yes you can hack it like the others, you have to use shfw and not built a firmware on web. Shfw is the config tab I scooterhacking:)
Hello again and thanks for your quick reply
I have now done as you prescribed and ST-Link my new type of controller in MAX (G30)..
I have used SHFW Regular-Base 187-v0.3.6 and tried several setups with Profiler etc. and I can only get it to work in sports mode and max 28kmh with a full battery..
if i buy one of your controllers.. is it then possible to get more speed.
@aagerasmussen107 i guess you have tier pressure over 60psi.
What you can do I use field weakning. Then you will get increased speed
Hello again
I have now set Field Weakening to the following
Start Speed: 25Km/h
Initial current: 3A
Variable current: 400 mA/Km/h
and it now runs 32 km/h
thanks for the help
@@aagerasmussen107 great to here you can increase it to 800 to
Can st-link fix the issue with DRV 1.8.7 stuck at 20kmh speed and cant be downgrade through bluetooth?
yes
Hi, i want to make with this method. Thanks for the video!
What happens if i put the current serial number of my scooter on Reflasher?
Motor shaking :(
Resolved!
@@gagash3683 haha did you miss it when i show its shaking on my video =)
@@gagash3683 great
You can use the one on the scooter.
Hi, My Original G30 Max Controller has Dies as I Cant Re Flash Custom Firmware or even Stock Now. I have Been Using an External 48V Battery Pack that requires its Custom Firmware. If I was to buy any G30 Controller, will this will ST Linker Still Work? I've been told have to use a Original?
You need to have costumfirmware to use 48v. So you need a controller that have that on it.
Even with soldered on connectors I still have trouble connecting to target.😢
Yeah hard to say why its so. I do many scooters here and only time i have trubble to connect is when my connection is bad.
Hi, is this now also possible with the new controller with AT chip ?
Hi. Yes it is =)
hi! can I come to you on a scooter and do everything in one day? As far as I understand that you are in Stockholm? What is the price for the G30P gen3?
Hi. Yes sure. You can book a time here.
www.wattsnabb.se/sidor/trim-g30
Where can I get the adapter so I don’t have to solder?
You make it :)
hey i cannot install reflasher can someone send me a link how to do it ?
May I know where to connect these 5 volts and ground?
Yes you have it in the video :)
@@WattsnabbAB On the first connector I have blue, on the second black 3 red
@@WattsnabbAB Do I have a different controller? Or are all controllers the same?
@@WattsnabbAB What if I connect 5 volts to the first connector (blue) and the second connector (black) GND?
@@user-ht5jl8mr6j connect you dashboard cable and you Will see black and red
if i buy xiaodash with 1.7.1.13 will it be able to unlock my speed limits
Hi. I don't use XiaoDash. So best is to ask them.
What program name
Reflasher
How to ST-Link Ninebot G2E?
Cant do that right now.
Hi I can’t find the app
Reflasher?